Search Results

With the improved safety performance of vehicles, the number of accidents has been decreasing. However, accidents due to driver distraction still occur, which means that there is a high need to determine whether a driver is properly looking at the surroundings. Meanwhile, with the trend toward partial automatic driving of vehicles in recent years, it is also urgently required that the state of the driver be grasped. Even if automatic driving is not installed, it is desired that the state of the driver be grasped and an application for control be performed depending on the state of the driver. Under these circumstances, we have built an algorithm that determines of the direction a driver is looking, to make a basic determination of whether or not the driver is in a state suitable for safe driving of the vehicle.

Development of a system which utilizes technology for the recognition of a vehicle's surroundings. Research is currently taking place in many countries, the goals of which are to improve a vehicle's safety and convenience by reducing driver strain through the automation of the recognition, judgment, and operation capabilities that are needed when driving an automobile. To recognize the vehicle's surroundings, we have adopted an image sensor system which offers superior three-dimensional recognition capabilities. In this paper, we will introduce a inter vehicle distance control system which controls the vehicle's throttle and braking functions by detecting the position of the driving lane and the distance to the vehicle in front based on the images obtained by a CCD camera.

Recently two-mass flywheels have adopted in various types of engines to decrease torsional engine vibrations. A two-mass flywheel has a resonance frequency below the idle speed. Thus, it must be provided with an energy dissipating mechanism to avoid a resonance problem. Consequently, flywheel's damping effectiveness at practical engine speeds is decreased because the energy dissipating mechanism restricts relative displacement of the two-mass flywheel. In this work, a new prototype two-mass flywheel was evaluated and found to be effective in improving two important qualities of such devices; (1) its ability to decrease torsional vibrations (2) its ability to avoid resonance problems during engine startup.

In a system with which acceleration and braking by the driver are automated, a gap against the system can be felt when the timing of acceleration or deceleration is different from that intended by the driver or the extent of acceleration or deceleration exceeds an acceptable limit. For an automated system, it is important to realize a control that provides comfort and a sense of security for the driver. This paper is related to the technology that secures the ride comfort felt by the driver (comfort and a sense of security) within an appropriate range and presents a discussion of the technological means to improve the ride comfort from a viewpoint particularly related to longitudinal direction.

Brazing using arc-sprayed coatings was investigated for application to non-oxidation copper brazing. It was found that the more porous sprayed coatings have an excellent brazeability. This newly developed joining method is more suitable than conventional methods for brazing complicated parts. We have applied this method to fabricate a torque converter for practical use.

Over the past decades, the automotive industry has made significant efforts to improve engine fuel economy by reducing mechanical friction. Reducing friction under cold conditions is becoming more important in hybrid vehicle (HV) and plug-in hybrid vehicle (PHV) systems due to the lower oil temperatures of these systems, which results in higher friction loss. To help resolve this issue, a new internal gear fully variable discharge oil pump (F-VDOP) was developed. This new oil pump can control the oil pressure freely over a temperature range from -10°C to hot conditions. At 20°C, this pump lowers the minimum main gallery pressure to 100 kPa, thereby achieving a friction reduction effect of 1.4 Nm. The developed oil pump achieves a pressure response time constant of 0.17 seconds when changing the oil pressure from 120 kPa to 200 kPa at a temperature of 20°C and an engine speed of 1,600 rpm.

We have developed a Hall effect device based height sensor of a smaller size, and with higher temperature operation durability, as compared to conventional devices. Downsizing of the sensor is realized by decreasing a number of parts, and by employing a short bearing. Improvement in heat resistance is achieved by adopting an IC with sufficient heat resistance and a SmCo magnet with high coercive force. In addition, a sensor of a high degree of accuracy is accomplished by improvements in linearity and robustness of magnetic characteristics. Development of a small, heat-resistant and accurate height sensor will promote the spread of systems using a height sensor, such as a High Intensity Discharge (HID) headlamp.

One of the problems concerning T/M is conventionally how “Improving the input torque as the engine gets higher power” and “Making product lighter in weight and more compact to improve the fuel consumption” can be realized at the same time. To realize these things at the same time, it is needless to say that the gears must be stronger. For the “pitting fatigue strength” which is quoted as a problem lately, the fatigue mechanism has not been clarified, yet. Therefore, it is now a big problem how to achieve high strength. In the meantime, we tried to develop the production engineering for “finer crystal grains” and “fine-dispersion precipitation of carbo-nitrides,” and succeeded in improving “pitting fatigue strength” remarkably. Such results will be reported in the following sections:

Electrification of the powertrain to improve vehicle fuel economy is a key technology to achieve strict fuel economy legislation. However, only limited numbers of small class vehicles such as a B segment adopt electric powertrain. This is presumed that cost effectiveness for fuel economy is small and mounting space for additional powertrain is limited. In this paper, the optimum solution of a strong hybrid system suitable for the small vehicles was studied. First, from the viewpoint of maximization of energy efficiency, we compared contributions of engine efficiency and transmission efficiency during mode cycle driving and selected automated manual transmission as a suitable transmission for small vehicles. In comparing the hybrid system function, we determined a motor generator connecting shaft and a necessary motor generator output power for attaining both fuel economy and drivability.

AISIN SEIKI CO., Ltd. Started the production of electronically controlled hydraulic automatic transmissions for medium-duty trucks and buses in 1989. The number of vehicles on the Japanese market in which this system is adopted is increasing steadily. After re-examining market needs, AISIN SEIKI CO., Ltd. has newly developed an electronically controlled hydraulic automatic transmission A580 which focuses on improved input capacity, driving performance and fuel economy for medium-duty trucks and buses and lessens learnt from experience.

As a process that enables the high-speed and continuous forming of lengthy materials with a constant cross-sectional configuration, roll forming offers much higher productivity than the stamping process. However, in case a change must be made to the shape of the cross section, the material must normally be stamped or joined with a part containing a separate shape. This affects productivity, increases the number of pieces, and degrades the material's appearance. This report describes the roll-forming technology that we developed, in which the cross section of the material can be changed gradually. This method adopts a system which uses a movable and rotatable roll-stand that enables high-speed, continuous roll-forming processes.

While exhaust gas emission standards are becoming severe, turbochargers which have a good performance and wide operating range are required. At Aisin Seiki, we have started development of the SJ (swirl jet) turbocharger to cope with these requirements without increasing costs. In this paper, we describe the features and effects of the SJ turbocharger.

Switched Reluctance Motor (SRM) mainly has two advantageous characteristics such as no magnet and simple construction. These characteristics contribute lower cost and higher reliability compared with other motor systems such as brushless permanent magnet motors or induction motors. However, acoustic noise and output torque ripple should be improved when the SRM is applied to a traction system for passenger electric vehicle since these characteristics directly affect vehicle quietness and drivability. In this paper, we describe a system configuration of the SRM traction system for passenger electric vehicle. The SRM traction system includes an electric motor, transmission gears and power inverter module. Then, an approach to improve acoustic noise and output torque ripple is introduced. Generation mechanisms of acoustic noise and output torque ripple are analyzed.

Exhaust emission regulation has become stricter year by year because of the global movements of environment protection. In consequence, turbocharger application to diesel engines became indispensable. Especially a variable geometry turbocharger (VGT) is perceived as the essential item. Of late years, the diesel engine has a trend of higher exhaust temperature to increase specific output. At the same time, needs of the turbocharger application to the gasoline engine has been rising again in order to reduce the size. In spite of this trend of the emission temperature increment, VGT of the variable nozzle vane type which is commonly available in the current market has problems of high temperature resistance due to its complex structure. AISIN SEIKI has developed a variable flow turbocharger (VFT), which is able to resolve those problems.

Recently, plastic air intake manifold (PAIM) has been adopted into gasoline and diesel engines as standard equipment. The advantages of the PAIM are light mass weight, low cost, high thermal-insulation efficiency and reduction of air pressure loss compared with a metal air intake manifold. However, in order to bring the advantages of the PAIM into play, many issues including static burst, noise and vibration, and so on should be settled in its design process. In this paper, the performance prediction and application example of PAIM are introduced.

There are such outside door handles called smart handles which have a transmitting antenna, a lock/unlock sensor, and a sensor detection circuit, with which operation of door lock is possible just by "touching" the electrostatic-capacitance type sensor of the handles.As the design of the outside handles, body color painting and Cr plating are adopted. However, if plating is applied over the entire surface of a smart handle, electromagnetic waves transmitted from the antenna will be blocked since plating material is electrically conductive. In addition to this, touching a part other than the sensor may change the electrostatic-capacitance of the sensor, which results in unwanted functioning of the lock/unlock sensor. Because of this, only part of the handle, which does not hinder the transmission of electromagnetic waves and does not cause unwanted functioning, is covered by plating, that is called, "Partially plated specifications" (Figure 1).

Automating the inspection of the piston combustion chamber volume is difficult and prevents establishing an unmanned machining process of the piston in the future. So, we developed an inspection technique which uses a Range Finder, non-contact visual sensor, and calculate the chamber volume by integrating 3D position data. We applied this real-time measurement technique which enables 100 % inspection to our production lines. Then, we developed the “Defect Free Production Line”, which calibrates itself by feeding back the measured volume data to the machining process. Our paper will explain this inspection technique and our “Defect Free Production Line”.

Responsiveness is one of the main characteristics of a brake booster. The design of a tandem booster, with its two boosting chambers, has a negative influence on high responsiveness. This report, using the CFD method for the air flow analysis, shows the way we found the most suitable air passage within the space of the given design of the current production tandem booster.

As a part of our process engineering (planning) steps and in order to shorten the initial flow control after the implementation of a production system, we have been adopting countermeasures for defects that have been forecasted by the application of FMEA. However, due to this having to be done with limited information (which is dependent upon the skill level of the operator) and due to the fact that the effects of each particular countermeasure are not fully understood, we cannot be certain that the measures implemented during the planning stages are thorough enough. The current situation is that countermeasures for most issues are being handled during the initial flow control stages based on the trial-and-error method. Given this situation, normally, it would take us more than three months from the time of line-off (start of production) to achieve our target rate of capacity utilization.

When a clutch pedal is operated, the clutch pedal vibration and interior noise are mostly affected by the dynamic characteristics of the clutch cover assembly. We achieved a high correlation between vehicle test data and results using this method when exciting not only clutch system but also the engine system. Finally, we developed an excitation method to evaluate the dynamic characteristics of the clutch cover assembly.