Search Results

This paper attempts to assess the benefits of a unique distributed propulsion concept, known as the Multi-Gas Generator Fan (MGGF) system, over conventional turbofan engines on civilian vertical takeoff and landing (VTOL) applications. The MGGF-based system has shown the potential to address the fundamental technical challenge in designing a VTOL aircraft: the significant mismatch between the power requirements at lift-off/hover and cruise. Vehicle-level performance and sizing studies were implemented using the Grumman Design 698 tilt-nacelle V/STOL aircraft as a notional personal air vehicle (PAV), subjected to hypothetical single engine failure (SEF) emergency landing requirements and PAV mission requirements.

As gas prices and climate change become the preeminent issues of today, more research effort is being directed towards the development of cheaper and cleaner alternative energy sources. These efforts have been further complemented with research into the applicability of these sources to air, land and sea borne vehicles. In this report a notional C-172R general aviation aircraft is retrofitted with a PEM power plant as a case-study. Lower bounds for useful load and range are set in such a way that the results can be useful in determining how much improvement in the technology would be required to power a useful general aviation vehicle. It is seen that even at the predicted 2015 fuel cell technology level (per US Department of Energy projections), PEM systems would still be infeasible for this vehicle due to low specific power. Further investigation revealed that a PEM-battery hybrid system had better chances of feasibility.

A fuel cell which uses pure hydrogen sulfide as fuel and a solid electrolyte of ceria stabilized with yttria (YSC) has been proposed, with the configuration H2S, Pt/YSC/Pt, O2 (air), operating at temperatures of 600 to 800° C. Initial experiments will use platinum electrodes, with subsequent runs using various perovskite type electrodes. The YSC electrolye system exhibits better ionic conductivity than the more familiar YSZ electrolytes, and thus the fuel cell will operate at a lower temperature range. Cell component manufacture, cell experiments, and analytical techniques are discussed.

The recent development of electric vehicles creates a new area of interest regarding their potential impacts on natural resource and energy networks. Water consumption is of particular interest, as water scarcity becomes a growing problem in many regions of the world. Water usage can be traced to the production of gasoline, as well as electricity, for regular operation of these vehicles. This paper focuses on the development of a framework to analyze the amount of water consumed in the operation of both conventional and electric vehicles. Using the Systems Modeling Language, a model was developed based on the water consumed directly in energy generation and processing as well as water consumed in obtaining and processing a vehicle's fuels. This model and framework will use the above water consumption breakdown to examine conventional and electric vehicles in metropolitan Atlanta to assess their impacts on that and other urban networks.

Hybrid-electric powertrains for passenger vehicles and light trucks are generally being designed with two different configurations described as follows: The Toyota Hybrid System, THS-II, implemented in the 2004 Prius, the Lexus 400-H, and the Ford Hybrid Escape, is a power-split approach involving two electric machines and an internal combustion engine (ICE) mechanically coupled by a three-shaft planetary gear train. The second leading approach is a parallel hybrid-electric powertrain that generally includes a single electric machine and an ICE with a mating multi-ratio transmission. These parallel configurations are further divided as weak parallel and strong parallel. Honda uses a weak parallel powertrain in their Insight and Hybrid Civic. At Georgia Tech a strong (full), split-parallel hybrid powertrain has been implemented in a Ford Explorer. The vehicle is referred to as the Model GT.

General Motors has introduced a Two-Mode Transmission (2-MT) that provides significant improvements over the Toyota THS-II transmission. These improvements are achieved by employing additional planetaries with clutches and brakes to switch from a Mode-1 to Mode-2 as vehicle speed increases. In addition the 2-MT has four fixed-gear ratios that provide for a purely mechanical energy path from the IC engine to the driven wheels with the electric machines also able to provide additional driving torque. The purpose of this present paper is to extend the methodology in a previous paper [1] to include the 2-MT, thereby presenting an analytic foundation for its operation. The main contribution in this analysis is in the definition of dimensionless separation factors, defined in each mode that govern the power split between the parallel mechanical and electrical energy paths from the IC engine to the driven wheels.

Compressed natural gas (CNG) is an attractive, alternative fuel for spark-ignited (SI), internal combustion (IC) engines due to its high octane rating, and low energy-specific CO2 emissions compared with gasoline. Directly-injected (DI) CNG in SI engines has the potential to dramatically decrease vehicles’ carbon emissions; however, optimization of DI CNG fueling systems requires a thorough understanding of the behavior of CNG jets in an engine environment. This paper therefore presents an experimental and modeling study of DI gaseous jets, using methane as a surrogate for CNG. Experiments are conducted in a non-reacting, constant volume chamber (CVC) using prototype injector hardware at conditions relevant to modern DI engines. The schlieren imaging technique is employed to investigate how the extent of methane jets is impacted by changing thermodynamic conditions in the fuel rail and chamber.

This paper presents a comparative analysis of two different power-split hybrid-electric vehicle (HEV) powertrains using backward-looking simulations. Compared are the front-wheel drive (FWD) Toyota Hybrid System II (THS-II) and the FWD General Motors Allison Hybrid System II (GM AHS-II). The Toyota system employs a one-mode electrically variable transmission (EVT), while the GM system employs a two-mode EVT. Both powertrains are modeled with the same assumed mid-size sedan chassis parameters. Each design employs their native internal combustion (IC) engine because the transmission's characteristic ratios are designed for the respective brake specific fuel consumption (BSFC) maps. Due to the similarities (e.g., power, torque, displacement, and thermal efficiency) between the two IC engines, their fuel consumption and performance differences are neglected in this comparison.

Using measurable physical input variables, an implementable control algorithm for parallel architecture plug-in and non-plug-in hybrid electric vehicle (PHEV and HEV) powertrains is presented. The control of the electric drive is based on an algebraic mapping of the accelerator pedal position, the battery state-of-charge (SOC), and the vehicle velocity into a motor controller input torque command. This mapping is developed using a sequential linearization control (SLC) methodology. The internal combustion engine (ICE) control uses a modified accelerator pedal to throttle plate angle using an adjustable gain parameter that, in turn, determines the sustained battery SOC. Searches over an admissible control space or the use of pre-defined look-up tables are thus avoided. Actual on-road results for a Ford Explorer with a through-the-road (TTR) hybrid powertrain using this control methodology are presented.

A plug-in hybrid electric vehicle (PHEV) design with design parameters electric motor size, engine size, battery capacity, and battery chemistry type, is optimized with minimum cost as a measure of merit. The PHEV is required to meet a fixed set of performance constraints consisting of 0-60 mph acceleration, 50-70 mph acceleration, 0-30 mph acceleration in all electric operation, top speed, grade ability, and all electric range. The optimization is carried out for values of all electric range of 10, 20, and 40 miles. The social and economic impacts of the optimum designs in terms of reduced gasoline consumption and carbon emissions reduction are calculated. Argonne National Laboratory's Powertrain Systems Analysis Toolkit is used to simulate the performance and fuel economy of the PHEV designs. The costs of different PHEV components and the present value of battery replacements over the vehicle's life are used to determine the design's drivetrain cost.

Test methods and data acquisition system specifications are described for measurements of the energy consumption of the control system of a servo-pump continuously variable transmission (CVT). Dynamic measurements of the power consumption of the servo-pump CVT control system show that the control system draws approximately 18.9 W-hrs of electrical energy over the HWFET cycle and 13.6 W-hrs over the 505 cycle. Sample results are presented of the dynamic power consumption of the servo-pump system under drive cycle conditions. Steady state measurements of the control power draw of the servo-pump CVT show a peak power consumption of 271 W, including lubrication power. The drive-cycle averaged and steady state energy consumption of the servo-pump CVT are compared to conventional CVT pump technologies.

This paper describes a machine to quarry construction material, sinter walls, and assemble future space station modules. In prior work, we explored the solar energy requirements to build a 50m diameter, 50m high, cylindrical module out of pulverized rock from a Near-Earth Object, using tailored radio wave fields. In this paper, we describe the issues in the conceptual design of the robotic construction machines. The 4-legged Rock breaker is designed to fit the payload bay of a modern heavy-lift booster to reach Low Earth Orbit, and primary solar-sail propulsion for most of its journey. It uses beamed microwave energy for its cutting operations. Rotating, telescoping arms use integrated laser/plasma jet cutter arrays to dig trenches in spiral patterns which will form blocks of material. Cut blocks are sent into a toroidal cloud of material for use in the force field tailoring for automatic module formation.

This paper presents a forward-looking simulation (FLS) approach for the front wheel drive (FWD) General Motors Allison Hybrid System II (GM AHS-II). The supervisory control approach is based on a dynamic programming-informed Equivalent Cost Minimization Strategy (ECMS). The controller development uses backward-looking simulations (BLS), which execute quickly by neglecting component transients while assuming exact adherence to a specified drive cycle. Since ECMS sometimes prescribes control strategies with rapid component transients, its efficacy remains unknown until these transients are modeled. This is addressed by porting the ECMS controller to a forward-looking simulation where component transients are modeled in high fidelity. Techniques of implementing the ECMS controller and commanding the various power plants in the GM AHS-II for FLS are discussed.

The Georgia Tech FutureTruck Team has designed a strong parallel split-hybrid powertrain for the model year 2002 Ford Explorer SUV. The modified powertrain uses a Lincoln LS 3.0L, V-6, DOHC, aluminum engine driving the rear axle. An AC-150 from AC Propulsion is coupled to the front wheels through a 3.75:1 Auburn Gear speed reducer. This split-hybrid structure fits well into the Explorer and is to manufacture. The interior cabin has been maintained in a stock configuration by carefully integrating the added instrumentation and electric drive controls into the dash and console. The toque-blending hybrid electric control is designed to be charge sustaining such that the refueling procedures match those of the stock vehicle. When fully operational, this powertrain is expected to yield a net 25% increase in fuel efficiency while lowering emissions without any sacrifice in customer acceptability.

This paper presents a detailed design study and associated considerations supporting the development of high-performance plug-in hybrid electric vehicles (PHEVs). Due to increasingly strict governmental regulations and increased consumer demand, automotive manufacturers have been tasked with the reduction of fuel consumption and greenhouse gas (GHG) emissions. PHEV powertrains can provide a needed balance in terms of fuel economy and vehicle performance by exploiting regenerative braking, pure electric vehicle operation, engine load-point shifting, and power-enhancing hybrid traction modes. Thus, properly designed PHEV powertrains can reduce fuel consumption while increasing vehicle utility and performance.

In this paper, we discuss our experiences with applying an approach called Activity-Based Life-Cycle Assessment (LCA) in industrial settings. In contrast to other Life-Cycle Assessment approaches, we have taken modern cost management practices such as Activity Based Costing as a basis for our approach to environmental impact assessment. The resulting method, Activity-Based LCA, is an extension of Activity-Based Costing as it handles costs, energy consumption and waste generation simultaneously under the presence of uncertainty in a single framework.

General Motors has recently developed a front-wheel drive version of its two planetary two-mode transmission (2-MT) for a hybrid-electric vehicle powertrain [1]. This newer transmission includes two planetary gears with two transfer clutches and two braking clutches. With activation of designated pairs of these four clutches, four fixed-gear ratios between the transmission's input shaft and output shaft are obtained. In addition, activation of specific individual clutches gives two modes of operation whereby the IC engine speed is decoupled from the vehicle velocity thus providing an electrical continuously variable transmission (ECVT). This present paper extends the power-split analysis in [2] by deriving a safe-operating region (SOR) in the plane of IC engine speed vs. vehicle velocity for the four fixed-gear and two ECVT modes. This SOR is bounded by the speed limitations of the 2-MT components. Similar results are presented for the Toyota Hybrid System II (THS-II) transmission.

Modeling and simulation are commonly used in all stages of the design process. This is particularly vital to the success of systems engineering projects where the system under consideration is complex and involves interactions between many interdisciplinary subsystems. In the refining stages of the design process (after concept selection), models and simulations can be used to refine and optimize a system with respect to the decision maker’s objectives. In this paper, a dynamic model of a hydraulic backhoe serves as a test-bed for a large-scale sensitivity analysis and subsequent optimization of the most significant design parameters. The model is optimized under uncertainty with respect to a multi-attribute utility function that includes fuel consumption, cost of the key components, and machine performance.

In this study we identify components of a typical biodiesel fuel and estimate both their individual and mixed thermo-physical and transport properties. We then use the estimated mixture properties in computational simulations to gauge the extent to which combustion is modified when biodiesel is substituted for conventional diesel fuel. Our simulation studies included both conventional diesel combustion (DI) and premixed charge compression ignition (PCCI). Preliminary results indicate that biodiesel ignition is significantly delayed due to slower liquid evaporation, with the effects being more pronounced for DI than PCCI. The lower vapor pressure and higher liquid heat capacity of biodiesel are two key contributors to this slower rate of evaporation. Other physical properties are more similar between the two fuels, and their impacts are not clearly evident in the present study.

Power-split hybrid-electric vehicles (HEVs) employ two power paths between the internal combustion (IC) engine and the driven wheels routed through gearing and electric machines (EMs) composing an electrically variable transmission (EVT). The EVT allows IC engine control such that rotational speed can be independent of vehicle speed at all times. By breaking the rigid mechanical connection between the IC engine and the driven wheels, the EVT allows the IC engine to operate in the most efficient region of its characteristic brake specific fuel consumption (BSFC) map. If the most efficient IC engine operating point produces more power than is requested by the driver, the excess IC engine power can be stored in the energy storage system (ESS) and used later. Conversely, if the most efficient IC engine operating point does not meet the power request of the driver, the ESS delivers the difference to the wheels through the EMs.