Search Results

The use of methane as supplement to liquid fuel is one of the solution proposed for the reduction of the internal combustion engine pollutant emissions. Its intrinsic properties as the high knocking resistance and the low carbon content makes methane the most promising clean fuel. The dual fuel combustion mode allows improving the methane combustion acting mainly on the methane slow burning velocity and allowing lean burn combustion mode. An experimental investigation was carried out to study the methane-gasoline dual fuel combustion. Methane was injected in combustion chamber (DI fuel) while gasoline was injected in the intake manifold (PFI fuel). The measurements were carried out in an optically accessible small single-cylinder four-stroke engine. It was equipped with the cylinder head of a commercial 250 cc motorcycles engine representative of the most popular two-wheel vehicles in Europe.

Nowadays, alcohol fuels are of increasing interest as alternative transportation biofuels even in compression ignition engines because they are oxygenated and producible in a sustainable way. In this paper, the experimental research activity was conducted on a single cylinder research engine provided with a modern architecture and properly modified in a dual-fuel (DF) configuration. Looking at ethanol the as one of the future environmental friendly biofuels experimental campaign was aimed to evaluate in detail the effect of the use of the ethanol as port injected fuel in diesel engine on the size, morphology, reactivity and chemical features of the exhaust emitted soot particles. The engine tests were chosen properly in order to represent actual working conditions of an automotive light-duty diesel engine. A proper engine Dual-Fuel calibration was set-up respecting prefixed limits on in-cylinder peak firing pressure, cylinder pressure rise, fuel efficiency and gaseous emissions.

In the last years, even more attention was paid to the alternative fuels which can allow both reducing the fuel consumption and the pollutant emissions. Among gaseous fuels, methane is considered one of the most interesting in terms of engine application. It represents an immediate advantage over other hydrocarbon fuels leading to lower CO₂ emissions; if compared to gasoline, CH₄ has wider flammable limits and better anti-knock properties, but lower flame speed. The addition of H₂ to CH₄ can improve the already good qualities of methane and compensate its weak points. In this paper a comparison was carried out between CH₄ and different CH₄/H₂ mixtures. The measurements were carried out in an optically accessible small single-cylinder, Port Fuel Injection spark ignition (PFI SI), four-stroke engine. It was equipped with the cylinder head of a commercial 250 cc motorcycle engine representative of the most popular two-wheel vehicles in Europe.

The objective of this paper is the evaluation of the effect of the fuel properties and the comparison of a PFI and GDI injection system on the performances and on particle emission in a Spark Ignition engine. Experimental investigation was carried out in a small single cylinder engine for two wheel vehicles. The engine displacement was 250 cc. It was equipped with a prototype GDI head and also with an injector in the intake manifold. This makes it possible to run the engine both in GDI and PFI configurations. The engine was fuelled with neat gasoline and ethanol, and ethanol/gasoline blends at 10% v/v, 50% v/v and 85% v/v. The engine was equipped of a quartz pressure transducer that was flush-mounted in the region between intake and exhaust valves. Tests were carried out at 3000 rpm and 4000 rpm full load and two different lambda conditions. These engine points were chosen as representative of urban driving conditions.

This paper reports experiments on a single-cylinder direct-injection compression ignition engine operating in premixed charge compression ignition (PCCI) combustion mode. The engine was fuelled with pure rapeseed methyl ester (RME) and bio-ethanol. RME was injected in the combustion chamber by common rail (CR) injection system at 800 bar and bio-ethanol in the intake manifold by commercial port fuel injection system at 3.5 bar. The effects of different percentage of bio-ethanol were studied by means of both the in-cylinder heat release analysis and the high-speed UV-visible chemiluminescence visualization. The pollutant formation and exhaust emissions of the engine operating in dual fuel mode were evaluated. The increase of the bio-ethanol content improved the brake thermal efficiency slightly even if the brake fuel consumption increased. However, the choice to inject two biofuels decreases both the smoke opacity and NOx concentration.

Multi-fuel operation is one of the main topics of investigative research in the field of internal combustion engines. Spark ignition (SI) power units are relatively easily adaptable to alternative liquid-as well as gaseous-fuels, with mixture preparation being the main modification required. Numerical simulations are used on an ever wider scale in engine research in order to reduce costs associated with experimental investigations. In this sense, quasi-dimensional models provide acceptable accuracy with reduced computational efforts. Within this context, the present study puts under scrutiny the assumption of spherical flame propagation and how calibration of a two-zone combustion simulation is affected when changing fuel type. A quasi-dimensional model was calibrated based on measured in-cylinder pressure, and numerical results related to the two-zone volumes were compared to recorded flame imaging.

Uncertainty of fuel supply in the energy sector and environmental protection concerns have motivated studies on clean and renewable alternative fuels for vehicles as well as stationary applications. Among all fuel candidates, hydrogen is generally believed to be a promising alternative, with significant potential for a wide range of operating conditions. In this study, a comparison was carried out between CH4, two CH4/H2 blends and two mixtures of CO and H2, the last one taken as a reference composition representative of syngas. It is imperative to fully understand and characterize how these fuels behave in various conditions. In particular, a deep knowledge of how hydrogen concentrations affect the combustion process is necessary, given that it represents a fundamental issue for the optimization of internal combustion engines. To this aim, flame morphology and combustion stability were studied in a SI engine under lean burn conditions.

Hydrogen (H₂) added to natural gas (NG), improves the combustion process of the air-fuel mixture. This gives the potentiality to develop engines with better performance and lower environmental impact. In any case how hydrogen is produced represents a crucial aspect. In general, if H₂ is produced utilizing fossil fuels and not renewable or nuclear sources, the environmental benefit of CO₂ reduction could be reduced. In this paper two engines, a light-duty (LD) and a heavy-duty (HD), were tested in stoichiometric conditions. The engines were fuelled with NG and with two blends of NG with a 20% and a 40% by volume of H₂, respectively named NG/H₂ 20% and NG/H₂ 40%. The light-duty engine was tested at different loads and speeds, with spark advance set by the electronic control unit (ECU). The ECU actuated a retarded ignition, especially at low load. With the heavy-duty engine, the tests were carried out only at high load.

Great efforts have been paid to improve engine efficiency as well as to reduce the pollutant emissions. The direct injection allows to improve the engine efficiency; on the other hand, the GDI combustion produces larger particle emissions. The properties of fuels play an important role both on engine performance and pollutant emissions. In particular, great attention was paid to the octane number. Oxygenated compounds allow increasing gasoline's octane number and play an important role in PM emission reduction. In this study was analyzed the effect of fuels with different RON and with ethanol and ethers content. The analysis was performed on a small GDI engine. Two operating conditions, representative of the typical EUDC cycle, were investigated. Both the engine performance and the exhaust emissions were evaluated. The gaseous emissions and particle concentration were measured at the exhaust by means of conventional instruments.

Nowadays, alcoholic fuels gain increased interest as alternative transportation biofuel even in compression ignition engines due to the fact that they contain oxygen and can be produced in a sustainable way. Furthermore, due to their lower CN (Cetane Number) they suit better for premixed combustion applications. Experimental research was conducted on a single cylinder engine provided with modern engine architecture modified for DF (Dual-Fuel) purposes. The authors have investigated the use of ethanol in a DF engine in order to exploit its well-known advantages in premixed combustion mode. The DF approach appears to be a promising solution because it permits flexible control of the premixed fuel fraction regardless from the operating conditions. This improves the exploitation of the ethanol potential according the engine working conditions.

Ethanol is the most promising alternative fuel for spark ignition (SI) engines, that is blended with gasoline, typically. Moreover, in the last years great attention is paid to the dual fueling, ethanol and gasoline are injected simultaneously. This paper aims to analyze the better methods, blending or dual fueling in order to best exploit the potential of ethanol in improving engine performance and reducing pollutant emissions. The experimental activity was carried out in a small displacement single cylinder engine, representative of 2-3 wheel vehicle engines or of 3-4 cylinder small displacement automotive engines. It was equipped with a prototype gasoline direct injection (GDI) head. The tests were carried out at 3000, 4000, and 5000 rpm full load. The investigated engine operating conditions are representative of the European homologation urban driving cycle.

This paper investigates abnormal combustion during the cranking phase of spark-ignition small engines, specifically the occurrence of backfire at the release of the starter motor during kickback. The research focusses on the influence of fuel composition, mainly in terms of ethanol percentage, on backfire occurrence. Interest in this abnormal combustion is growing due to the increased use of fuels with different chemical-physical properties with respect to gasoline. Moreover, this issue will become even more topical due to the implementation of simple control and fuel supply systems on low cost-engines, which are widely used in developing countries. Experimentation was carried out in an optically accessible engine derived from a 4-stroke spark ignition engine for two-wheel vehicles. The test bench was instrumented and adapted in order to simulate the engine conditions that lead to anomalous ignition in the intake duct (backfire) during the reverse rotation of the engine (kickback).

Characterization of combustion parameters of gaseous fuels is the main objective of a novel experimental laboratory, which recently became operational at Istituto Motori: the "Device for Hydrogen-Air Reaction Mode Analysis" (DHARMA in brief) project is meant to generate a systematic database on the burning properties of CH₄, H₂ and other species of interest, in conditions typical of i.c. engines. The experimental setup is based upon an optically accessible cylindrical bomb, where tests are carried out on spherical expanding flames. High-speed shadowgraph is used to record the flame growth and to infer laminar burning parameters. Thorough details are given of the experimental apparatus and the data analysis. Experimental data are presented for the combustion in air of CH₄ and of CH₄/H₂ mixtures: the percentage of hydrogen was 20% and 30% (vol.).

In this paper the methane-gasoline dual fuel combustion was investigated. Gasoline was injected in the intake manifold (PFI fuel), while methane was injected in the combustion chamber (DI fuel), in order to reproduce a stratified combustion. The combustion process and the related engine performance and pollutant emissions were analyzed. The measurements were carried out in an optically accessible small single-cylinder four-stroke engine. It was equipped with the cylinder head of a commercial 250 cc engine representative of the most popular two-wheel vehicles in Europe. Optical measurements were performed to analyze the combustion process with high spatial and temporal resolution. In particular, optical techniques based on 2D-digital imaging were used to follow the flame front propagation and the soot and temperature concentration in the combustion chamber.

This paper reports an experimental and numerical investigation of the spray structure development for pure gasoline fuel and two different ethanol-gasoline blends (10% and 85% ethanol). A numerical methodology has been developed to improve the prediction of the pure and blends fuel spray. The fuel sprays have been simulated by means of a 3D-CFD code, adopting a multi-component approach for the fuel simulations. The vaporization behavior of the real fuel has been improved testing blends of 7 hydrocarbons and a reduced multi-component model has been defined in order to reduce the computational cost of the CFD simulations. Particular care has been also dedicated to the modeling of the atomization and secondary breakup processes occurring to the GDI sprays. The multi-hole jets have been simulated by means of a new atomization approach combined with the Kelvin-Helmholtz/Rayleigh-Taylor hybrid model.

This paper aims to correlate the in-cylinder soot formation and the exhaust particle emissions for different methods of gasoline/ethanol fueling in spark ignition engine. In particular, the engine was fueled with gasoline and ethanol separately and not, in this latter case both blended (E30) and dual fueled (EDF). For E30 the bend was direct injected and for EDF, the ethanol was injected in the combustion chamber and the gasoline into the intake duct. For both the injection configurations, the same percentage of ethanol in gasoline was supplied: 30%v/v. The measurements were carried out at 2000 and 4000 rpm, under full load, and stoichiometric condition, in small single cylinder optical engine. 2D-digital imaging was performed to follow the combustion process with a high spatial and temporal resolution through a full-bore optical piston. The two-color pyrometry was applied for the analysis of the in cylinder soot formation in the combustion chamber.

Within the context of widening application of numerical simulations for shortening engine development times, the present work covers the issue of quasi-dimensional simulation of spark ignition engines. Multi-fuel operation was the main goal of the study, with the analysis of methane and its blends with hydrogen; gasoline was also considered as a reference case. Data recorded on two engines with practically the same geometry, was used for calibrating the model. The first power unit was of commercial derivation for small applications, while the second one featured optical accessibility through the piston crown. The relative difference between the two engines allowed the top-land region crevice to be identified as the major contributor to overall combustion evolution, especially during its late stages.

Non-intrusive measurements were carried out in an optical spark ignition GDI engine in order to characterize the chemical and physical processes involved using gasoline and bio-ethanol fuel. In particular, an optical 4 strokes small single cylinder engine for two wheel vehicles was used. It was equipped with an elongated piston with a wide sapphire window in the head and quartz cylinder. Exhaust emissions and engine performances were evaluated during the imaging and spectral measurements in order to investigate the spray characteristics and flame propagation with high spatial and temporal resolution. Several engine conditions based on homogeneous charge mixture conditions were investigated considering the effect of injection pressure and ethanol fuel too. The simultaneous use of the high injection pressure and bio-ethanol showed to be a valid answer to reduction of pollutants without worsening the performances.

Compression ignition engines are widely used for transport and energy generation due to their high efficiency and low fuel consumption. To minimize the environmental impact of this technology, the pollutant emissions levels at the exhaust are strictly regulated. To reduce the after-treatment needs, alternative strategies as the low temperature combustion (LTC) concepts are being investigated recently. The reactivity controlled compression ignition (RCCI) uses two fuels (direct- and port- injected) with different reactivity to control the in-cylinder mixture reactivity by adjusting the proportion of both fuels. In spite of the proportion of the port-injected fuel is typically higher than the direct-injected one, the characteristics of the latter play a main role on the combustion process. Use of gasoline for direct injection is attractive to retard the start of combustion and to improve the air-fuel mixing process.

The growing concerns over the pollutant emissions as well as the depletion of fossil fuel led to the research of advanced combustion mode and alternative fuels for the reduction both of fuel consumption and exhaust emissions. The dual-fuel injection system can be used to improve the engine performance and reduce the fossil fuel consumption performing simultaneously a direct-injection (DI) and a port-fuel-injection (PFI) of different fuels. Ethanol is one of the most promising alternative fuels for SI engines. It offers high anti-knock quality because of the high octane number; moreover, being an oxygenated fuel is very effective in particle emissions reduction. On the other hand, it is characterized by lower energy density mainly because of the low lower heating value (LHV). The aim of the paper is the investigation of the ethanol-gasoline dual fuel combustion on engine performance and emissions.