Search Results

This paper deals with an analytical method to calculate the press-fit tolerance and fits between gears and shaft for automotive applications. The relative interferences increase sharply in the small diameter range, therefore one must be especially careful when designing small diameter joints. The strength of press-fit depends on the amount of relative interference; extreme interference leads to excessive contact stresses between the gear and shaft eventually leading to failure. Too little interference leads to slippage of gear on the shaft. In the press fit connection a shaft's spline rolling operation and gear internal broaching is eliminated. It is more economical than a conventional spline connection. Press fit connections are used in various transmission between a shaft and a gear. They are used in 6 speed transmission to 9-speed transmission for (German based Vehicle Manufacturer) heavy and light commercial vehicle company.

Vibrational fatigue is a metal fatigue caused by the forced vibrations which are purely random in nature. The phenomenon is predominantly important for the components/systems which are subjected to extreme vibration during its operation. In a vehicle, an engine is the main source of vibration. The vibrational fatigue, therefore, plays a key role in the deterioration of engine mounted components. Multiple test standards and methodologies are available for validating engine mounted parts of an automobile. These might not be appropriate in the case of an off- road vehicle as the vibrational exposure of engine mounted components of an off-road vehicle is entirely different. In the case of an off-road vehicle, the engine mounted components are subjected to a comparatively higher level of vibration for a longer duration of time as compared to the passenger cars.

This paper presents the analysis and experimental validation of c-spring and its stiffness properties in the gear shift synchronizer system. A synchronizer assembly for a transmission comprises of a synchronizer hub carried by a torque delivery shaft and a cone clutch member carried by a gear and a synchronizer blocking ring. The gear shift sleeve is meshing over the teeth of the clutch hub. The c-spring is positioned in the inner circumference of the rim position of the clutch hub and strut keys will be positioned at the slots on the clutch hub, which are usually 120 degree apart. As the sleeve moves while gear shifting, it pushes down the strut keys which compress the C-spring radially inward; this gives the strut load. The strut keys, which are pushed down by the sleeve, will apply force on the c-spring from radial directions. Since the c-spring is in the shape of an arc it is assumed as a curved beam for the analysis.

India's high Air Pollution level is the focus of discussions as we grow. Plans to combat this menace and implement the latest Technologies are gathering pace. The increasingly stringent emission legislations provide a continuous challenge for the non-road market. Tractor manufacturers are evaluating the need for cost-effective technology to meet upcoming stringent emissions targets. Simply following global approach may not work for Indian market considering the customer usage pattern & perceptions. With an anticipation of upcoming emission norms being based on US-EPA TIER-4 final up to 75 Hp, major technology up gradation is expected for farm equipment sold in India. The enormous diversification of engines within the different power classes as well as the operation specific requirements regarding various duty cycles, robustness and durability, requires specific solutions to meet these legal limits.

In driving, Steering is the input motion to the vehicle. The driver uses steering input to change the direction of the vehicle. During Parking or U turn bends the Steering is locked and later released to follow the desired path. Steering return ability is defined as the ratio of difference between steering wheel position at lock condition and steering wheel angle after 3 seconds of release to the steering wheel angle at lock condition. Having proper steering return ability characteristics has an important effect on vehicle steering characteristics. In this study, a full vehicle ADAMS model is prepared, and virtual steering return ability have been simulated in ADAMS/CAR for a Pickup truck vehicle. Simulated responses in the steering wheel angle have been validated by comparison with measurements. A Design of Experiment study is setup and Iterations are carried out to find the effect of Hard points and friction parameters.

In farm tractors, the available drawbar power, and Power Take-Off (PTO) power are generally lower than the engine power due to parasitic losses. These losses are caused by engine-driven auxiliary loads such as cooling fans, hydraulic pumps for power steering, alternators, etc. Minimizing these parasitic losses can increase the available drawbar power and PTO power, resulting in direct fuel savings by reducing fuel consumption. The continuous increase in fuel costs and the environmental impact of emitted gases from burned fuel into the atmosphere have necessitated the replacement of hydraulic power steering and mechanical fans with Electric Power Steering (EPS) and electric fans, respectively, to improve efficiency. The existing battery has been replaced with a higher capacity battery to provide power to the electric fan, electric power steering, and other electrical components.

This paper discusses the development of an all speed governed diesel-natural gas dual fuel engine for agricultural farm tractor. A 45 hp, 2.9 liters diesel-natural gas dual fuel engine with a novel closed loop secondary fuel injection system was developed. A frugal approach without any modification of the base mechanical diesel fuel injection system was followed. This approach helped to minimize the cost impact, while meeting performance and emissions at par with neat diesel operation. Additional cost on gas injection system is redeemed by cost savings on diesel fuel. The dual fuel technology developed by Mahindra & Mahindra Ltd., substitutes on an average approximately 40% of diesel with compressed natural gas, meeting the TREM III A emission norms for dual fuel while meeting all application requirements. The governing performance of the tractor was found to be superior than base diesel tractor.

Leaf Springs are commonly used as a suspension in heavy commercial vehicles for higher load carrying capacity. The leaf springs connect the vehicle body with road profile through the axle & tire assembly. It provides the relative motion between the vehicle body and road profile to improve the ride & handling performance. The leaf springs are designed to provide linear stiffness and uniform strength characteristics throughout its travel. Leaf springs are generally subjected to dynamic loads which are induced due to different road profiles & driving patterns. Leaf spring design should be robust as any failure in leaf springs will put vehicle safety at risk and cost the vehicle manufacturer their reputation. The design of a leaf spring based on conventional methods predicts the higher stress levels at the leaf spring center clamp location and stress levels gradually reduce from the center to free ends of the leaf spring.

A tractor is vehicle specifically designed to deliver a high tractive effort at slow speeds for carrying out various agriculture operations like ploughing, rotavation etc. using implement. Hydraulic system is a key feature which connects these implements with the tractor. It controls the position and draft of the implement depending upon the type of crop, farming stage, implement type and soil conditions. These variations induces extreme range of load on the hydraulic system, thus making it challenging to design these components. Bell crank assembly is one of the main components of hydraulic system which controls the draft (thus, the loads experienced by tractor) through load sensing mechanism. Often bell crank assembly failures are reported from field due to uneven soil hardness and presence of rocks. This paper studies one of such bell crank assembly failures in the field. The failure was reported after half life cycle of usage during agriculture Operation.

The Tractors are inevitable in the world due to its remarkable contribution majorly in farming process and other applications. the farming equipment needs to perform multiple applications to enhance the productivity and increased horsepower demands all-wheel drive (Refer fig. 1) or four-wheel drive option in the tractor. So, it is becoming a mandatory feature. The main objective of this study is, improving the torsional fatigue life in front axle spindle shaft by modifying the spline design and optimizing induction hardening heat treatment process in such a way that the other part of the system will have a minor or no design change. It helps us to reduce the part count variability, lower manufacturing cost and development time.

For meeting upcoming BS IV & BS V emission norms in Heavy Commercial Vehicles, most of the manufacturers are taking SCR after treatment route. Though SCR system is more complex and involves higher cost impact, an optimized SCR system can bring down the payback period to about one year due to improved fuel economy. For development of an SCR after treatment system, selection of a correct SCR catalyst and its position in the system is very important. NOX conversion efficiency of catalyst depends on exhaust gas temperature at the catalyst and the velocity distribution over the face of the catalyst. Generally catalysts are evaluated for the conversion efficiency in engine test bed. In a drive to have a first-time-right solution, a CFD analysis was carried out considering the low and high flow rate conditions. CFD simulation models and the corresponding results were used as a predictive tool in the exhaust system development process.

As the FTP-75 drive cycle does not have a prescribed gear shift pattern, automotive OEMs have the flexibility to design. Conventionally, gear shift pattern was formulated based on trial and error method, typically with 10 to 12 iterations on chassis dynamometer. It was a time consuming (i.e. ~ 3 to 4 months) and expensive process. This approach led to declaring poor fuel economy (FE). A simulation procedure was required to generate a gear shift pattern that gives optimal trade-off amongst conflicting objectives (FE, performance and emissions). As a result, a simulation tool was developed in MATLAB to generate an optimum gear shift pattern. Three different SUV/UV models were used as test vehicles in this study. Chassis dyno testing was conducted, and data was collected using the base and optimized gear shift patterns. Dyno test results with optimized gear shift pattern showed FE improvement of ~ 4 to 5% while retaining the NOx margin well above engineering targets.

In sheet metal painting for various applications like tractor and automobiles, most attractive coating is metallic paints. It is widely applied using 3 coat 2 bake or 3 coat 1 bake technology. Both options, results in high energy consumption, higher production through put time and lower productivity in manufacturing process. During various brainstorming and sustainability initiatives, paint application process was identified to reduce burden on environment and save energy. Various other industry benchmarking and field performance requirement studies helped to identify critical quality parameters. There was collaboration with supplier to develop monocoat system without compromising any performance and aesthetic properties. This resulted in achieving better productivity, elimination of two paint layers, substantial reduction in volatile organic content, elimination of one baking cycle and energy saving.

Tractors in the field are exposed to adverse operating conditions and are surrounded by dust and dirt. The tiny, thin and sharp broken straw and husks surround the system in reaper operation. The tractors which are equipped with air conditioning system tend to show detrimental effects in cooling performance. The compressor trips frequently by excess pressure developed in the system due to condenser clogging and hence cooling performance is reduced considerably. The air conditioning performance reduces due to the clogged condenser located on the top roof compartment of operator’s cabin, which is better design than keeping in front of radiator where clogging happens every hour and customer need to stop the tractor to clean it with specific blower.

Being a safety critical aggregate, every aspect of brake system is considered significant in vehicles operations. Along with optimum performance of brake system in terms of deceleration generation, brake pedal feel or brake feel is considered as one of the key elements while evaluating brake system of vehicles. There are many factors such as liner and drum condition, road surface, friction between linkages which impress the pedal feel. Out of these, in this paper we will be discussing the factors which influence the brake pedal feel in relation to the driver comfort and confidence building. Under optimum braking condition, brake operation must be completed with pedal effort not very less or not very high, brake pedal feel must be firm throughout the operation, in such a way that it will not create fatigue and at the same time it will give enough confidence to the driver while operating with acceptable travel.

The braking systems for modern day commercial vehicles with GVWs ranging above 7.5 metric tons use the typical s-cam drum brake system, where pressurized air is the actuating medium. The s-cam drum brake systems are popular today even after the advent and penetration of air disc brake systems, the main reasons being, cost-effectiveness, robustness, satisfactory performance and good component life. However, the brake systems of commercial vehicles (both M and N category) are frequently grappled with NVH issues particularly in the form of brake squeal noise (low frequency and high frequency). The noise with frequency more than 500 Hz can be generally defined as brake squeal. There has been a lot of work done and is being continued, at theoretical level, analytical level and experimental level to tackle with this issue.

One of the major discomforts while driving any medium to heavy commercial vehicle is brake judder. Brake judder can be defined as vibrations felt on steering wheel or brake pedal or cabin floor, when brakes are applied at certain speeds and pressures. The frequencies of this judder lie as high as 100 Hz to as low as 20 Hz. The brake judder is caused by a number of factors, which makes providing a universal solution difficult. Some of the causes are related to part fitment, part quality, material selection, manufacturing process, Design consideration, environmental factors, etc. This paper gives us a brief idea about resolution of judder problem in intermediate commercial vehicle by series of trials and this methodology can be applied in heavy commercial vehicles also. This paper gives reader an insight about step by step root cause analysis of brake judder on actual vehicle and an approach in resolving the judder problem.

In an off-road vehicle, Vehicle Structure plays a major role in passenger safety, Aesthetics, Durability, through a validated construction of canopy structure. This structure is to maintain the shape of the vehicle and to support various loads acting on the vehicle. In present market a safe, Durable, Robust, Waterproof, Noise less, Light weight and cost-effective off-road vehicle will always be a delight for any customer. However, the current conventional way of Soft top vehicle structure use metal brackets and formed sheet parts to create a structure to retain the canopy shape in place. These conventional structures are often heavier and would have many demerits such as heavy weight, Corrosion, Risk of canopy tear due to metallic structure edges and inappropriate draining, water management. Considering this we replaced the heavy metal brackets in to blow molded plastic parts.

S-cam air brake system is provided in almost all commercial vehicles having tonnage above 7.5-ton. In S-Cam brake system, drum to brake lining gap (henceforth referred to as ‘brake lining gap’ or simply ‘gap’ for convenience) range is an important factor which can impact braking behavior during brake application. Different OEMs (Original Equipment Manufacturers) define different brake lining gap ranges between S-cam brake lining and drum. This range depends majorly on the internal mechanism deployed in ASA (Auto Slack Adjuster). When these brake lining gaps start lowering i.e. when they fall in the range of 0 to 0.4 mm, or they become unstable (checked by feeler gauge at inspection window provided on dust cover of S-cam) then it starts impacting brake behavior in the subject vehicles.

This paper deals with new trends in materials & heat treatment in automotive transmission shafting. The material is S48C a low carbon alloy steel and material for automotive shaft special significance as it reduces overall cost in vehicle transmission shafts. Conventional method of shaft heat heat-treatment is case hardening for 20MnCr5. S48C is low-carbon alloy steel. This is an alternate proposal to 20MnCr5.There are lot of advantages in induction hardening over case hardening. Also induction hardening process with S48C material becomes cheaper than case-hardening with 20MnCr5.Strength and resistance to stress must therefore be carefully considered during the material selection and heat-treatment process. We have done Static torsion test for 20MnCr5 (case hardened steel) and S48C (induction hardened shaft). Test results were comparable with 20MnCr5 (case hardened steel). Also after test a metallurgical inspection was done on an S48C (induction hardened shaft).