Search Results

Individual hydrocarbon conversion efficiencies of engine-out emissions have been measured for four different catalyst formulations (Pd-only, trimetallic, Pd/Rh, and Pt/Rh) during stoichiometric and rich operation. The measurements were carried out as a function of fuel-air equivalence ratio (Φ) using a dynamometer-controlled 1993 Ford V8 engine and capillary gas chromatography. HC conversion efficiency was examined in terms of mass conversion efficiency and also using three new definitions of catalyst conversion efficiency. The efficiencies across the four catalysts show similar trends with Φ for almost all HC species. The catalyst efficiencies for alkanes, alkenes, and aromatic species decrease as Φ increases above stoichiometric: alkane efficiencies decrease faster than alkenes which in turn decrease faster than aromatics. All efficiencies fall to zero near Φ = 1.08 except those of MTBE and acetylene, which remain near 100%.

In a gasoline engine, the unswept in-cylinder residual gas and introduction of external EGR is one of the important means of controlling engine raw NOx emissions and improving part load fuel economy via reduction of pumping losses. Since the trapped in-cylinder Residual Gas Fraction (RGF, comprised of both internal, and external) significantly affects the combustion process, on-line diagnosis and monitoring of in-cylinder RGF is very important to the understanding of the in-cylinder dilution condition. This is critical during the combustion system development testing and calibration processes. However, on-line measurement of in-cylinder RGF is difficult and requires an expensive exhaust gas analyzer, making it impractical for every application. Other existing methods, based on measured intake and exhaust pressures (steady state or dynamic traces) to calculate gas mass flowrate across the cylinder ports, provide a fast and economical solution to this problem.

This paper reports on DaimlerChrysler's participation in the Ad Hoc Diesel Fuels Test Program. This program was initiated by the U.S. Department of Energy and included major U.S. auto makers, major U.S. oil companies, and the Department of Energy. The purpose of this program was to identify diesel fuels and fuel properties that could facilitate the successful use of compression ignition engines in passenger cars and light-duty trucks in the United States at Tier 2 and LEV II tailpipe emissions standards. This portion of the program focused on minimizing engine-out particulates and NOx by using selected fuels, (not a matrix of fuel properties,) in steady state dynamometer tests on a modern, direct injection, common rail diesel engine.

Electrically assisted turbochargers are a promising technology for improving boost response of turbocharged engines. These systems include a turbocharger shaft mounted electric motor/generator. In the assist mode, electrical energy is applied to the turbocharger shaft via the motor function, while in the regenerative mode energy can be extracted from the shaft via the generator function, hence these systems are also referred to as regenerative electrically assisted turbochargers (REAT). REAT allows simultaneous improvement of boost response and fuel economy of boosted engines. This is achieved by optimally scheduling the electrical assist and regeneration actions. REAT also allows the exhaust turbine to operate within a narrow range of optimal vane positions relative to the unassisted variable geometry turbocharger (VGT). The ability to operate within a narrow range of VGT vane positions allows an opportunity for a more optimal turbine design for a REAT system.

Charge motion is known to accelerate and stabilize combustion through its influence on turbulence intensity and flame propagation. The present work investigates the effect of charge motion generated by intake runner blockages on combustion characteristics and emissions under part-load conditions in SI engines. Firing experiments have been conducted on a DaimlerChrysler (DC) 2.4L 4-valve I4 engine, with spark range extending around the Maximum Brake Torque (MBT) timing. Three blockages with 20% open area are compared to the fully open baseline case under two operating conditions: 2.41 bar brake mean effective pressure (bmep) at 1600 rpm, and 0.78 bar bmep at 1200 rpm. The blocked areas are shaped to create different levels of swirl, tumble, and cross-tumble. Crank-angle resolved pressures have been acquired, including cylinders 1 and 4, intake runners 1 and 4 upstream and downstream of the blockage, and exhaust runners 1 and 4.

Diesel vehicles have significant advantages over their gasoline counterparts including a more efficient engine, higher fuel economy, and lower emissions of HC, CO, and CO2. However, NOx control is more difficult on a diesel because of the high O2 concentration in the exhaust, making conventional three-way catalysts ineffective. The most promising technology for continuous NOx reduction onboard diesel vehicles is Selective Catalytic Reduction (SCR) using aqueous urea. Recent work with urea SCR has involved aftertreatment for the 1.2L DIATA common-rail diesel engine. This engine was used in Ford's hybrid-electric vehicle, the Prodigy, which was developed under the PNGV (Partnership for a New Generation of Vehicles) program. An emission control system consisting of a diesel particulate filter followed by an underbody SCR system was used successfully to meet ULEV emission standards (0.2 g/mi NOx, 0.04 g/mi particulate matter (PM)).

In order to assess the amount of airborne particulate matter (PM) attributable to vehicle disk brakes, a system was devised for collecting brake wear debris on a laboratory brake dynamometer. The brake dynamometer test hardware was enclosed and vented through a duct in which the airflow was controlled to ensure isokinetic sampling. Two brake dynamometer simulations were implemented: urban driving (low velocity, low g) and the Auto Motor und Sport (AMS, high velocity, high g). These test procedures were performed repeatedly on the brake system hardware of vehicles utilizing three different friction material types: low-metallic, semi-metallic, and non-asbestos organic (NAO). Airborne brake wear was collected on filters and via other airborne PM sampling techniques. Larger, non-airborne wear debris was collected from the wheel, below the brake, and brushed off the hardware. Considering the effect of the wheel, 50-70% of the collected wear debris was airborne PM.

Cam-phasing is increasingly considered as a feasible Variable Valve Timing (VVT) technology for production engines. Additional independent control variables in a dual-independent VVT engine increase the complexity of the system, and achieving its full benefit depends critically on devising an optimum control strategy. A traditional approach relying on hardware experiments to generate set-point maps for all independent control variables leads to an exponential increase in the number of required tests and prohibitive cost. Instead, this work formulates the task of defining actuator set-points as an optimization problem. In our previous study, an optimization framework was developed and demonstrated with the objective of maximizing torque at full load. This study extends the technique and uses the optimization framework to minimize fuel consumption of a VVT engine at part load.

The direct injection gasoline spray-wall interaction was characterized inside a heated pressurized chamber using various visualization techniques, including high-speed laser-sheet macroscopic and microscopic movies up to 25,000 frames per second, shadowgraph, and doublespark particle image velocimetry. Two hollow cone high-pressure swirl injectors having different cone angles were used to inject gasoline onto a heated plate at two different impingement angles. Based on the visualization results, the overall transient spray impingement structure, fuel film formation, and preliminary droplet size and velocity were analyzed. The results show that upward spray vortex inside the spray is more obvious at elevated temperature condition, particularly for the wide-cone-angle injector, due to the vaporization of small droplets and decreased air density. Film build-up on the surface is clearly observed at both ambient and elevated temperature, especially for narrow cone spray.

Projected NOx and fuel costs are compared for a plasma-catalyst system and an active lean NOx catalyst system. Comparisons are based on modeling of FTP cycle performance. The model uses steady state laboratory device characteristics, combined with measured vehicle exhaust data to predict NOx conversion efficiency and fuel economy penalties. The plasma system uses a proprietary catalyst downstream of a plasma discharge. The active lean NOx catalyst uses a catalyst along with addition of hydrocarbons to the exhaust. For the plasma catalyst system, NOx conversion is available over a wide temperature range. Increased electrical power improves conversion but degrades vehicle fuel economy; 10 J/L energy deposition costs roughly 3% fuel economy. Improved efficiency is also available with larger catalyst size or increased exhaust hydrocarbon content. For the active lean NOx system, NOx conversion is available only in a narrow temperature range.

The U.S. Environmental Protection Agency, U.S. Department of Transportation's National Highway and Traffic Safety Administration, and the California Air Resources Board have recently released proposed new regulations for greenhouse gas emissions and fuel economy for light-duty vehicles and trucks in model years 2017-2025. These proposed regulations intend to significantly reduce greenhouse gas emissions and increase fleet fuel economy from current levels. At the fleet level, these rules the proposed regulations represent a 50% reduction in greenhouse gas emissions by new vehicles in 2025 compared to current fleet levels. At the same time, global growth, especially in developing economies, should continue to drive demand for crude oil and may lead to further fuel price increases. Both of these trends will therefore require light duty vehicles (LDV) to significantly improve their greenhouse gas emissions over the next 5-15 years to meet regulatory requirements and customer demand.

Previously reported experiments revealed the presence of a small number of clusters or very small particles in the effluent of a nonthermal plasma reactor when treating a simulated engine exhaust mixture. These clusters are smaller than 7 nm. The quantity of clusters is orders of magnitude smaller than the particulate diesel or gasoline engine exhaust typically contains. In this report, we describe further experiments designed to determine the chemical composition of the clusters. Clusters were collected on the surface of a silicon substrate by exposing it to the effluent flow for extended time periods. The resulting deposits were analyzed by high mass resolution SIMS and by XPS. The SIMS analysis reveals NH4+, CH6N+, SO-, SO2-, SO3- and HSO4- ions. XPS reveals the presence of N and S at binding energies consistent with that of ammonium sulfate.

The Fischer-Tropsch (FT) process can be used to synthesize diesel fuels from a variety of energy sources, including coal, natural gas and biomass. Diesel fuels produced from the FT process are essentially sulfur-free, have very low aromatic content, and have excellent ignition characteristics. Because of these favorable attributes, FT diesel fuels may offer environmental benefits over transportation fuels derived from crude oil. Previous tests have shown that FT diesel fuel can be used in unmodified engines and have been shown to lower regulated emissions. Whereas exhaust emissions reductions from these previous studies have been impressive, this paper demonstrates that far greater exhaust emissions reductions are possible if the diesel engine is optimized to exploit the properties of the FT fuels. A Power Stroke 7.3 liter turbocharged diesel engine has been modified for use with FT diesel.

In 1999, the first generation NOx sensor from NGK Spark Plug, Co., Ltd. was commercialized for use in gasoline LNT NOx after-treatment systems [ 1 ]. Since then, as emissions regulations and OBD requirements have become more stringent, the demand for a high-accuracy NOx sensor with fast light-off has increased, particularly for diesel after-treatment systems. To meet such market demands, NGK Spark Plug, Co., Ltd. has developed, in collaboration with Ford Motor Company, a second generation NOx sensor.

Current engine development processes typically involve extensive steady-state and simple transient testing in order to characterize the engine's fuel consumption, emissions, and performance based on several controllable inputs such as throttle, spark advance, and EGR. Steady-state and simple transient testing using idealistic load conditions alone, however, is no longer sufficient to meet powertrain development schedule requirements. Mapping and calibration of an engine under transient operation has become critically important. And, independent engine development utilizing accelerated techniques is becoming more attractive. In order to thoroughly calibrate new engines in accelerated fashion and under realistic transient conditions, more advanced testing is necessary.

The Automotive Industry/Government Emissions Research CRADA (AIGER) has been working to develop a new methodology for the direct determination of nonmethane hydrocarbons (DNMHC) in vehicle testing. This new measurement technique avoids the need for subtraction of a separately determined methane value from the total hydrocarbon measurement as is presently required by the Code of Federal Regulations. This paper will cover the historical aspects of the development program, which was initiated in 1993 and concluded in 2002. A fast, gas chromatographic (GC) column technology was selected and developed for the measurement of the nonmethane hydrocarbons directly, without any interference or correction being caused by the co-presence of sample methane. This new methodology chromatographically separates the methane from the nonmethane hydrocarbons, and then measures both the methane and the backflushed, total nonmethane hydrocarbons using standard flame ionization detection (FID).

A diesel fuel and air diffusion flame burner system has been designed for laboratory simulation of diesel exhaust gas. The system consists of mass flow controllers and a fuel pump, and employs several unique design and construction features. It produces particulate emissions with size, number distribution, and morphology similar to diesel exhaust. At the same time, it generates NOx emissions and HC similar to diesel. The system has been applied to test plasma discharges. Different design discharge devices have been tested, with results indicating the importance of testing devices with soot and moisture. Both packed bed reactor and flat plate dielectric barrier discharge systems remove some soot from the gas, but the designs tested are susceptible to soot fouling and related electrical failures. The burner is simple and stable, and is suitable for development and aging of plasma and catalysts systems in the laboratory environment.

The Ethanol-Boosted Direct Injection (EBDI) demonstrator engine is a collaborative project led by Ricardo targeted at reducing the fuel consumption of a spark-ignited engine. This paper describes the design challenges to upgrade an existing engine architecture and the synergistic use of a combination of technologies that allows a significant reduction in fuel consumption and CO₂ emissions. Features include an extremely reduced displacement for the target vehicle, 180 bar cylinder pressure capability, cooled exhaust gas recirculation, advanced boosting concepts and direct injection. Precise harmonization of these individual technologies and control algorithms provide optimized operation on gasoline of varying octane and ethanol content.

The requirement of reducing HC emissions during cold start and improving transient performance has prompted a study of the fuel injection process. Port-fuel-injection with the Intake-valve open using small droplets is a potentially feasible option to achieve the goals. To gain a better understanding of the injection process, the effects of droplet size, injection timing, and coolant temperature on the total and speciated HC emissions were tested In a Single-cylinder engine. It was found that droplet size plays an important role in the total HC emission increase during open-valve injection, especially with cold operation. Large droplets (300 μm SMD) produced a substantial HC increase while small droplets (14 μm SMD) produced no observable increase. Increase In the total HC emissions was always accompanied by an increase in the heavy fuel components in the exhaust gases.

With the adoption of the California Low-Emission Vehicle Regulations and the associated lower emission standards such as LEV (Low-Emission Vehicle in 1990), ULEV (Ultra-Low-Emission Vehicle), and LEV II (1998 with SULEV-Super Ultra Low Emission Vehicle), concerns were raised by emissions researchers over the accuracy and reliability of collecting and analyzing emissions measurements at such low levels. The primary concerns were water condensation, optimizing dilution ratios, and elimination of background contamination. These concerns prompted a multi-year research program looking at several new sampling techniques. This paper will describe the cooperative research conducted into one of these new technologies, namely the Bag Mini-Diluter (BMD) and Direct Vehicle Exhaust (DVE) Volume system.