Search Results

The testing system developed will decrease the time and the costs involved in evaluating cylinder head valve bridge designs. The test uses actual data generated from engine testing to recreate the valve bridge cracks that occur during dynamometer and vehicle testing. This paper focuses on the system description, the test development, design modifications, and the test results obtained. Testing shows that this method correctly separates valve bridge designs by test cycle life using statistical methods. It is a cost effective and timely alternative to dynamometer testing.

Bench tests are often less expensive and faster than vehicle tests. However, correlation between bench tests and the engine needs to be proven, otherwise bench tests may be misleading. This investigation explored the relationships between bench wear test results and engine results from short-trip driving tests for a variety of conditions: fresh vs. used oil, different methods for assessing wear, and chemical effects such as oil contamination and differences in the fuel. There was a negative correlation between bench tests with fresh oil compared to vehicle test results with used oil, which suggests that bench wear characteristics of fresh engine oil should not be used to determine engine wear rates under the conditions tested here. Statistical analysis of bench test wear rates with used engine oil, compared to engine wear measurements, indicated that the trends were in an appropriate direction, with some scatter in the results.

The extent to which the stress history of a component is non-proportional and out-of-phase can strongly influence the accuracy of the fatigue-life prediction. Phenomenological multiaxial fatigue models are more or less accurate depending upon the extent to which the stress or strain history is non-proportional and out-of-phase. Herein, scalar measures are introduced for characterizing the non-proportional and out-of-phase extent of any stress or strain history. These scalar measures are used to characterize the stress history of a an overhead-cam cylinder-head when subjected to severe cyclic operating thermal loads.

An automatic transmission control system for clutch-to-clutch shifting systems has been developed. This enables the new General Motors Powertrain families of rear- and front-wheel drive transmissions to meet stringent cost, mass, and packaging reqiurements, while providing driveability and fuel economy improvements over the four- and five-speed transmissions that they replace. The design team utilized several new technologies and methods to robustly engineer a control system that allowed excellent first time capability and reduced calibration intensity. Innovative technical approaches were developed in several key mechatronics areas.

Implementation of engine turnoff at idle is desirable to gain improvements in vehicle fuel economy. There are a number of alternatives for implementation of the restarting function, including the existing cranking motor, a 12V or 36V belt-starter, a crankshaft integrated-starter-generator (ISG), and other, more complex hybrid powertrain architectures. Of these options, the 12V belt-alternator-starter (BAS) offers strong potential for fast, quiet starting at a lower system cost and complexity than higher-power 36V alternatives. Two challenges are 1) the need to accelerate a large engine to idle speed quickly, and 2) dynamic torque control during the start for smoothness. In the absence of a higher power electrical machine to accomplish these tasks, combustion-assisted starting has been studied as a potential method of aiding a 12V accessory drive belt-alternator-starter in the starting process on larger engines.

General Motors (GM) currently uses about 1000 different seals for manufacturing all of its automatic transmissions worldwide. In order to assure that these seals function correctly in service, a method of measuring seal performance with service fill automatic transmission fluids (ATFs) has to be specified. Along with this measure, a pass/fail criterion for the evaluation of seal performance is implemented. Due to the large number of seals that are utilized, it would be impractical to test each one with every fluid that is submitted for GM DEXRON®-III and/or Allison C4 certification. It is also very difficult to use production seals in testing, due to the irregular shapes and material combinations, which make measurement of the seal material properties difficult. Therefore, a revised test will be included in the DEXRON®-III and Allison C4 service fill specifications to evaluate the compatibility of service fill ATFs with a representative sample of seal materials used in production.

American Society for Testing and Materials (ASTM) Sequence III Engine Oil Certification Tests have been used for the past forty-five years to evaluate lubricant performance characteristics for valvetrain wear, viscosity increase, and piston deposit formation. Minimum performance standards for passenger car light duty gasoline engine oil categories are set by the International Lubricants Standardization and Approval Committee (ILSAC) (1) and the American Petroleum Institute (API) (2). This paper describes the development of the new ASTM Sequence IIIG Engine Oil Certification Test for use in evaluating the performance characteristics of engine oils meeting the next generation, low sulfur, low phosphorus, ILSAC GF-4 and API licensing requirements.

General Motors plans to introduce a hybrid version of its popular light-duty full-size (Silverado/Sierra) pickup truck. The program imperative of minimal vehicle architecture change drove a highly integrated powertrain solution. The hybrid powertrain features a novel, compact method of integrating an electric motor/generator between the largely unchanged engine and transmission, preserving their locations. From the targeted hybrid functions, power and energy specifications are derived. Specific design aspects and performance examples relating to the motor/generator packaging, torque converter, and overall vehicle driveabiltiy are discussed.

The objective of this paper is to propose that the automotive engineering “legacy” approach of assuming that vehicle electrical return paths using conductive structural components have zero (0) ohms of impedance, needs to be reviewed. The process in this review consists of the development of an equivalent circuit composed of both real (“resistive”) and reactive elements (due to inductance and capacitance). This issue needs to be addressed due to the increased complexity of electrical and electronics systems in vehicles and the use of the vehicle structural (such as chassis, frame, or bracket) components to provide a path for the return of electrical power and/or signals as a way to eliminate additional wiring manufacturing issues, cost, and weight contribution to a vehicle.

The objective of this paper is to propose a new model in the identification of a contributing factor to the generation of Radio Frequency Interference (RFI) due to the operation of a spark-ignited engine. This model incorporates parameters in the electrical operation of the ignition system components and their interaction with the engine mechanical structure, which is also used as a circuit component (the ignition system “ground”). T he model was developed as a result of analysis of numerous studies that have been conducted over the years in an attempt to identify why RFI characteristics can differ when using identical components on different engines, or locating the components in different locations on identical engines. This situation is a problem due to the resulting uncertainty with respect to the determination of what is the optimum vehicle ignition system configuration to meet all electrical and RFI or electromagnetic compatibility (EMC) requirements.

Noise radiated by engine front cover is estimated using statistical energy analysis approach. Correlations are made with the results obtained using FEM and BEM approaches. Parametric studies are also carried out to assess the regions of applicability of the SEA approach for this class of structures.

An integrated approach to modeling end of useful life of an automatic transmission fluid (ATF) has been developed. The flexible fluid life model allows either predictive or real-time calculations of the end of useful fluid life under different transmission design strategies and customer driver behaviors as reflected in operating temperatures, shift characteristics, fluid volume and fluid distribution throughout the transmission. An estimation of remaining useful fluid life is monitored using two metrics, namely bulk oxidation, as a general indicator of fluid quality, and frictional degradation, as an indicator of shift quality. As operating conditions increase in severity, ATF is subjected to conditions that may shorten its life. Using the developed technique, ATF useful life can be better predicted.

The Hydra-Matic 6T70 is General Motors first model of a new, two-variant front wheel drive (FWD) six speed automatic transmission family. The second variant is a higher capacity model, the 6T75. The transmission was co-developed with Ford Motor Company. The 6F50 is the Ford variant that aligns with the GM 6T70 transmission. Approximately eighty five percent of the hardware is shared or common between the GM and Ford transmission variants. Ford will also have a higher capacity variant the 6F55 to align with the GM 6T75. The first GM application is the Saturn Aura for the 2007 Model Year. The Ford Edge and Lincoln MKX in MY 2007 will be the first applications for the 6F50. While the Hydra-Matic and Ford FWD six-speed family was designed with two variants in mind, the designed in modularity requires only changes to the second and third axis and case housings depending on specific torque requirements. This modular design enables a tremendous amount of part sharing.

The Hydra-Matic 6L80 is General Motors first model of a new, four-variant, rear wheel drive (RWD) six speed automatic transmission family. The four variants are the 6L45, 6L50, 6L80 and 6L90. The new, high performance 6L80 will debut in 2006 model year performance vehicles, including the Chevrolet Corvette C6 and new Cadillac STS-V and XLR-V. By 2007, GM expects to use the RWD six speed family in as many as 25 different car, truck and SUV models in RWD, 4WD and all-wheel drive configurations. While the Hydra-Matic RWD six-speed family was designed with four variants, the built in modularity requires only two different basic diameters of parts and “flexing” on part width (length) depending on specific torque requirements. This built in modular design enables a tremendous amount of part sharing and part scaling. Modularity minimizes engineering resources, improves investment and piece cost, speed to market and allows for a wide bandwidth of vehicle and engine applications.

Zinc dithiophosphate, or ZDP, for over 60 years has been used as an additive in engine oils to provide wear protection and oxidation stability in an efficient and cost effective manner. Unfortunately, ZDP contains phosphorus, and phosphorus is a widely known and accepted poison of automotive catalysts and other emissions system components. Because of this, phosphorus (and ZDP) levels in automotive engine oils have been gradually reduced by about 35% over the last 10-15 years, and further reductions are likely in the future. This paper traces the history of ZDP use in automotive engine oils, and addresses the issue of how much (if any) ZDP is actually required to provide wear protection in today's, as well as yesterday's, engines. The focus in the paper is on wear (including scuffing) protection, and not on the other aspects of ZDP performance, such as providing oxidation stability of the oil.

This paper presents a newly developed integrated powertrain control system. The system coordinates the controls between engine and transmission to optimize powertrain operation for drive quality and fuel economy. This new control system uses the desired engine power as the common load variable for both engine and transmission control instead of throttle as is used in conventional powertrain controls. The main advantages to this control system are improved fuel economy and drive quality. Other advantages and a brief description of the control system will be described in more detail in the following discussion.

Rheological properties of automatic transmission fluids (ATFs) are typically characterized by their kinematic (ASTM D 445) and Brookfield (ASTM D 2983) viscosities. However, ATFs contain polymeric viscosity modifiers, which often result in non-Newtonian fluid behavior as the polymers align and stretch under the shear stresses experienced in automatic transmissions. Therefore, the standard rheological tests, which are normally run under low shear stresses, may not adequately characterize an ATF's flow properties under the operating conditions of the automatic transmission. This study was designed to characterize the rheological properties of ATFs containing different amounts of viscosity modifiers, different base oil types and different levels of permanent shear stability under the shear and temperature conditions which exist in automatic transmissions.

Since the mid-1990's, original equipment manufacturers (OEMs) of automobiles have been implementing torque converter clutches in automatic transmissions with a continuous, controlled slip mode, in order to improve the fuel economy of their vehicles. These Continuously Slipping Torque Converter Clutches (CSTCCs) are prone to an undesirable phenomenon commonly called shudder. This phenomenon has been attributed to specific shapes or slopes in the friction coefficient versus sliding speed curve of the fluid/clutch interface. Here, a method is explained that was developed to be able to screen fluids for shudder tendency, both in fresh and used states. Also included is a description of the reason for implementing CSTCCs, some background on shudder, and supporting data showing how the test method can distinguish between fluids that have different shudder tendencies.

Active Hall Effect Sensors are used in numerous automotive applications where direction, position, and speed sensing capabilities are required. The primary usage of these devices is in the areas of engine and transmission controls as well as ABS speed monitoring systems. To reliably employ these sensors in such applications requires a thorough understanding of the device electronics and how this component interprets the magnetic fields produced by a ferromagnetic target. The traditional methods involving the construction and test of prototype sensors and targets have been costly, time consuming, and rarely resulted in a robust design. To resolve this problem General Motors Powertrain and Ansoft Corporation have jointly developed the capability to accurately model active Hall Effect Sensors.

Principal Component Analysis (PCA) is a powerful statistical technique used for understanding variation in the observed data and decomposing variation along eigenvectors, known as Principal Components (PCs), by considering variance-covariance structure of the data. Traditionally, eigenvectors that contain most of the variation or information are selected to reduce variables in data reduction. Eigenvalues of low magnitude are considered to be noise and often, not included in the dataset to accomplish dimensional reduction. Analogously, in Principal Component Regression (PCR), PCs with large eigenvalues are selected without considering correlation between the source variables and the dependent response. This inherent deficiency may lead to inferior regression modelling. While addressing this issue, an alternative to PCR is developed and proposed in this paper. In this method, a principal component associated with zero eigenvalue is termed Trivial Principal Component (TPC).