Search Results

As one of the core components of electric vehicles(EV), the drive motor system has a significant impact on the EV operation performance. The interior permanent magnet synchronous motor (IPMSM) has a wide range of applications in EV, due to its high efficiency, high power density, high torque current and wide speed range. In the field of EV, motor control system is required to have a high operating range. IPMSM operates at constant torque mode below rated speed and constant power mode above rated speed. The back electromotive force(Back-EMF) generated by the rotor in the constant power mode causes the inverter output voltage to saturate. Therefore, it is necessary to ensure that the controller is still operating in the linear region by applying a flux weakening(FW) current to the stator.

With the continuous development of the electrical vehicles (EVs), the electric power network and transportation network are interconnected by EVs which require a coordinated operation of the two networks. In view of these coupled networks, this paper proposes a charging navigation strategy for EVs based on charging power adjustment, which can not only provide the navigation path with the shortest total operational time for EVs from the origin node to the completion of charging, but also effectively reduce load fluctuations in the electric power system. In the electric power system, an innovative optimization strategy for adjusting the EV charging power distribution is proposed, which can adjust the charging power in a timely and effective manner according to the response of EV charging. The multi-objective particle swarm optimization (MOPSO) algorithm and the improved Dijkstra algorithm are used for solving the obtained the EV charging power adjustment plan and charging paths.

T-BOX can manage the vehicle’s operation data and position data, and provide the following functions, positioning, vehicle status, motor data, BMS working status, charging status and status alarm, which may effectively promote the development of electric vehicle. Meanwhile, it may bring a series of problems, especially the electromagnetic compatibility (EMC) problems. In this paper, for the exceed standard limits problem of a particular T-BOX sample in radiation emission (RE) and conducted emissions(CE) test process, π filter is designed and added to the positive polar and negative polar of power supply based on the analysis of hardware circuit. The conduction emission test results of T-BOX after optimized can meet the requirements of GB/T 18655-2010 Vehicles, boats and internal combustion engines-Radio disturbance characteristics-Limits and methods of measurement for the protection of on-board receiver standard.

A vehicle’s NVH performance has a significant impact on the user experience of the driver and passengers. About one-third of the vehicle complaints are related to NVH performance. As the core component of the vehicle, the drivetrain’s NVH characteristics have a significant impact on vehicle comfort. How to reliably and stably reproduce the specific condition of the whole vehicle through the test method, and obtain the highly consistent objective data for analyzing and improving the NVH characteristics of the drivetrain is of great significance in engineering. For this purpose, China Automotive Technology Research Center Co., Ltd. (CATARC) designed and built a new type drivetrain NVH test facility, which consists of five dynamometers, and can carry horizontal/vertical, front/rear drive or four-wheel drive structures including powertrain, transmission, and rear axle, or even a whole vehicle.

This paper presents a novel powertrain control system specifically designed for longitudinal motion-control applications of an automated-manual-transmission vehicle, whereby the clutch and throttle modulation and gear change are highly coordinated such that the vehicle can precisely track the target acceleration or deceleration command even during an upshift or a downshift. An observer-free method for estimation of the engine’s operating point under various working condition is developed to compensate for limited sensing and enable effective feed-forward control of the engine torque and the clutch pressure. With minor modifications of the coordination strategies in the existing powertrain control system, the proposed control system can prevent stalling the engine from a standing start and achieve smoother shifting and faster dynamic response of the powertrain system, where non-smooth actuator nonlinearities are addressed explicitly, robustly, and efficiently.

Electric vehicles are considered as one of the most popular way to decrease the consumption of petroleum resources and reduce environmental pollutions. Motor control system is one of the most important part of electric vehicles. It includes power supply module, IGBT driver, digital signal processing (DSP) controller, protection adjustment module, and resolver to digital convertor. To implement the control strategies on motor control system, a lot of practical aspects need to be taken into accounts. It includes setup of the initial excitation current, consistency of current between motor and program code, over-modulation, field weakening control, current protection, and so on. In this paper, an induction motor control system for electric vehicles is developed based on DSP. The control strategy is based on the field-oriented control (FOC) and space vector pulse width modulation (SVPWM).

With the increasing frequency of fire incidents of electric vehicles, the safety of power batteries has attracted more and more attention. At present, the research on the safety of power batteries is mainly focused on fresh batteries. As the state of health of batteries deepens, how the safety of the battery evolves is not clear enough so far. This paper analyzes the external short-circuit safety of a NCM/C rectangular battery under different state of charges. The results show that when the cycle number is less than 800, the maximum temperature of the battery during short-circuit is below 130 °C. The main failure mode of the battery is bulging in volume or opening of the explosion-proof valve and there is no obvious regularity between the failure mode with the cycle life. However, when the cycle number reaches 1000, the battery goes into thermal runaway during the safety test.

The rapid advancement of new energy vehicle technology has led to the widespread placement of battery packs at the bottom of vehicles. However, there is a lack of corresponding regulations and standards to guide aspects related to vehicle bottom safety. This lack of guidance obscures the relative importance of various parameters impacting the structural safety of battery packs under dynamic impact conditions. Consequently, research on battery pack bottom collisions holds practical significance and offers valuable reference material. This study proposed a method based on the first collision point to examine the impact of bottom collisions on the mechanical safety performance of battery pack bottoms. A finite element model of the battery pack was established to investigate the effects of different impact types.

With the development of electric vehicles (EVs), hybrid electric vehicles (HEVs) and fuel cell vehicles (FCVS), high voltage and large-current are applied to cables. Therefore, it is important to avoid electromagnetic compatibility (EMC) problems of cables, and a measurement methods is necessary for the shielding effectiveness of shielding cables. This paper discusses the existing test methods of cable shielding effectiveness and summarizes the main problems and deficiencies. Then, according to the practical requirements of high voltage cable testing, the direct injection method based on the national standard GB/T 18655-2018 (modified international standard CISPR 25) is proposed. The test method is verified by constructing a practical test platform.

Pure electric vehicles are recognized as one of the most important new energy vehicle types to meet the increasingly stringent standards in energy saving and environment protection. To meet the control demands, China Automotive Technology & Research Center(CATARC) plan to develop an advanced Vehicle Control Platform(VCP) for pure electric vehicles. The developed VCP is well structured on both hardware and software and can be adapted to different pure electric vehicles easily. This paper describes the design of the hardware, the software architecture, the base software and the control strategy applied in the VCP in detail. A matching method is proposed to configure the VCP to a real VCU for the specific application by modifying the hardware channel definition and the control parameters. The paper shows successful application of the VCP on several types of pure electric vehicles.

The China Automotive Technology and Research Center (CATARC) has completed two new wind tunnels at its test centre in Tianjin, China: an aerodynamic/aeroacoustic wind tunnel (AAWT), and a climatic wind tunnel (CWT). The AAWT incorporates design features to provide both a very low fan power requirement and a very low background noise putting it amongst the quietest in the automotive world. These features are also combined with high flow quality, a full boundary layer control system with a 5-belt rolling road, an automated traversing system, and a complete acoustic measurement system including a 3-sided microphone array. The CWT, located in the same building as the AAWT, has a flexible nozzle to deliver 250 km/h with an 8.25 m2 nozzle, and 130 km/h with a 13.2 m2 nozzle. The temperature range of the CWT is -40 °C to +60 °C with a controlled humidity range of 5% to 95%. Additional integrated systems include a variable angle solar simulator array, and a rain and snow spray system.

With the advantages of flexible size and high energy density etc., pouch-type lithium ion battery cells with large capacity have been found more and more applications in electric vehicles. For these large-scale battery cells, thermal uniformity is vital for their safety and cycle life. To be specific, temperature gradients are expected to cause different degradation rates of active materials in different areas, which is possible to cause early failure or even fire and explosion of the battery cell. Thus, it is necessary to illustrate the batterie’s thermal uniformity in detail under different operating conditions. This work investigated the thermal uniformity of two 36 Ah pouch-type NCM/C battery cells with different sizes using both the thermal imaging method and thermoelectric effect method with K-type thermocouples. Experimental results show that there is an obvious temperature gradient on the surface of the pouch-type battery cell.