Search Results

Inerters have become a hot topic in recent years, especially in vehicle, train, and building suspension systems. The performance of a passive inerter and a semi-active inerter was analyzed and compared with each other and it showed that the semi-active inerter has much better performance than the passive inerter, especially with the Hybrid control method. Eight different layouts of suspensions were analyzed with a quarter car model in this paper. The adaptation of dimensionless parameters was considered for a semi-active suspension and the semi-active inerters. The performance of the semi-active inerter suspensions with different layouts was compared with a semi-active suspension with a conventional parallel spring-damper arrangement. It shows a semi-active suspension, with more simple configuration and lower cost, has similar or better compromise between ride and handling than a semi-active inerter with the Hybrid control.

The soft and rough terrain on the planet's surface significantly affects the ride and safety of rovers during high-speed driving, which imposes high requirements for the control of the suspension system of planet rovers. To ensure good ride comfort of the planet rover during operation in the low-gravity environment of the planet's surface, this study develops an active suspension control strategy for torsion spring and torsional damper suspension systems for planet rovers. Firstly, an equivalent dynamic model of the suspension system is derived. Based on fractal principles, a road model of planetary surface is established. Then, a fuzzy-PID based control strategy aimed at improving ride comfort for the planet rover suspension is established and validated on both flat and rough terrains.

The guiding mechanism of vehicle suspension can keep the wheels moving along planned trajectory. The geometrical design of the reasonable suspension guide mechanism can reduce the vibration transmitted to the body, improve trafficability and handling stability. The vehicle suspension design method was applied to the wheel-legged vehicle, enhancing ride performance. The optimization of suspension hard points can be obtained by using single variable method, adjusting each hard point coordinate independently. It is also widely recommended by using intelligent algorithm to solve well-designed multi-objective parameter optimization function. In this study, the multi-objective parameter optimization function was solved by using the NSGA-II (Non-dominated Sorted Genetic Algorithm-II). Computer simulations with half-car model were used to support the analysis in this study. ADAMS multibody dynamics software was also used to verify the reliability of the results.

The performance parameters of torsional vibration damper, including stiffness and damping, have great influence on the torsional vibration of automobile driveline. At present, the research on torsional vibration damper mainly concentrates on the torsional stiffness, but rarely on the torsional damping characteristics. This paper systematically studied the effect of torsional stiffness and damping on torsional vibration of automobile driveline under uniform speed conditions, accelerated and decelerated conditions, idling conditions and resonance conditions. The requirements on stiffness and damping of various operating conditions were summarized. The effect and requirements researched were useful to performance match design of torsional vibration damper.

Aiming at the difficulty of sovling the stiffness calculation of taper-leaf spring with variable stiffness, a combined method was proposed, which combine superposition method and finite difference method. Then the calculation results of different differential segments were compared with experimental results. The compared results show that the proposed method is effective and simple. So it has some practical significance in designing the taper-leaf spring. In addition, based on the stiffness test of the taper-leaf spring, the proper adjustments to the correction factor of the single parabolic leaf spring stiffness formula was recommended(ξ =0.92-0.96).

This paper presents the study of chassis tuning of a commercial vehicle, which has a rear suspension with dual stage leaf spring assembly and a front suspension with double wishbone torsion bar. To balance the handling and ride performance of the vehicle, it is necessary to tune the key suspension parameters of the chassis including the dual stage stiffness of the leaf spring, the contact load of the leaf spring, the torsional rigidity of the torsion bar, the force curve of the front and rear dampers etc. The chassis tuning process of a physical commercial vehicle was first put forward. In the proposed flowchart, the kinematics and statics of front & rear suspensions were checked at the beginning of the tuning. Then the tire mechanical characteristics were tested by using a plate-type tire tester and the inertial parameters of the vehicle were indirectly measured. The K&C characteristics of front and rear suspensions were also tested and compared with the benchmark vehicle's.

Vehicle needs suspension and steering systems with different features to fit different driving conditions. In normal straight driving condition, soft suspension and heavy steering systems are needed to achieve better ride comfort and straight line driving stability; in turning conditions, hard suspension and lightweight steering systems are needed to get better handing stability. The semi-active suspension system with Magneto-Rheological dampers can improve the ride comfort and handling performance of vehicle. Electrical power steering system is developed rapidly due to its portable and flexible operations as well as stable steering performance.

Semi-active suspension system (SASS) could enhance the ride comfort of the vehicle across different operating conditions through adjusting damping characteristics. However, current SASS are often calibrated based on engineering experience when selecting parameters for its controller, which complicates the achievement of optimal performance and leads to a decline in ride comfort for the vehicle being controlled. Linear quadratic constrained optimal control is a crucial tool for enhancing the performance of semi-active suspensions. It considers various performance objectives, such as ride comfort, handling stability, and driving safety. This study presents a control strategy for determining optimal damping force in SASS to enhance driving comfort. First, we analyze the working principle of the SASS and construct a seven-degree-of-freedom model.

Since steering wheel torque feedback is one of the crucial factors for drivers to gain road feel and ensure driving safety, it is especially important to simulate the steering torque feedback for a driving simulator. At present, steering wheel feedback torque is mainly simulated by an electric motor with gear transmission. The torque response is typically slow, which can result in drivers’ discomfort and poor driving maneuverability. This paper presents a novel torque feedback device with magnetorheological (MR) fluid and coil spring. A phase separation control method is also proposed to control its feedback torque, including spring and damping torques respectively. The spring torque is generated by coil spring, the angle of coil spring can be adjusted by controlling a brushless DC motor. The damping torque is generated by MR fluid, the damping coefficient of MR fluid can be adjusted by controlling the current of excitation coil.

To address the issue of PID control for automotive vibration, this paper supplements and develops the evaluation of automotive vibration characteristics, and proposes a vibration response quantity for evaluating the energy dissipation characteristics of automotive vibration. A two-degree-of-freedom single wheel model for automotive vibration control is established, and the conventional vibration response variables for ride comfort evaluation and the energy consumption vibration response variables for energy dissipation characteristics evaluation are determined. This paper uses the Adaptive Differential Evolution (ADE) algorithm to tune the PID control parameters and introduces an adaptive mutation factor to improve the algorithm's adaptability. Several commonly used adaptive mutation factors are summarized in this paper, and their effects on algorithm improvement are compared.

This study investigates the fundamental stiffness and damping properties of a self-damped pneumatic suspension system, based on both the experimental and analytical analyses. The pneumatic suspension system consists of a pneumatic cylinder and an accumulator that are connected by an orifice, where damping is realized by the gas flow resistance through the orifice. The nonlinear suspension system model is derived and also linearized for facilitating the properties characterization. An experimental setup is also developed for validating both the formulated nonlinear and linearized models. The comparisons between the measured data and simulation results demonstrate the validity of the models under the operating conditions considered. Two suspension property measures, namely equivalent stiffness coefficient and loss factor, are further formulated.

The tire is one of the key components that affect vehicle performance and ride quality. The rigid ring model has been widely used in the dynamic simulation of tire rolling uneven road surface, and calculate the tire stiffness and force of rim under quasi-static conditions. However, the traditional spring-damping between rim and belt is not accurate enough to describe the viscous damping force and hysteretic behavior of rubber. Therefore, it is necessary to propose a new rigid ring model, considering the viscoelasticity of tire side rubber and hysteretic behavior of rubber, to better adapt to the intermediate frequency response of tire. In this paper, the rigid ring model introduces the fractional derivative damping and friction force element to enhance the dynamic response of tire in higher frequency. Linear damping is replaced by a three-parameter fractional-order derivative damping model, and a Berg friction element was added between rim and belt.

Abrasion of the Electromechanical brake (EMB) brake pad during the braking process leads to an increase in brake gap, which adversely affects braking performance. Therefore, it is imperative to promptly detect brake pad abrasion and adjust the brake gap accordingly. However, the addition of extra gap adjustment or sensor detection devices will bring extra size and cost to the brake system. In this study, we propose an innovative EMB gap active adjustment strategy by employing modeling and analysis of the braking process. This strategy involves identifying the contact and separation points of the braking process based on the differential current signal. Theoretical analysis and simulation results demonstrate that this gap adjustment strategy can effectively regulate the brake gap, mitigate the adverse effects of brake disk abrasion, and notably reduce the response time of the braking force output. Monitoring is critical to accurately control EMB clamping force.

In order to improve the handling and stability of a light bus at high speed, a virtual model was established in Adams-Car and its anti-roll bar and bushing parameters were virtually optimized. The tyre mechanical characteristics were firstly tested by using a plate-type tyre tester and the Magic Formula parameters of the tyre were obtained. Then the virtual bus model's handling performance were studied by the simulation of central steering test and steady static circular test. An optimal matching method was put forward. By using genetic algorithm to conduct optimization, the optimised parameters were obtained. After that the anti-roll bar and bushing samples were respectively manufactured. At last, the comparative trials were performed in an automotive proving ground, and the subjective evaluation of the light bus's handling and stability was taken by three specialized assessors.

In this paper, a multi-mode active seat suspension with a single actuator is proposed and built. A one-DOF seat suspension system is modelled based on a quarter car model of commercial vehicle with an actuator which is comprised of a DC motor and a gear reducer. Aiming at improving ride comfort and reducing energy consumption, a multi-mode controller is established. According to the seat vertical acceleration and suspension dynamic travel signals, control strategies switch between three modes: active drive mode, energy harvesting mode and plug breaking mode.

Suspension kinematics and compliance strongly influence the handling performance of the vehicle. The kinematics and compliance characteristics are determined by the suspension geometry and stiffness of suspension bodies and elastic components. However, it is usually inefficient to model all the joints, bushings, and linkage deformation in a full vehicle model. By transforming the complex modeling problem into a data-driven problem tends to be a good solution. In this research, the neural-network-based suspension kinematics and compliance model is built and implemented into a 17 DOF full vehicle model, which is a hybrid model with state variables expressed in the global coordinate system and vehicle coordinate system. The original kinematics and compliance characteristics are derived from multibody dynamics simulation of the suspension system level.

This paper presented one calculation method of the contact load, which is the load acted on the spring at the moment when the second-level stiffness of the spring just begins to work. In the proposed method, the contact load calculation mainly based on the dynamic load of the unsprung mass and the road grades and the commonly driving speed were also considered. A semiempirical formula of the contact load was put forward. Then the contact load of the commercial bus's rear suspension was respectively calculated by using the proposed formula and traditional methods(geometric mean method and average load method) to compare each other and to verify the new method. Later, the spring samples were respectively manufactured based on the calculation results. At last, the validation tests were respectively performed in an automotive proving ground.

Elastomeric bushings are widely used in the passenger cars to make the cars have an ideal vehicle Noise, Vibration and Harshness (NVH) performance. However, elastomeric bushings also influence on the vehicle handling, ride and the durability performance of each component in the vehicle suspension system. It is relatively easy and cost effective to change the compliance of the bushing components compared with other method because they are made of elastomeric materials. The design of an elastomeric bushing is really a big challenge. One of the main difficulties comes from the different target compliance is wanted according to the handling, ride and durability demand at each different orientation (indicated by X Y Z) of the bushing. In this paper the following procedure was used for optimization of suspension elastomeric bushing compliance. Firstly, a detailed multi-body model was built including the nonlinear bushing effects and lower control arm flexibility.

This study presents a hybrid optimization approach of TOPSIS-based Taguchi method and entropy measurement for the determination of the optimal suspension parameters to achieve an enhanced compromise among ride comfort, road friendliness which means the extent of damage exerted on the road by the vehicles, and handling stabilities of a self-dumping truck. Firstly, the full multi-body dynamic vehicle model is developed using software ADAMS/Car and the vehicle model is then validated through ride comfort road tests. The performance criterion for ride comfort evaluation is identified as root mean square (RMS) value of frequency weighted acceleration of cab floor, while the road damage coefficient is used for the evaluation of the road-friendliness of a whole vehicle. The lateral acceleration and roll angle of cab were defined as evaluation indices for handling stability performance.

A detailed multi-body dynamic model of a passenger car was modeled using ADAMS/Car and then checked by the ride comfort and handling stability test results in this paper. The performance criterion for ride comfort evaluation was defined as the overall weighted acceleration root mean square (RMS) value of car body floor, while the roll angle and lateral acceleration of car body were considered as evaluation indicators for handling stability performance. Simultaneously, spring stiffness and shock absorber damping coefficients of the front and rear suspensions were taken as the design variables (also called factors), which were considered at three levels. On this basis, a L9 orthogonal array was employed to perform the ride and handling simulations.