Search Results

This paper describes an environment for the development of production Engine Management Systems (EMS). This includes a formal framework and modeling methodology. The environment is based on using Simulink/Stateflow for developing a control system executable specification and a plant model. This allows for simulations of the system to be performed at the engineer's desk, which is identical performance with production software. We provide the details for incorporating production legacy code into the Simulink/Stateflow control system. The system includes a multi-rate, and event driven operating system. This system is developed to facilitate new algorithm development and automated software testing. Based on Simulink/Stateflow this specification will be suitable for use with commercial automatic code generation tools.

Both evaporative emissions and tailpipe emissions have been reduced by more than 90% from uncontrolled levels in state-of-the-art. However, now that the objective is to reach near-zero emission levels, the need for aggressive purging of the canister and fuel tank and the need for extremely precise control of engine Air/Fuel ratio (A/F) come into conflict. On-board diagnostics and the wide variation in operating conditions and fuel properties in the “real world” add to the challenge of resolving these conflicting requirements. An advanced canister purge algorithm has been developed which substantially eliminates the effect of canister purge on A/F control by estimating and compensating for the fuel and air introduced by the purge system. This paper describes the objectives and function of this algorithm and the validation of its performance.

The lateral runout of disc brake corner components can lead to the generation of brake system pulsation. Emphasis on reducing component flatness and lateral runout tolerances are a typical response to address this phenomenon. This paper presents the results of an analytical study that examined the effect that the attachment of the wheel to the brake corner assembly could have on the lateral distortion of the rotor. An analysis procedure was developed to utilize the finite element method and simulate the mechanics of the assembly process. Calculated rotor distortions were compared to laboratory measurements. A statistical approach was utilized, in conjunction with the finite element method, to study a number of wheel and brake corner parameters and identify the characteristics of a robust design.

The industry strategy for automotive safety systems has been evolving over the last 20 years. Initially, individual passive devices and features such as seatbelts, airbags, knee bolsters, crush zones, etc. were developed for saving lives and minimizing injuries when an accident occurs. Later, preventive measures such as improving visibility, headlights, windshield wipers, tire traction, etc. were deployed to reduce the probability of getting into an accident. Now we are at the stage of actively avoiding accidents as well as providing maximum protection to the vehicle occupants and even pedestrians. Systems that are on the threshold of being deployed or under intense development include collision detection / warning / intervention systems, lane departure warning, drowsy driver detection, and advanced safety interiors.

Automotive occupant safety continues to evolve. At present this area has gathered a strong consumer interest which the vehicle manufacturers are tapping into with the introduction of many new safety technologies. Initially, individual passive devices and features such as seatbelts, knee- bolsters, structural crush zones, airbags etc., were developed for to help save lives and minimize injuries in accidents. Over the years, preventive measures such as improving visibility, headlights, windshield wipers, tire traction etc., were deployed to help reduce the probability of getting into an accident. With tremendous new research and improvements in electronics, we are at the stage of helping to actively avoid accidents in certain situations as well as providing increased protection to vehicle occupants and pedestrians.

Seat belts are the primary occupant-protection devices for vehicle crashes. Field statistics show that proper usage of seat belts substantially contributes to decreases in the fatality rate and injury level. To collect first-hand information regarding seat belt comfort and usability, a questionnaire survey was conducted. The most significant problems were found as belt trapping in the door, awkward negotiating with clothes, belt twisting, belt locking up, and difficulty to locate the buckle. The survey results indicated that drivers who are over 40 years old have more complaints than younger drivers. When the driver's age increases to 55 and above, belt pulling force and inappropriate and loose fitting of the belt on the body become major issues. Female drivers have more complaints than male drivers. Short statured drivers need both hands to pull and guide the retracting of the belt.

Since the late 1980s, Delphi Automotive Systems has been very involved with the practical development of a variety of Collision Avoidance products for the near- and long-term automotive market. Many of these complex collision avoidance products will require the integration of various vehicular components/systems in order to provide a cohesive functioning product that is seamlessly integrated into the vehicle infrastructure. One such example of this system integration process was the development of an Adaptive Cruise Control system on an Opel Vectra. The design approach heavily incorporated system engineering processes/procedures. The critical issues and other technical challenges in developing these systems will be explored. Details on the hardware and algorithms developed for this vehicle, as well as the greater systems integration issues that arose during its development will also be presented.

The objective of this paper is to impart the challenges presented and the solutions derived to transform an artist's rendering into a production driver's door switch to be used in the interior of a high profile sports car. The challenges took many forms throughout the process, from data translation and packaging, to the final decorative issues. The results are a finished product providing a new approach to automotive interior switch design. It incorporates a low profile, continuous plane keypad with “soft touch” feel, tactile feedback, and integrated back lighting.

Delphi has developed a second-generation Electronic Throttle Control system optimized for high volume applications. The Delphi system integrates several unique driver performance features, extensive security/diagnostics, and provides significant benefits for the vehicle manufacturer. For Model Year 2000, the Delphi ETC system has been successfully implemented on several popular SUVs and passenger cars built and sold around the world. The ETC driver features, security systems, and manufacturer benefits are presented as implemented on these Model Year 2000 applications.

Today, electrical/electronic systems like ABS/power brakes and electric power steering are all designed to enhance, not replace a mechanical function. If an electrical or electronic fault occurs, the function reverts to the base mechanical capability. Future E/E systems, such as steer-by-wire and brake-by- wire replace mechanical linkages with electrical or optical signals as in computer networks. While these systems offer many potential safety benefits, they will require different strategies for dependability, and as with any vehicle system, they will further require that dependability be an integral part of the overall E/E system design. This paper illustrates how by-wire systems drive different dependability requirements and discusses some key technologies that are emerging to meet these requirements.

Recent advances in dependable embedded system technology, as well as continuing demand for improved handling and passive and active safety improvements, have led vehicle manufacturers and suppliers to actively pursue development programs in computer-controlled, by-wire subsystems. These subsystems include steer-by-wire and brake-by-wire, and are composed of mechanically de-coupled sets of actuators and controllers connected through multiplexed, in-vehicle computer networks; there is no mechanical link to the driver. This paper addresses fundamental benefits and issues of steer-by-wire, especially those related to automated vehicle control and steering feel quality as perceived by the driver.

Adaptive Cruise Control (ACC) technology is presently on the horizon as a convenience function intended to reduce driver workload. This paper presents an implementation of a brake algorithm, which extends the production cruise control feature. A brief overview of the system architecture and subsystem interfaces to the forward-obstacle detection system, throttle and engine management controls are described. Considerations of moding ACC with ABS and Traction Control are presented at the vehicle level. This development activity is presented in two major phases. Both phases of this development project utilize CAN controllers and transceivers to implement requirements for limited access highway driving. The initial phase of development requires the brake control to follow a deceleration command and operate “open-loop” to the vehicle controller. Vehicle test data capturing smooth stops on high coefficient surfaces is presented as insight to the braking performance of the vehicle.

Electric power steering (EPS) is an advanced steering system that uses an electric motor to provide steering assist. Being a new technology it lacks the extensive operational history of conventional steering systems. Also conventional systems cannot be used to command an output independent of the driver input. In contrast EPS, by means of an electric motor, could be used to do so. As a result EPS systems may have additional failure modes, which need to be studied. In this paper we will consider the requirements for successful EPS operation. The steps required to develop diagnostics based on the requirements are also discussed. The results of this paper have been implemented in various EPS-based programs.

The purpose of this paper is to investigate occupant injuries which may be sustained during a single-event crash with known roll mechanism. The data was obtained from the weighted National Automotive Sampling System/ Crashworthiness Data System (NASS-CDS) for calendar years 1992 to 1996. The effect of number of rollover turns, roll direction, ejection and belt usage on driver injury responses was analyzed in single-event trip-overs. Trip-overs were chosen for the analysis because they account for over 50% of rollover crashes. The number of rollovers was divided in 3 categories: ¼ to ½ turn, ¾ to 1 turn and above 1 turn. Roll direction was either roll-left or a rollright along the longitudinal axis of the vehicle. Roll-left represents a roll with the driver side leading, while a roll right is with the right front passenger side leading. In the database used in this study, there were three times more belted drivers than unbelted.

The present paper reports on a study of the HVAC energy usage for an EREV (extended range electric vehicle) implementation of a localized cooling/heating system. Components in the localized system use thermoelectric (TE) devices to target the occupant's chest, face, lap and foot areas. A novel contact TE seat was integrated into the system. Human subject comfort rides and a thermal manikin in the tunnel were used to establish equivalent comfort for the baseline and localized system. The tunnel test results indicate that, with the localized system, HVAC energy savings of 37% are achieved for cooling conditions (ambient conditions greater than 10 °C) and 38% for heating conditions (ambient conditions less than 10 °C), respectively based on an annualized ambient and vehicle occupancy weighted method. The driving range extension for an electric vehicle was also estimated based on the HVAC energy saving.

This paper describes the development and implementation of an Engine Drag Control algorithm to improve vehicle stability performance. Engine drag can occur on low and high coefficient surfaces when the driver suddenly releases the throttle. If the engine drag force becomes larger than the frictional force between the tire and the road, the tires will break loose from the surface and slip. This could induce vehicle instability especially with rear drive vehicles on low-coefficient surfaces. The EDC algorithm has been developed to provide accurate control of the wheels. EDC will help reduce the yaw rate of the vehicle and thus achieve greater vehicle stability. The paper also presents methods used to test the robustness of such a system. The purpose of the testing was to ensure that there would be no false activations of EDC under normal driving conditions and also to ensure that, when the system is active, it is mostly transparent to the driver.

Continuous Improvement activities are often based on a list of top concerns, such as highest RPN (Risk Priority Number) on the PFMEA (Process Failure Modes and Effects Analysis), warranty items, or scrap rates. But a company is in business to make a profit for its stockholders. Therefore, money should be considered, rather than just technical engineering tools and RPNs. Current PFMEA methodology (See references 1 and 2) focuses on delivering quality parts to the customer. The financial impact of various potential process problems is not considered directly. A new and extended technique called FMERA (pronounced Fuh-MAIR-uh) can identify and prioritize the process part of potential problems that have the most financial impact on an operation. Alternatives can be evaluated to maximize the financial benefits. FMERA is a method for getting the voice of the stockholder into process decisions.

The fundamental relationship between semi-solid processing and microstructure and their effect on the flow characteristics of semi-solid metals have been studied for several years. However, how the process related microstructure influences fatigue properties has not been given the same attention. This study examines the influence of process-related microstructure on the fatigue properties of semi-solid formed A357 alloys. High-solid-fraction (62% solid) and low-solid-fraction (31% and 36% solid) semi-solid formed A357 was tested in axial fatigue with a stress ratio (R) equal to -1. The high solid fraction (HSF) material had better fatigue properties than the low solid fraction (LSF) material. This is attributed to the fatigue crack initiation mechanisms, as related to the fatigue crack initiation features and the strengths of the materials.

Lead-free solders for electronics have been actively pursued since the early 1990's here and abroad for environmental, legislative, and competitive reasons. The National Center for Manufacturing Sciences (NCMS-US)1, the International Tin Research Institute (ITRI-UK)2, Swedish Institute of Production Engineering Research (IVF-Sweden)3, Japan Institute of Electronics Packaging (JIEP Japan)4, Improved Design Life and Environmentally Aware Manufacture of Electronics Assemblies by Lead-free Soldering (IDEALS-Europe)5, and, more recently, the National Electronics Manufacturing Initiative (NEMI-US)6 have been aggressively seeking lead-free solutions The automotive industry has some unique requirements that demand extensive testing of new materials and processes prior to implementation. The specific steps taken at Delphi Automotive Systems with lead-free solder will be described along with the lessons learned along the way.

Vehicle interior harmony has drawn increasing attention from customers in recent years. Kansei Engineering is an effective approach to quantify the relationship between design parameters and customer perceptions of the product. This article is a continuation of our previous study on commercial truck interior harmony. Herein, we investigated the customer perception of the visual aspects of commercial truck door interior design using classification methods. This article describes how these visual impressions are related to design elements using quantification theory, a commonly used method in Kansei Engineering. The results reveal that trim material, shape, color, window shape, and map pocket are design elements that strongly affect the perception of elegance and preferences of truck drivers. The results also showed a significant difference between the perception of the truck drivers and design engineers.