Search Results

During the last ten years, there is a significant tendency in automotive design to use lower aspect ratio tires and meanwhile also more and more run-flat tires. In appropriate publications, the influences of these tire types on the dynamic loads - transferred from the road passing wheel center into the car - have been investigated pretty well, including comparative wheel force transducer measurements as well as simulation results. It could be shown that the fatigue input into the vehicle tends to increase when using low aspect ratio tires and particularly when using run-flat tires. But which influences do we get for the loading and fatigue behavior of the respective rims? While the influences on the vehicle are relatively easy to detect by using wheel force transducers, the local forces acting on the rim flange (when for example passing a high obstacle) are much more difficult to detect (in measurement as well as in simulation).

The firewall design of a BMW1 is optimized for interior noise and weight using a Hybrid Interior Noise Synthesis (HINS) approach. This method associates a virtual firewall with a test based body model. A vibro-acoustic model of the firewall panel, including trim elements and full vehicle boundary conditions, is used for predictions in the 40 Hz - 400 Hz range. The short calculation time of this set-up allows multiple design iterations. The firewall noise is reduced by 0.9 dB and its mass by 5.1% through structural changes. Crashworthiness is maintained at its initial level using advanced steel processing. The total interior noise shows improvement in the 90 Hz - 140 Hz range.

The rate in the electrification of vehicles has risen in recent years. With intensified development more and more attention is paid to the noise and vibration in such vehicles especially from the EDU (Electric Drive Unit). In this paper the main NVH simulation process of a high-speed E-axle up to 30,000 rpm for premium class vehicle application is presented. The high speed, high-power density and lightweight design introduces new challenges. Benchmarking of different EDUs and vehicles leads to targets which can be used at the early stage of development as subsystem targets. This paper shows the CAE methodology which can be used to verify the design and guarantee the target achievement. Using CAE both source and structure can be optimized to improve the NVH behavior.

Stringent legislation by governmental agencies concerning human exposure to noise and vibrations on the one hand and the growing consumer awareness and need for comforts on the other hand are forcing automotive manufacturers to improve their products. Computer Aided Engineering (CAE) techniques and software tools enable virtual optimization thereby eliminating the need to build and test expensive prototypes. Deterministic, element-based approaches as the Finite Element (FE) and/or Boundary Element (BE) methods have become the tools of choice for analyzing the steady-state and dynamic characteristics of vehicles. However, these two techniques are limited to low-frequency applications due to the need for high mesh densities at mid and high frequencies resulting in higher computational costs and higher numerical errors associated with the polynomial approximations of the acoustic field variables. This paper discusses two types of approaches, viz.

The rate in the electrification of vehicles has risen in recent years and, despite that electric vehicles are quiet, NVH remains a major requirement of vehicle development. The typical NVH issues are gear whine from the gearbox, noise from the E-machine or electromagnetic whine, as well as the noise from the inverter, and noise from inverter harmonics effect on E-machine. Simulation methodologies and CAE workflows are being enhanced to contribute to electric drive systems development. Front loading in the concept and layout design phase are necessary to avoid significant NVH issues at the end of development. The authors previously presented a workflow for combining the electric and mechanical noise for electric drives for the concept and layout design phases. This paper shows an application of the formerly presented workflow for NVH simulation and validation of a system with an Interior Permanent Magnet (IPM) E-machine.

This paper presents a CAE based approach to accurately simulate and optimize Ride and Handling metrics. Because of the wide range of vehicle phenomena involved, across the variety of frequency ranges, it is essential that the vehicle model includes proper representation of the dynamic properties of the various subsystems (e.g. tires, steering, PT, etc.) Precise correlation between test and simulation for standalone vehicle components and systems is achieved by replicating in the MBS (Multi-body Simulation) the same tests and boundary conditions. This allows the analyst to correctly define those crucial elements and parameters which have the greatest effect on the R&H attribute to be investigated. Setting up the simulation to correctly represent only one single maneuver simulation at a time would not allow the analyst to consider how the dynamic properties of the chassis design variables should be tuned to achieve to best balance and trade-offs.

The objective of this paper is to present the development and the use of a numerical model to predict noise radiated from manual gearboxes due to gear rattle using Computer-Aided Engineering (CAE) technologies. This CAE process, as outlined in this paper, includes measured data, computational flexible multibody dynamics, and vibro-acoustic analysis. The measured data is used to identify and reproduce the input excitation which is primarily generated from engine combustion forces. The dynamic interaction of the gearbox components, including flywheel, input/output shafts, contacting gear-pairs, bearings, and flexible housing is modeled using flexible multibody techniques. The acoustic response to the vibration of the gearbox housing is then predicted using vibro-acoustic techniques. These different technologies are augmented together to produce a virtual gearbox that can be used in noise, vibration, and harshness (NVH) performance evaluations.

Prediction of the drive-by noise level in the early design stage of an automotive vehicle is feasible if the source signatures and source-receiver transfer functions may be determined from simulations based on the available CAD/CAE models. This paper reports on the performance of a drive-by noise synthesis procedure in which the transfer functions are numerically evaluated by employing the Fast Multipole Boundary Element Method (FMBEM). The proposed synthesis procedure first computes the steady-state receiver contributions of the sources as appearing from a number of vehicle positions along the drive path. In a second step, these contributions are then combined into a single transient signal from a moving vehicle for each source-receiver pair by means of a travel time correction.

While CAE methods allow improving nominal product design using virtual prototypes, uncertainty and variability in properties and manufacturing processes lead to scatter in actual performances. Uncertainty must hence be incorporated in the CAE process to guarantee the robustness and reliability of the design. This paper presents an overview of uncertainty-based design in automotive and aerospace engineering. Fuzzy methods take uncertainty into account, whereas reliability analysis and a reliability-based design optimization framework can deal with variability. Key enabling technologies to alleviate the computational burden, such as workflow automation, substructuring and design of experiments, are discussed, and industrial applications are presented.