Search Results

A dual piston Variable Compression Ratio (VCR) engine has been newly developed. This compact VCR system uses the inertia force and hydraulic pressure accompanying the reciprocating motion of the piston to raise and lower the outer piston and switches the compression ratio in two stages. For the torque characteristic enhancement and the knocking prevention when the compression ratio is being switched, it is necessary to carry out engine controls based on accurate compression ratio judgment. In order to accurately judge compression ratio switching timing, a control system employing the Hidden Markov Model (HMM) was used to analyze vibration generated during the compression ratio switching. Also, in order to realize smooth torque characteristics, an ignition timing control system that separately controls each cylinder and simultaneously performs knocking control was constructed.

A hybrid simulation model in the transient bench was developed to realize the characteristics of the transient behavior and the fuel economy equivalent to that of a real vehicle. The motors and the batteries that were main components of the hybrid vehicle system were simulated as constructive modules, the functions of which have the integrated control and the input/output (I/O) function with real components. This model enabled us to accommodate a variety of auxiliary (AUX) I/O flexibly. The accuracy of the model was verified by the transient characteristics of the engine and the fuel economy result through correlation with a mass-produced vehicle. Furthermore, the flexibility of the model to a variety of AUX I/O was examined from the simulation test of the vehicle equipped with the waste heat recovery (WHR) system.

The technology to estimate engine load using the amplitude of crankshaft angular velocity variation during a cycle, which is referred to as “Δω (delta omega)”, in a four-stroke single-cylinder gasoline engine has been established in our former studies. This study was aimed to apply this technology to the spark advance control system for small motorcycles. The cyclic variation of the Δω signal, which affects engine load detection accuracy, was a crucial issue when developing the system. To solve this issue, filtering functions that can cope with various running conditions were incorporated into the computation process that estimates engine loads from Δω signals. In addition, the system made it possible to classify engine load into two levels without a throttle sensor currently used. We have thus successfully developed the new spark advance system that is controlled in accordance with the engine speed and load.

The Vehicle Stability Assist (VSA) system can generate sufficient forces to rapidly change the vehicle's motion. We can use this capability to effectively control the vehicle's behavior, but we must pay careful attention to ensure its reliability. The VSA system should be precisely tuned for each vehicle's characteristics in order to satisfactorily control performance without any unnecessary intervention or any excessive warnings. Usually extensive field tests are necessary to precisely tune the VSA system. This paper presents a practical method to tune the VSA system with Hardware-In-the-Loop (HIL) simulations in the final stage of its development. Due to the application of this procedure, both high control capabilities and reliability of the VSA system can be achieved.

The aim discussed in this paper is to show a technique to predict loads input to the wheels, essential to determining input conditions for evaluation of suspension durability, by means of full vehicle simulations using multi body analysis software Adams/Car. In this process, model environments were built to enable reproduction of driving modes, and a method of reproducing the set-up conditions of a durability test vehicle was developed. As the result of verification of the accuracy of the simulations in the target driving modes, good correlation for waveforms can be confirmed. And also confirm a good correlation in relation to changes of input load due to changes in suspension specifications.

Using stabilizing yaw-moment diagrams, the authors analyzed three methods of active chassis control for their effect and effective ranges during cornering maneuvers. The following results were obtained: controlling the transverse distribution of driving and braking forces cancels the changes in a vehicle's dynamic characteristics caused by acceleration and deceleration. Controlling the distribution of roll stiffness is only effective in ranges with high lateral acceleration, and the effect varies depending on the longitudinal weight distribution. Controlling the rear wheel steering angle is most effective in a range with a small side slip angle, but this effect decreases with an increase in the angle, especially during deceleration.

In conventional electronically controlled fuel injection systems, when the battery is inadequately charged, the small amount of electric power generated from the alternator by the kick starter operation is consumed by all electrical loads including the battery. This causes a voltage drop, hence the fuel injection system does not function due to a power shortage. To eliminate the power shortage, an installed relay circuit opens all electric loads other than the fuel injection system. This allows the fuel injection system to use all the electric power generated by the kick starter operation aided through using an additionally incorporated condenser. This type of electric power control system has been incorporated into the ECU. Thus, the control system has been realized that permits starting of an engine by using the kick-starter even when the battery is completely discharged.

Prediction of drowsiness based on an objective measure is demanded in machine and vehicle operations, in which human error may cause fatal accidents. Recently, we focused on the pupil which is controlled by the autonomic nervous system, easily and non-invasively observable from the outside of the body. Prior to the large low frequency pupil-diameter fluctuation, which is known to associate with drowsiness, a Gradual Miosis was observed in most subjects. During this miosis period, the subjects were not yet aware of their drowsiness. We have developed a software system which automatically detects the Gradual Miosis in real time.

In this paper, a newly developed Active Noise Control (ANC) system is introduced, that effectively reduces road noise, which becomes a major issue with electrified vehicles, and that enhances vehicle interior sound levels matching seamless acceleration by electric drive. Conventionally, reducing road noise using ANC requires numerous sensors and speakers, as well as a processor with high computing power. Therefore, the increase in system cost and the complexity of the system are obstacles to its spread. To overcome these issues, this system is developed based on four concepts. The first is a modular system configuration with unified interface to apply to various vehicle types and grades. The second is the integration and optimal placement of noise source reference sensors to achieve both reduction in number of parts and noise reduction performance.

When a vehicle is in motion, noise is generated in the cabin that is composed of noise in multiple narrow-frequency bands and caused by input from the road surface. This type of noise is termed low-frequency-band road noise, and its reduction is sought in order to increase occupant comfort. The research discussed in this paper used feedback control technology as the basis for the development of an active noise control technology able to simultaneously reduce noise in multiple narrow-frequency bands. Methods of connecting multiple single-frequency adaptive notch filters, a type of adaptive filter, were investigated. Based on the results, a method of connecting multiple filters that would mitigate mutual interference caused by different controller transmission characteristics was proposed.

A new brake system, able to make efficient use of regenerative braking while maintaining excellent brake feel, has been developed to increase the fuel economy of hybrid vehicles. A hydraulic servo was used as a base to enable mechanical operation of the service brakes; solenoid valves and brake fluid pressure sensors were added to this base to make it possible to control brake line pressure as demanded. The use of a stroke simulator in the hydraulic servo prevents brake feel from being affected by the control of the brake pressure. In addition, high-accuracy brake pressure control that functions cooperatively with the regenerative brakes is enabled, resulting in stable braking effectiveness.

A new control system using O₂ feedback control has been developed as an alternative to intake air pressure sensors. This control method uses the operational condition compensation coefficient Kbu. This coefficient encompasses the state of the engine and environmental conditions such as atmospheric pressure, and corrects fuel injection in response to changes in these factors. Kbu makes it possible to control the amount of fuel injection without depending on an intake air pressure sensor. It also makes it possible to carry out the appropriate air-fuel ratio correction even at times when O₂ feedback control is not operating, such as the cold period, when the engine is first started, or during transient operation, by using Kbu values recorded in the Engine Control Unit (henceforth ECU).

The mounting of lithium-ion batteries (LIB) in hybrid electric vehicles (HEV) calls for the configuration of highly robust control systems. When mounting LIBs in the vehicle, it is important to accurately ascertain and precisely control the state of the battery. In order to achieve high durability, it is important to configure highly reliable systems capable of dependably preventing overcharging as well as to have control technology based on software that can contribute to extended battery life. The system configuration applies an overcharge prevention system that uses voltage detection with an emphasis on reliability. Furthermore, a method for varying the range of state of charge (SOC) control in the vehicle according to the battery state is implemented to assure durability. In order to achieve this, battery-state detection technology was developed for the purpose of correctly detecting and judging the battery state.

Conventionally, it has not been possible to evaluate current and temperature in power control units (PCU) for hybrid electric vehicles (HEV) during vehicle operation without using an actual permanent magnet synchronous motor (PMSM). The research discussed in this paper developed a motor emulator to take the place of an actual motor, making it possible to conduct tests for the evaluation of current and temperature in PCU during vehicle operation without the need to use a motor. The motor emulator is provided with a hardware-in-the-loop (HIL) simulator that calculates motor models at high speed using a field programmable gate array (FPGA). The developed system models the motor in detail via the HIL simulator, while a 3-phase current generator accurately reproduces the transient current in the PCU during vehicle operation.

A multi-use road simulator for reproducing various road loads on motorcycles and buggies has been developed on a test bench by using computer-controlled hydraulic actuators. The device is controlled by a low-priced personal computer and an interface system with custom software. An unique feature is the capability to simulate loads related to such phenomena as the bottoming of suspension and the movement of a telescopic type front fork on the road.

Recently, automotive emission regulations are being further tightened, such as the Tier III/LEV III in the U.S. As a result, reducing cost of after-treatment systems to meet these strict regulations has become an urgent issue, and then the demand for high-precision air-fuel ratio (A/F) control which can achieve this cost reduction is high [1]. On the other hand, in order to meet rapidly changing market needs, it is becoming difficult to keep enough development periods that enable sufficient calibration by trial-and-error, such as feedback-gain calibration. This leads to an increase in three-way catalytic converter costs in some cases. For these reasons, it is necessary to construct control system that can make full use of hardware capabilities, can shorten development periods regardless of the skill level of engineers.

New valve control system (HYPER VTEC:Variable Valve Timing and Lift Electronic Control System) having valve inactive mechanism which engine power is made to be united to the environment conservation was developed for motorcycle engines of sport type having higher engine speed. Mass increase in the valve operating system of this system is kept to a minimum with a compact, simple mechanism. The system enables high engine speed up to 13,500 rpm without abnormal motion of valves, having high reliability and durability. In addition, the valve control system has the enhancement of fuel economy and the effect of decreasing the intake and exhaust system sound during 2-valve operation. The switching mechanism part of the operating valve number was manufactured by cold forging, and has decreased costs. This system has been adopted to the sport type motorcycle CB400SF for domestic model in 1999.

A motor-assist system has been developed and employed for the "Insight' hybrid car. The system consists of an internal combustion engine as the primary power source, with an electric motor placed around the engine's crankshaft. Such construction reduces the system's volume significantly and offers more flexibility for the power plant layout. The system's functions include regeneration during braking, an idle stop mechanism, driving power assistance, and power supply for the 12V electrical system. A proper energy management method for various driving modes has been established by combining these functions, and fuel economy is significantly improved as a result. As another control feature, an active motor vibration control system compensates the idling vibration that is unique to three-cylinder engines.

The change in the aerodynamic lift force (henceforth CL) by heave motion is discussed in this paper in order to clarify the effect of aerodynamic characteristics on the vehicle dynamic performance. We considered that phenomenon in actual car running at 160km/h and 1Hz heave frequency. Using a towing tank to change its water from the air to the working fluid to more easily observe this phenomenon. That makes possible to observe the same phenomenon with reduced velocity and small models under same Strouhal number condition. This method can be reducing vehicle speed to 3m/s (1/15 actual) and frequency to 0.2Hz (1/5 actual) in case using 40% scaled model. The results of these tests showed that unsteady CL is proportional to heave motion. These results showed the proportional relationship between unsteady CL and heave motion. The formularization of unsteady CL made it possible to introduce shape coefficients to vehicle dynamics simulations as functions of heave velocity.

We have successfully developed a system to estimate Indicated Mean Effective Pressure (hereafter "IMEP") by detecting the crankshaft angular velocity variation during one cycle of a four-stroke single-cylinder gasoline engine. The system has been commercially applied to the spark-ignition timing control system for small-displacement motorcycle engines. The determined amplitude of crankshaft angular velocity variation during one cycle is defined as "delta omega (Δω)." The relationship between Δω and IMEP has been experimentally examined using engine unit bench tests and actual motorcycles. From the experimental results, it was confirmed that Δω represents IMEP. This paper discusses the experimental study on the estimation of IMEP using crankshaft angular velocity variation.