Search Results

In this study, spray images of LPG Blended Fuels (LBF) for DI diesel engines were observed using a constant volume chamber at high ambient temperature and pressure, and the spray characteristics of the fuel were investigated. The LBF spray started to vaporize at the injector tip and the outer downstream regions of the spray, like diesel fuel, because of the high temperature at these areas. There were more vaporized areas compared to diesel fuel. Sufficient fuel injection volume and volatility of LBF resulted in good fuel-air mixture, then, THC emissions decreased compared to diesel fuel at high load engine test conditions. Butane spray image could not be observed at the injector tip. It seems that the high temperature of the injector tip caused the butane spray to vaporize rapidly. Spray tip penetration with LBF and butane were equal or greater than with diesel fuel. The high volatility of LBF and butane had no noticeable effect on spray penetration.

Band spectrum images for CH, OH and CHO were taken in a heavy duty type LPG lean-burn SI engine, to investigate the combustion process as it pertains to the pollutant formation process in the post flame region. Full spectra and band spectrum flame images were observed with a bottom view single cylinder research engine and two high speed cameras. NOx emissions were also measured for excess air ratios ranging from 1.0 to 1.6. A thermodynamic model, including the detailed chemical kinetic mechanism for LPG and NOx formation reactions, was developed to predict the major reaction species in the post flame region, and NOx emissions during the combustion process. The model qualitatively described the flame images for each band spectrum and could predict the measured NOx emissions very well.

Experiments were conducted to operate a direct injection (DI) diesel engine by using Liquefied Petroleum Gas (LPG) as a main fuel. Aliphatic Hydrocarbon (AH), cetane enhancing additive and lubricating additive were also added to the LPG so that smooth operation was achieved with a wide range of engine loads. Since the lubricity of LPG is lower than the diesel fuel therefore lubricating additive was employed to enhance the lubricity of LPG blended fuel. Furthermore, prototype LPG diesel truck was developed in this work, and the mileage reached about 70,000 km without any major failure. Prototype truck has good starting, good drive-off, acceleration and braking characteristics.

This research investigated the performance and emissions of a direct injection (DI) Diesel engine operated on 100% butane liquid petroleum gas (LPG). The LPG has a low cetane number, therefore di-tertiary-butyl peroxide (DTBP) and aliphatic hydrocarbon (AHC) were added to the LPG (100% butane) to enhance cetane number. With the cetane improver, stable Diesel engine operation over a wide range of the engine loads was possible. By changing the concentration of DTBP and AHC several different LPG blended fuels were obtained. In-cylinder visualization was also used in this research to check the combustion behavior. LPG and only AHC blended fuel showed NOX emission increased compared to Diesel fuel operation. Experimental result showed that the thermal efficiency of LPG powered Diesel engine was comparable to Diesel fuel operation. Exhaust emissions measurements showed that NOX and smoke could be considerably reduced with the blend of LPG, DTBP and AHC.

In this study, performance and emissions characteristics of an LPG direct injection (DI) engine with a rotary distributor pump were examined by using cetane enhanced LPG fuel developed for diesel engines. Results showed that stable engine operation was possible for a wide range of engine loads. Also, engine output power with cetane enhanced LPG was comparable to diesel fuel operation. Exhaust emissions measurements showed NOx and smoke could be reduced with the cetane enhanced LPG fuel. Experimental model vehicle with an in-line plunger pump has received its license plate in June 2000 and started high-speed tests on a test course. It has already been operated more than 15,000 km without any major failure. Another, experimental model vehicle with a rotary distributor pump was developed and received its license plate to operate on public roads.

Using an extended bottom view piston having a quartz window, flame propagation observation and flame contour analysis were carried out to investigate the combustion characteristics of a heavy-duty type LPG lean burn engine. The swirl ratio and piston cavity configuration were varied to investigate their effects on combustion and engine performance. Gradual reduction of NOx but increased hydrocarbon emissions were measured for leaner mixtures compared to the stoichiometric operation. High swirl apparently accelerated the initial flame kernel development, as evidenced by a shorter crank angle interval from the spark ignition to the maximum cylinder pressure. The ‘D’ type cavity, with an increased squish area located below the intake valve, was shown to have the shortest burn duration among the piston cavities tested. The experimental flame propagation observation procedure was shown to be useful for the study of the combustion process in engines.

This is a preliminary work for the development of a stratified combustion engine using liquefied petroleum gas(LPG) as an alternative fuel. The main objective of this research is to find out the optimizing engine parameters from the viewpoint of mixture formation with the aid of simulation, where the KIVA_ code was used. The combustion characteristics of LPG and gasoline are different because of their different physical properties. Therefore, the numerical simulation was performed for optimizing engine parameters by changing the piston and cylinder geometry, as well as injection conditions. Result showed that geometry of combustion chamber has a great influence on mixture stratification. Also, weaker swirl seems to be better for mixture formation in the vicinity of the spark plug.

Flame propagation at elevated pressures for propane, butane and autogas (20% propane and 80% butane by mass) were investigated. Flame arrival time was measured using ionization probes installed along the wall of a cylindrical combustion chamber. Flame radius was also measured using a laser schlieren technique. Results showed that the flame front speed decreased with increasing initial pressure, and the initial pressure effect on maximum flame front speed was correlated by the relationship Sf = 175·pi-0.15 (for Φ=1.0). Characteristics of flame front speed between propane, butane and autogas were very similar, whereas at fuel-rich conditions flame front speed of butane and autogas were higher than that of propane. A thermodynamic model to predict flame radius and speed as a function of time was derived and tested using measured pressure-time curves.

To find more effective lean mixture preparation methods for smokeless and low NOx combustion, a numerical study of the effects of in-cylinder flow field before injection on mixture formation in a premixed compression ignition engine was conducted. Premixed compression ignition combustion is a very attractive method to reduce both NOx and soot emissions, but it still has some problems, such as high HC and CO emissions. In case of early direct injection, it is important to avoid wall wetting by spray impingement, which can cause higher HC and CO emissions. Since it is not easy to examine the effects of initial flow and injection parameters on mixture formation over the wide range by practical engine tests, a computer program named “GTT (Generalized Tank and Tube)” code was used to simulate the in-cylinder phenomena before autoignition.

Since dimethyl ether (DME) is a synthetic fuel, it is possible to make it from natural gas, coal and biomass. It is a low-emission, oxygenated fuel, which does not generate soot in the exhaust. Therefore, it has recently been identified as a possible replacement for diesel fuel. In Japan, the new short-term emissions regulations will be enforced beginning in 2003, and the long-term emissions regulations are scheduled to be enforced in 2005. In order to meet these more stringent emissions regulations, existing diesel engines would not be as widely used in the near future as they currently are. This will thus bring about a more widespread use of DME engines due to their low emissions potential. Moreover, when the modification of existing diesel engines into DME engines is available at a moderate cost, the wider use of DME engines can be expected. This study targeted development and application of DME engine technology for diesel engine retrofit, in a used diesel vehicle.

A feasibility study of an LPG DI diesel engine has been carried out to study the effectiveness of two selected cetane enhancing additives: Di-tertiary-butyl peroxide (DTBP) and 2-Ethylhexyl nitrate (EHN). When more than either 5 wt% DTBP or 3.5 wt% 2EHN was added to the base fuel (100 % butane), stable engine operation over a wide range of engine loads was possible (BMEPs of 0.03 to 0.60 MPa). The thermal efficiency of LPG fueled operation was found to be comparable to diesel fuel operation at DTBP levels over 5 wt%. Exhaust emissions measurements showed that NOx and smoke levels can be significantly reduced using the LPG+DTBP fuel blend compared to a light diesel fuel at the same experimental conditions. Correlations were derived for the measured ignition delay, BMEP, and either DTBP concentration or cetane number. When propane was added to a butane base fuel, the ignition delay became longer.

Development of LPG SI and CI engines for heavy duty vehicles has been carried out. In order to measure the performance and emissions of an LPG lean burn SI engine, the piston cavity, swirl ratio, and propane-butane fuel ratio were varied and tested. Compared to the bathtub and dog dish cavities, the nebula type cavity showed the best performance in terms of cyclic variation and combustion duration. High swirl improved combustion by achieving a high thermal efficiency and low NOx emissions. A feasibility study of an LPG DI diesel engine also has been carried out to study the effectiveness of the selected cetane enhancing additives:Di-tertiary-butyl peroxide (DTBP). When more than 5 wt% DTBP was added to the base fuel, stable engine operation over a wide range of engine loads was possible. The thermal efficiency of LPG fueled operation was found to be comparable to diesel fuel operation at DTBP levels over 5 wt%.

Flame propagation characteristics, in a heavy-duty type LPG lean burn SI engine, were investigated by simulation methodology, using the global one step and the ten step chemical kinetic reaction mechanisms, respectively. The swirl ratio and equivalence ratio were varied to investigate their effects on flame front speed. The effect of increased swirl intensity on flame speed was very minor at ranges of equivalence ratio of this study. Flame front shape, however, was affected by swirl intensity. Circular flame front formed for a higher swirl ratio, which is in a qualitative accordance with that of measurements. Comparison between calculation and measurements of flame propagation characteristics shows a good agreement for both the global one step and the ten step chemical kinetic model. This work concludes that the reduced chemical kinetic reactions, consisting of ten steps, is useful for flame propagation study in an LPG SI engine.

The oxidation mechanism of DTBP (Di-tertiary-butyl peroxide) and its role in butane oxidation have been investigated, as it pertains to the development of an LPG DI diesel engine. Ignition delay contours were analyzed to investigate the role of DTBP (ϕ≈0.2 to the total oxygen) in butane oxidation. At higher pressure and lower temperature regions, it was apparent that the addition of DTBP significantly enhances the ignition delay of butane, whereas at lower pressures and higher temperatures, this effect diminishes. Results of this study showed that the role of DTBP to enhance the ignition delay of the base fuel is through rapid heat release, rather than by radicals produced by decomposition during the base fuel ignition delay. Formaldehyde is a principal species involved in reactions for heat release in the higher pressure lower temperature region, comparable to diesel engine operating conditions.

This work aimed to develop an LPG fueled direct injection SI engine, especially in order to improve the exhaust emission quality while maintaining high thermal efficiency comparable to a conventional engine. In-cylinder direct injection engines developed recently worldwide utilizes the stratified charge formation technique at low load, whereas at high load, a close-to-homogeneous charge is formed. Thus, compared to a conventional port injection engine, a significant improvement of fuel consumption and power can be achieved. To implement such a combustion strategy, the stratification of mixture charge is very important, and an understanding of its combustion process is also inevitably necessary. In this work, a numerical simulation was performed using a CFD code (KIVA-3), where the shape of a combustion chamber, swirl intensity, injection timing and duration, etc. were varied and their effects on the mixture formation and combustion process were investigated.

Recently, dimethyl ether (DME) has been attracting much attention as a clean alternative fuel, since the thermal efficiency of DME powered diesel engine is comparable to diesel fuel operation and soot free combustion can be achieved. In this experiment, the effect of ambient pressure on DME spray was investigated with observation of droplet size such as Sauter mean diameter (SMD) by the shadowgraph and image processing method. The higher ambient pressure obstructs the growth of DME spray, therefore faster breakup was occurred, and liquid column was thicker with increasing the ambient pressure. Then engine performances and exhaust emissions characteristics of DME diesel engine were investigated with various compression ratios. The minimum compression ratio for the easy start and stable operation was obtained at compression ratio of about 12.