Search Results

With advancement of technologies, upgradation of validation procedures and equipment on engine dynamometer test bed is required to simulate environment similar to vehicle and achieve accurate test results. A coolant conditioning system helps in achieving desired temperatures of coolant in the circuit during engine validation. However, unlike radiator type cooling systems of vehicles, conventional coolant conditioning systems on engine test beds generate negative pressure in circuit which poses a risk of coolant boiling, loss of intended heat transfer and hence higher temperature in cylinder head which can be detrimental for durability of critical components like valves, valve seats etc. This paper encompasses a stepwise approach followed to attain near-vehicle coolant pressure conditions for a naturally aspirated engine. Coolant used for this experiment was 50:50 (by volume) ethylene glycol and water mixture.

In the modern automobile scenario in developing countries, customers are getting more meticulous and market more competitive. Now even the budget vehicle customer expects desirable vehicle performance in specific use cases of the vehicle that were previously not focused by designers. Hence, the focus on perceived quality challenges automobile engineers to go the extra mile when it comes to the cost-effective design of parts that are tangible to the customer. A vehicle's cowl cover is one such exterior component. The primary functions of this part are to provide air intake opening for the HVAC system and cover the components like wiper motor. The aesthetic function is to cover the gaps between windshield, hood, and fender as seamlessly as possible. A specific role of cowl cover, which calls for a designer's attention, is its load-bearing capability.

Three-cylinder Engine without balancer shaft is a recent trend towards development of lightweight and fuel-efficient powertrain for passenger car. In addition, customer's expectation of superior NVH inside vehicle cabin is increasing day by day. Engine mounts address majority of the NVH issues related to transfer of vibration from engine to passenger cabin. Idle vibration isolation for a three-cylinder engine is a challenging task due to possibility of overlapping of Powertrain's rigid body modes with engine's firing frequency. This Overlapping of rigid body can be avoided either by modifying mount characteristic or by changing the position of mounts based on multi-body-dynamics (MBD) simulation. This paper explains about two types of engine mounting system for a front-wheel drive transversely mounted three-cylinder engine. The base vehicle was having three-point mounting system i.e. all three engine mounts were pre-loaded.

In automotive Front End Accessory Drives (FEAD), the crankshaft supplies power to accessories like alternators, pumps, etc. FEAD undergoes forced vibration due to crankshaft excitation, dynamic tension fluctuations can cause the belt to slip on the accessory pulleys. By considering the criticality of the system, when engine mounting is longitudinally to the vehicle which makes it directly exposed to the air flow containing foreign particles which may cause the damage to the FEAD system and deteriorate the intended functionality. FEAD cover is introduced in the system to enhance belt-pully system functionality by restricting the entry of foreign particles during engine operation. This paper contains a study of FEAD cover failure and provides the stepwise approach to capture such issue during novel model development for 4 cylinder naturally aspirated engine during engine bench testing.

With strict upcoming regulation norms, it becomes a challenging task for automotive industry to develop highly efficient engine that meets all the regulation requirements. The focus of automakers is to utilize fuel energy in most efficient way and to reduce the energy loss from the engine to improve thermal efficiency. Heat loss to the cooling medium is one of the prime losses inside the combustion chamber. Thermal barrier coating is used to reduce heat losses across combustion chamber surfaces (Piston, head, valves and cylinder liner) as it provides good insulation because of the prominent properties of coating materials like low thermal conductivity, low heat capacity, high melting point etc. This paper presents application and impact of thermal swing coating on thermal efficiency. Thermal swing coating material follows gas temperature quickly throughout the cycle which reduces the temperature difference between gas and coating surface and thus reduces the heat loss.

To sustain market leadership position one has to continuously improve their product and services so that on one hand customer expectations are met and on the other hand business profitability is maintained. Value engineering is one of the approach through which we can achieve these two objectives simultaneously. Enhancing the value of running products is always a challenge as there is limited scope and flexibility to modify the current design and processes. Value engineering approach, integrated in product development cycle, brings great opportunity to upgrade the new and running products. This study reveals approach to upgrade the base engine of Maruti Alto. Upgraded engine is used in Alto 800 vehicle launched in October 2012. Improvement points were studied based on the business requirement, market competition, and legislative requirements. Based on functional improvement points, all the design parameters were studied and finalized.

Road/Tire noise is an important product quality criterion for passenger cars which are driving customers to decide upon the selection of a vehicle. Reduced engine noise and improvement in road conditions has resulted into more road/tire noise problem as average vehicle speed has gone up. Excitations from road surface travelling through the tire/suspension to vehicle body (structure-borne path) and air-pumping noise caused by tread patterns (air-borne paths) are the main contributor to tire noise issue inside the vehicle cabin [1]. A lot of emphasis is put on the component level design as well as its compliance with vehicle structure to reduce the cabin noise. The objective of this work is to establish a methodology for evaluating structure-borne road/tire noise by evaluating the tire structural behavior and its interface with the vehicle body and its suspension system and identifying the contributing critical paths.

Automobile Catalyst are used to convert Harmful gases emitted by vehicle (CO, HC, and NOx) to less Harmful gas (CO2, H2O and N2), Catalyst Loading comprises of Platinum, Palladium and Rhodium (Rare earth metals) metal powders combined in slurry and wash-coated onto a ceramic brick. Ever since the introduction of BS6 Emissions norm (stricter emission regulation), Catalyst loading content has increased in all vehicles. The Price of these rare earth metal are increasing day by day. Typically, a BS6 regulation catalyst contains a few grams of loading content. In some vehicles there are more than one catalyst (due to regulation requirement) and in some cases catalysts are also located in the underbody, in such cases, Number and location of catalyst makes the vehicle an easy target for thieves. Recently local police authorities around the country have captured many catalysts theft gangs.

Vehicle Hood being the face of a passenger car poses the challenge to meet the regulatory and aesthetic requirements. Urge to make a saleable product makes aesthetics a primary condition. This eventually makes the role of structure optimization much more important. Pedestrian protection- a recent development in the Indian automotive industry, known for dynamics of cost competitive cars, has posed the challenge to make passenger cars meeting the regulation at minimal cost. The paper demonstrates structure optimization of hood and design of peripheral parts for meeting pedestrian protection performance keeping the focus on low cost of ownership. The paper discusses development of an in-house methodology for meeting Headform compliance of a flagship model of Maruti Suzuki India Ltd., providing detailed analysis of the procedure followed from introduction stage of regulatory requirement in the project to final validation of the engineering intent.

Riding comfort for automobile seating can be classified into two categories, long time riding comfort and short term riding comfort. The attributes that govern the riding comfort includes static spring constant and energy lost due to hysteresis. The emerging trend towards long term riding comfort could be governed by the above mentioned factors. The hysteresis loss characteristic is related to Poly-Urethane (PU) properties used extensively in automotive seating application. The nature with which the energy is released considering the same material and varying the hardness directly contributes to the comfort analysis for automobile seating and vice versa. Two curves can define the same area but the loading and unloading trend for the two cases could be different and so be the riding comfort. A conclusion would be drawn by obtaining hysteresis loss rate by changing the different parameters (hardness, density). One parameter would be varied by keeping the others constant.

Manual transmissions dominate the Indian market for their obvious benefit of low cost and higher mechanical efficiency resulting in higher fuel economy. Synchronizer system in manual transmission enables smoother and quieter gear shifting. Synchronizer ring is the key element which provides the necessary frictional torque to synchronize the speed of gear and sleeve for smooth shifting. During vehicle running, synchronizer rings are free to rattle inside the indexing clearance. High engine torsional excitation and low clutch dampening can result into increased fluctuation of the input shaft of transmission. High fluctuation or lower contact area of synchronizer ring can lead to damage on the index area. This damage may cause hard gear shifting and gear shift blockage in case of extreme damage.

As the automotive market is very dynamic and vehicle manufactures try to reduce the vehicle development cycle time, more focus is being given to CAE simulation technologies to reduce the design cycle time and number of physical tests. CAE engineers are continuously working on improving the accuracy of CAE simulation, such as using flexible body dynamic simulation in place of linear static analysis. Strength calculation under dynamic condition is more accurate as compared to static condition as it gives more clear understanding of stress variation with motion, contacts and mass inertia. Failure has been observed in new development of valve train pivot screw under test conditions. As per linear static analysis, design was judged OK. Normal linear static analysis is a two stage process. In first stage loads are calculated by hand or peak loads are taken from multibody dynamics (MBD) rigid body analysis.

Risk of injury to occupant in the event of side impact is considerably higher compared to frontal or rear impact as the energy absorbing zones at the front and rear of vehicle is high whereas limited space is available to dissipate the impact energy in the event of side impact. In such scenario strength of side door plays an important role in protecting the occupant. Side door beam in door structure contributes significantly towards the lateral stiffness and plays dominant role in limiting the structural intrusion into passenger compartment. Hence it is interesting to understand the effect of beam specification and orientation on side door strength. Since these factors not only affect the strength but also the cost and weight targets, their study and analysis is important with respect to door design This paper showcases the effect of beam layout and its specifications on the overall strength of the door with an experimental approach using physical test.

Electrostatic charge generation in fabric is a common phenomenon. This phenomenon of charge generation & transfer of the same to human body is more in case of fabrics made of polyester yarns due to interface property of the material. The charge generation may result in attraction of dust on the fabric surface, clinginess & may also result in uncomfortable shock to the human body. This situation is attributed to various parameters such as fabric construction, yarn properties, yarn finish & various coating on the yarn. Since, polyester fabric is prime material used in seating; there have been many incidences of rubbing of seat fabric to human body, resulting in generation of static charge. This study focuses on understanding the effect of various fabric parameters on electrostatic charge generation. The study will also look into various potential solutions to reduce the charge generation with their merits and demerits.

The interface between human body and automotive seat contours is seat upholstery. Seating comfort has a functional correlation to the upholstery. Two seats having different upholstery will give different comfort perception. Even an ergonomically designed seat if fitted with poor quality fabric will subdue the seat comfort drastically. The effect of fabric comfort ranges from initial short term to long term comfort, driven by properties like wick-ability and factors like thermal stress. Beyond material characteristics, fabric fit also plays an important role. This paper analyses the effect of fabric parameters and construction on automotive seat comfort. A comprehensive comparative study is followed by systematic analysis and comfort improvement scope through upholstery. The research is to conclude potential of the seat fabric in enhancing the automotive seating comfort within stipulated constraints of fabric properties and cost.

Shorter product development cycles, densely packed engine compartments and intensified noise legislation has increased the need for accurate predictions of passenger cars Exhaust system noise at early design stages. The urgent focus on the increasing CO2 emissions and the efficiency of IC-engines as well as upcoming technologies might adversely affect the noise emission from an exhaust system, so it is becoming increasingly important to evaluate the sub system level noise emissions in an early design stage in order to predict and optimize the exhaust system performance. Engine performance and vehicle NVH characteristics are two important parameters on which the design of the exhaust system has major influence. The reduction of exhaust noise is a very important factor in controlling the exterior and interior noise levels of vehicles, particularly to reach future target values of the pass-by noise and sound engineering for the vehicle.

Over the years, Fuel efficiency and cabin comfort of vehicle has become increasingly important in buying decision and can significantly give competitive edge to the vehicle in marketplace. Weight and friction reduction of rotating and reciprocating components in engines is one of the proven approaches to improve the efficiency of internal combustion engine. To reduce the friction, the general approach is to use low viscosity engine oils, improve the surface finish and reduce the contact area of sliding elements, switch over from sliding contact to rolling contact etc. However sometimes this approach has adverse impact on engine NVH characteristics due to occurrence of abnormal transient noise due to mechanical knocking of the components in specific operating conditions.

Hybrid Electric Vehicle (HEV) Controls Development is an important aspect to realize the goals of Powertrain Electrification i.e. fuel economy and emission improvement. Keeping that in mind, development engineers need to formulate numerous control strategies. Once the control strategy is evaluated and frozen, it typically does not change from one vehicle model application to another. However, it may happen that Electronic Control Unit (ECU) manufacturer may change depending on the sourcing strategy. Therefore, in order to maintain uniformity, it may be required to compare control strategy of a finished ECU product frozen for one model application to be compared with new ECU sourced through another manufacturer. This paper discusses a methodology to compare control strategy of two ECU’s sourced from different ECU manufacturers with identical control requirements.

Due to intense peak summer temperatures and sunny summers in tropical countries like India etc., achieving the required thermal comfort of car occupants without compromising on fuel efficiency is becoming increasingly challenging. The major source of heat load on vehicle is Solar Load. Therefore, a study has been conducted to evaluate the heat load on vehicle cabin due to solar radiations and its impact on vehicle air-conditioning system performance with various combinations of door glasses and windscreen. The glasses used for this study are classified as green, dark green, dark gray, standard PVB (Polyvinyl Butyral) windscreen and PVB windscreen having infrared cut particles. For each glass, part level evaluation was done to find out the percentage transmittance of light of different wavelengths and heat flux through each glass.

In order to meet the challenges of future CAFE regulations & pollutant emission, vehicle fuel efficiency must be improved upon without compromising vehicle performance. Optimization of engine breathing & its impact on vehicle level fuel economy, performance needs balance between conflicting requirements of vehicle Fuel Economy, performance & drivability. In this study a Port Fuel Injection, naturally aspirated small passenger car gasoline engine was selected which was being used in a typical small passenger car. Simulation approach was used to investigate vehicle fuel economy and performance, where-in 1D CFD Engine model was used to investigate and optimize Valve train events (Intake and exhaust valve open and close timings) for best fuel economy. Engine Simulation software is physics based and uses a phenomenological approach 0-D turbulent combustion model to calculate engine performance parameters. Engine simulation model was calibrated within 95% accuracy of test data.