Search Results

The open jet wind tunnel is a widespread test section configuration for developing full scale passenger cars in the automotive industry. However, using a realizable nozzle cross section for cost effective aerodynamic development is always connected to the presence of wind tunnel effects. Wind tunnel wall interferences which are not present under open road conditions, can affect the measurement of aerodynamic forces. Thus, wind tunnel corrections may be required. This work contains the results of a CFD (Computational Fluid Dynamics) approach using unsteady Delayed Detached Eddy Simulations (DDES) to evaluate wind tunnel interferences for open jet test sections. The Full Scale DrivAer reference geometry of the Technical University of Munich (TUM) using different rear end shapes has been selected for these investigations.

For the cylinder-selective monitoring of combustion cycles in spark-ignition engines, the dynamic exhaust-gas pressure is analyzed. A time domain based diagnostic system for misfire detection has been developed and tested on data measured in a BMW 750i, V-12 engine. It uses features of the suitable low-pass-filtered exhaust-gas pressure signal by calculating differences of the locally determined extrema. For the detection and localization of all misfire combinations a simple inference system in the form of linguistic rules is used. It is shown that even within the operating areas of high engine speeds and low loads on engines with a high number of cylinders good classification rates can be obtained.

This paper provides a method that corrects errors induced by the empty-tunnel pressure distribution in the aerodynamic forces and moments measured on an automobile in a wind tunnel. The errors are a result of wake distortion caused by the gradient in pressure over the wake. The method is applicable to open-jet and closed-wall wind tunnels. However, the primary focus is on the open tunnel because its short test-section length commonly results in this wake interference. The work is a continuation of a previous paper [4] that treated drag only at zero yaw angle. The current paper extends the correction to the remaining forces, moments and model surface pressures at all yaw angles. It is shown that the use of a second measurement in the wind tunnel, made with a perturbed pressure distribution, provides sufficient information for an accurate correction. The perturbation in pressure distribution can be achieved by extending flaps into the collector flow.

The European Commission has released strict emission regulations for passenger cars in the past decade in order to improve air quality in cities and limit harmful emission exposure to humans. In the near future, even stricter regulations containing more realistic/demanding driving scenarios and covering more exhaust gas components are expected to be released. Passenger cars fueled with gasoline are one contributor to unhealthy air conditions, due to the fact that gasoline engines emit harmful air pollutants. One option to minimize harmful emissions would be to utilize specifically tailored, low emission synthetic fuels or fuel blends in internal combustion engines. Methyl formate and dimethyl carbonate are two promising candidates to replace or substitute gasoline, which in previous studies have proven to significantly decrease harmful pollutants.

Future emission regulations require further development for internal combustion engines operating on gasoline. To comply with such regulations and simultaneously improve fuel efficiency, major development trends are found in reduced displacements, increased compression ratios and turbocharging. To counteract such engines’ increased tendencies to knocking combustion, direct fuel injection systems are necessarily applied. Compared to standard port fuel injection, direct injection systems cause increased particle emissions. State-of-the-art magnet-driven gasoline direct injectors are capable of realizing various injection events of small injected mass per event and short dwell time between one another. Thereby, they facilitate multiple injection strategies, able to overcome the drawbacks of direct injection systems in relation to exhaust emissions. However, the full potential of multiple injection strategies is not yet taken advantage of.

Synthetic fuels for internal combustion engines offer CO2-neutral mobility if produced in a closed carbon cycle using renewable energies. C1-based synthetic fuels can offer high knock resistance as well as soot free combustion due to their molecular structure containing oxygen and no direct C-C bonds. Such fuels as, for example, dimethyl carbonate (DMC) and methyl formate (MeFo) have great potential to replace gasoline in spark-ignition (SI) engines. In this study, a mixture of 65% DMC and 35% MeFo (C65F35) was used in a single-cylinder research engine to determine friction losses in the piston group using the floating-liner method. The results were benchmarked against gasoline (G100). Compared to gasoline, the density of C65F35 is almost 40% higher, but its mass-based lower heating value (LHV) is 2.8 times lower. Hence, more fuel must be injected to reach the same engine load as in a conventional gasoline engine, leading to an increased cooling effect.

A novel algorithm-based approach is employed in this publication to calculate multiple direct injection patterns for spark ignition engines. The algorithm is verified by investigating the combustion and emission behavior of a single-cylinder research engine. State-of-the-art standard exhaust gas analyzers, a particle counter and an additional FTIR analyzer enable in-depth investigation of engine exhaust gas composition. With the upcoming worldwide pollutant emission targets, the emission limits will be reduced while the test procedures’ requirements to the engine increase. Special attention to the engine-out emissions must be paid during cold-start, during which the aftertreatment system lacks sufficient pollutant emission conversion efficiency. With advanced injection control, the engine-out emissions can be reduced and exhaust aftertreatment heat-up can be accelerated.

Existing electronic combustion engine control systems only guarantee a desired air-to-fuel-ratio λ in stationary operation. In order to achieve the desired λ also in in-stationary use of the engine, it is necessary to use new-technology-based control systems. Artificial Intelligence provides methods to cope with difficulties like wide operation range, unknown nonlinearities and time delay. We will propose a strategy for control of a Spark Ignition Engine to determine the mass of air inside the combustion chambers with the highest accuracy. Since Neural Networks are universal approximators for multidimensional nonlinear static functions they can be used effectively for identification and compensation purposes of unknown nonlinearities in closed control loops.

With increasing levels of driving automation, the perception provided by automotive environment sensors becomes highly safety relevant. A correct assessment of the sensors’ perception reliability is therefore crucial for ensuring the safety of the automated driving functionalities. There are currently no standardized procedures or guidelines for demonstrating the perception reliability of the sensors. Engineers therefore face the challenge of setting up test procedures and plan test drive efforts. Null Hypothesis Significance Testing has been employed previously to answer this question. In this contribution, we present an alternative method based on Bayesian parameter inference, which is easy to implement and whose interpretation is more intuitive for engineers without a profound statistical education. We show how to account for different environmental conditions with an influence on sensor performance and for statistical dependence among perception errors.

The objective of this study was to reduce pollutant emissions during cold start conditions in a spark-ignited direct injection engine, by exploring the potential of oxygenated fuels. With their high oxygen content and lack of direct C-C bonds, they effectively reduce particle number (PN) and NOx emissions under normal conditions. Methanol was chosen due to its wide availability. As methanol is toxic to humans and associated with cold-start issues, a second promising synthetic fuel was selected to be benchmarked against gasoline, comprising 65 vol% of dimethyl carbonate and 35 vol% of methyl formate (C65F5). Currently, there is a lack of detailed investigations on the cold start performance for both oxygenated fuels utilizing today’s injector capabilities. Spray measurements were caried out in a constant volume chamber to assess the spray of C65F35. Reduced fuel temperature increased spray-penetration length and compromised fast vaporization.

Increasing demand for utilities like navigation systems or user-defined electronic phonebooks on one hand and sophisticated engine and gear controls on the other hand leads to growing bus load between distributed local control units. This paper shows the benefits and the characteristics of various state of the art data-compression algorithms and their impact on typical automotive multiplex dataclasses. The evaluation and optimization of promising algorithms can be done via a proposed “communications prototyping”-approach. The hardware/software components of such a rapid prototyping package are outlined. Finally, first performance results of suitable data-compression measures are presented.

For development of new engines a ‘general purpose ECU’ for spark ignition engines with up to 12 cylinders has been developed. As part of this ECU a DSP (Digital Signal Processor)-based measurement unit for high frequency combustion analysis has been integrated. In this paper, details about this signal processing platform are given. The DSP-unit has 24 analog input channels. 12 channels are used for cylinder pressure measurement; the other 12 channels are general purpose ones. For example, they can be used for ionic current analysis. Additional digital inputs allow measurement of crank speed and crank speed variations. This is an important topic for misfire detection as part of the OBD regulations.

In this paper we present an advanced knock detection approach. The detection concept consists of a two-level feature extraction step followed by neural network detector. A knock tendency index is estimated that takes into account the statistical behavior of the knock phenomena. The configuration of the neural network is based on a signal database that was acquired under almost ‘on-road’ conditions. The experimental set-up consisted of several measurement sessions in a special vehicle test cell. In order to achieve a most realistic knock database the test engine was mounted on an in-production car.

Although hydrogen ICE engines have existed in one sort or another for many years, the testing of fuel consumption by way of exhaust emissions is not yet a proven method. The current consumption method for gasoline- and diesel-fueled vehicles is called the Carbon-Balance method, and it works by testing the vehicle exhaust for all carbon-containing components. Through conservation of mass, the carbon that comes out as exhaust must have gone in as fuel. Just like the Carbon-Balance method for gas and diesel engines, the new Hydrogen-Balance equation works on the principle that what goes into the engine must come out as exhaust components. This allows for fuel consumption measurements without direct contact with the fuel. This means increased accuracy and simplicity. This new method requires some modifications to the testing procedures and CVS (Constant Volume Sampling) system.

In the present work we investigated experimentally and computationally the unsteady flow around a BMW car model including wheels*. This simulation yields mean flow and turbulence fields, enabling the study aerodynamic coefficients (drag and lift coefficients, three-dimensional/spatial wall-pressure distribution) as well as some unsteady flow phenomena in the car wake (analysis of the vortex shedding frequency). Comparisons with experimental findings are presented. The computational approach used is based on solving the complete transient Reynolds-Averaged Navier-Stokes (TRANS) equations. Special attention is devoted to turbulence modelling and the near-wall treatment of turbulence. The flow calculations were performed using a robust, eddy-viscosity-based ζ - ƒ turbulence model in the framework of the elliptic relaxation concept and in conjunction with the universal wall treatment, combining integration up to the wall and wall functions.

One main goal of the automotive industry is to reduce the aerodynamic drag of passenger vehicles. Therefore, a deeper understanding of the flow field is necessary. Time-resolved data of the flow field is required to get an insight into the complex unsteady flow phenomena around passenger vehicles. This data helps to understand the temporal development of wake structures and enables the analysis of the formation of vortical structures. Numerical simulations are an efficient method to analyze the time-resolved data of the unsteady flow field. The analysis of the steady and unsteady numerical data is only relevant for aerodynamic developments in the wind tunnel, if the predicted temporal evolving structures of a passenger vehicle’s simulated flow field correspond to the structures of the flow field in the wind tunnel. In this study, time-resolved measurements of the empty wind tunnel and a notchback passenger vehicle in the wind tunnel are conducted.

In this work, the dynamics of hydraulic cam phasing systems are analyzed. First there will be introduced an experimental test rig, which is used to analyze the dynamical behavior of the cam phasers. The examined cam phaser, which operates like a slewing motor, is supplied with conditioned oil that matches real engine operation points. Secondly, a modular simulation approach for the cam phasing system and the whole valve train is presented. Additionally parameter studies are shown.

The increasing complexity of communication protocols for asynchronous multiplex systems requires the use of simulation during the optimisation of these protocols or the integration of other control units. Consideration of realistic communication behaviour of the connected control units is essential for performance analysis of multiplex systems. For a first pass, the use of simple statistical distributions (e.g. Poisson distribution) is suitable to get some simulation results. A better way to get realistic results is the approximation of empirical communication data through the use of more complex statistical distribution (e.g. mixed Erlang distributions). In this paper several approaches for the approximation of empirical data are presented. Beside simple statistical distributions (with one parameter), the use of more complex statistical distributions is discussed and methods for the identification of their parameters are presented.

Autonomous driving systems and connected mobility are the next big developments for the car manufacturers and their suppliers during the next decade. To achieve the high computing power needs and fulfill new upcoming requirements due to functional safety and security, heterogeneous processor architectures with a mixture of different core architectures and hardware accelerators are necessary. To tackle this new type of hardware complexity and nevertheless stay within monetary constraints, high performance computers, inspired by state of the art data center hardware, could be adapted in order to fulfill automotive quality requirements. The European Processor Initiative (EPI) research project tries to come along with that challenge for next generation semiconductors. To be as close as possible to series development needs for the next upcoming car generations, we present a hybrid semiconductor system-on-chip architecture for automotive.

This paper provides an overview of possible engine design optimizations by utilizing highly knock-resistant potential greenhouse gas (GHG) neutral synthetic fuels. Historically the internal combustion engine was tailored to and highly optimized for fossil fuels. For future engine generations one of the main objectives is to achieve GHG neutrality. This means that either carbon-free fuels such as hydrogen or potential greenhouse gas neutral fuels are utilized. The properties of hydrogen make its use challenging for mobile application as it is very diffusive, not liquid under standard temperature/pressure and has a low volumetric energy density. C1-based oxygenated fuels such as methanol (MeOH), dimethyl carbonate (DMC) and methyl formate (MeFo) have properties like conventional gasoline but offer various advantages. Firstly, these fuels can be produced with renewable energy and carbon capture technologies to be GHG neutral.