Search Results

Due to the integration of many interacting subsystems like hybrid vehicle management, energy management, distance management, etc. into the VCU platform the design steps for function development and calibration become more and more complex. This makes an aid necessary to relieve the development. Therefore, the aim of the proposed simulation-based development and calibration design is to improve the time-and-cost consuming development stages of modern VCU platforms. A simulation-based development framework is shown on a complex function development and calibration case study using an advanced powertrain concept with a plug-in hybrid electric vehicle (PHEV) concept with two electrical axles.

The consequent means towards improved enhancement of the safety of commercial vehicles will in future times require more and more electronic intelligence, in case a distinct optimization of the systems will not be possible with conventional means. In forefront, endeavours are aimed at the improvements of the functions of the system in regard to driving safety, as well as driver stress relief at lowest possible costs, in order to increase the total cost effectiveness of commercial vehicles. Starting with currently implemented electronic systems up to systems now under development, a continuous development of standalone electronics up to integrated electronic compounding is the current trend. This trend shows advantages of reduced wiring and the number of sensors while it increases the function at the same time.

Economical and technical aspects justify intelligent suspension systems in commercial vehicles. The tasks of suspensions of vehicles are contradictionary and the prevailing problems cannot be readily solved with conventional suspension systems in a satisfying manner. However, advantages are acquired by the use of adaptive suspension systems. Varying the properties and characteristics of suspension systems in respect to the different loads transported by a commercial vehicle, to vehicle speeds and to dynamic maneuvers, nearly present as good results as closed loop controlled adaptive suspension systems do. For economical reasons fully active suspension systems are only installed in commercial vehicles performing special tasks and services. Partially active suspension systems reduce power consumption and demonstrate satisfactory efficiency.

In order to adhere with future automotive legislation and incentives, the electric range of plug-in hybrids has steadily increased. At the same time, the installed electric power has risen as well leading to future hybrid vehicles with an electric power share of more than half of overall system power and hybrid configurations with at least two electrical machines come into focus. The concept of adding a separate electrical axle to a P2-hybrid - a so called P24-hybrid, is of special interest. The system complexity of a such a system increases significantly as the number of possible system states increases. Thus, this paper analyzes the efficiencies and benefits of the different system states within the fuel-optimal operating strategy derived by global optimization. By varying the electrical power distribution between the two axles, the impact on fuel efficiency and the changes within the operating strategy are investigated.

The electric range of plug-in hybrids as well as the installed electric power has steadily increased. With an electric power share of more than half of the overall system power, concepts of hybrid electric vehicles with at least two electric machines come into focus. Especially the concept of adding an individual electric axle to a state-of-the-art parallel hybrid, such as a P2-hybrid, is promising. However, the system complexity of a so-called P24-hybird increases significantly because the number of possible system states rises. This leads to an increased development and calibration effort for an online energy management. Especially a transfer from an optimized operating strategy to a rule-based energy management is challenging. Thus, a development framework for the calibration of an online energy management system (EMS) which is as fuel efficient as possible is needed.

Due to the continuous electrification of vehicles, the variety of different hybrid topologies is expected to increase in the future. As the calibration of real-time capable energy management systems (EMS) is still challenging, a development framework for the EMS that is independent of the hybrid topology would simplify the overall development process of hybrid vehicles. In this paper an analytical methodology, which is used to derive a fuel-optimal, rule-based EMS for parallel hybrids, is transferred to a series topology. It is shown that the fundamental correlations can be applied universally to both parallel and series configurations. This enables the possibility to develop a real-time capable, rule-based controller for a series HEV based on maps that ensures a fuel-optimal operation. These maps provide the optimal power threshold for the activation of the auxiliary power unit and the optimal power output dependent on the driver’s power request.

The recent advance in the development of various hybrid vehicle technologies comes along with the need of establishing optimal energy management strategies, in order to minimize both fuel economy and pollutant emissions, while taking into account an increasing number of state and control variables, depending on the adopted hybrid architecture. One of the objectives of this research was to establish benchmarking performance, in terms of fuel economy, for real time on-board management strategies, such as ECMS (Equivalent Consumption Minimization Strategy), whose structure has been implemented in a SIMULINK model for different hybrid vehicle concepts.

The current legislation for industrial applications and construction equipment including earthmoving machines and crane engines allows different strategies to fulfill the corresponding exhaust emission limits. Liebherr Machines Bulle SA developed their engines to accomplish these limits using SCRonly technology. IAV supported this development, carrying out engine as well as SCR aftertreatment system and vehicle calibration work including the OBD and NOx Control System (NCS) calibration, as well as executing the homologation procedures at the IAV development center. The engines are used in various Liebherr applications certified for EU Stage IIIb, EPA TIER 4i, China GB4 and IMO MARPOL Tier II according to the regulations “97/68/EC”, “40 CFR Part 1039”, “GB17691-2005” and “40 CFR Parts 9, 85, et al.” using the same SCR hardware for all engine power variants of the corresponding I6 and V8 engine families.

Rear axle steering systems electronically controlled and hydraulically actuated are discussed for commercial vehicles. With these steered axles, the major objective is to improve the manoeuvrability of these vehicles. With the aid of the steering strategy “Rear end Swing-out Compensation” it will be assured, that in two-axle, all-wheel steering trucks dangerous rear end swing-out effects, occuring primarily in low speed ranges, will not take place. In addition, it is possible to enhance the dynamic stability of two-axle trucks while braking on split adhesion road surfaces with the aid of specific control algorithms. Furthermore, the application of a rear axle steering system can suppress dangerous lateral oscillations of centre-axle trailers.

The development of energy efficient air conditioning systems for electric vehicles is an ever increasing challenge, because the cooling as well as the heating of the passenger compartment reduces the cruising range dramatically. Electric cars are usually equipped with a scroll compressor and a separate electric motor with appropriate power electronics. However, this solution is critical in terms of the installation space, the weight and also the costs. Therefore, an innovative and energy efficient drivetrain structure for electric vehicles was developed, which integrates the motor of the A/C-compressor directly into the drivetrain. Thus it is possible to switch off the compressor motor and to use the main motor for the drive of the compressor at certain driving situations. As a result, the operating point of the main motor can be shifted to a better efficiency.

To achieve low emission levels, the handicap of the TWC is its light-off characteristic. It achieves a maximum hot efficiency of nearly 100 %, but this requires a temperature in the range of 300 to 450 °C. To improve this time lag after cold start, the TWC needs additional help to reach the targets of future low (LEV) or ultra low emission (ULEV) levels. This paper describes the work on additional devices to reach the ULEV-levels such as: Electrical Heated Catalyst (EHC). Burner Heated Catalyst (BHC) Hydrocarbon Trap (HCT) as external device. Adsorber Coated Substrate (ACS) in the usual converter box. The comparison of these systems was done with a concept car. The low mileage exhaust results demonstrated the principal suitability of all these devices, but there is still much work to be done to meet the ULEV levels with the guaranted durability. The advantages and disadvantages of the systems are discussed, including estimated weight and cost.

Tires of modern commercial vehicles must meet a specific requirement profile, containing the economic aspects, ride comfort and driving safety, as well. These three primary criteria are discussed in this paper, whereby emphasis is placed on the force transmission behavior of commercial vehicle tires regarded as a variable directly associated to driving safety. At the same time, the influence of distinct parameters such as wheel load, road speed, tire inflation pressure, tread depth and coefficient of adhesion between tire and road on the lateral and braking force behavior is illustrated using steady state and dynamic measurements. They were carried out on real roads using a specially prepared mobile tire dynamometer, but on an indoor drum-type tire test stand, as well. In addition to the above mentioned parameter variations the differences of the results on account of the test method are analysed.

The powertrain electrification is currently not only taking place in public road mobility vehicles, but is also making its way to the racetrack, where it’s driving innovation for developments that will later be used in series production vehicles. The current development focus for electric vehicles is the balance between driving power, range and weight, which is given even greater weighting in racing. To redefine the current limits, IAV developed a complete e-powertrain for a racing MX motorcycle and integrated it into a real drivable demonstrator bike. The unique selling point is the innovative direct phase-change cooling (PCC) of the three-phase e-motor and its power electronics, which enables significantly increased continuous power (Pe = 40 kW from 7,000 rpm to 9,000 rpm) without thermal power reduction. The drive unit is powered by a replaceable Lithium-Ion round cell battery (Ubat,max = 370V) with an energy storage capacity of Ebat = 5 kWh.

In January 1996 Mercedes-Benz has introduced a new 4-cylinder engine OM 904 LA of the new engine family for light commercial vehicles. The power range of the OM 904 LA comprises ratings from 90 kW up to 125 kW at 2300 rpm. From the beginning of the design of this engine, a noise emission output as low as possible was strived for, aside from the high targets as far as durability, maintenace and fuel consumption are concerned. The basis is the development of noise regulations for commercial vehicles. The noise reduction measures have to be concentrated on the engine since up to now it still is one of the main noise emission sources at the vehicle. Already at the lay-out of the engine the prerequisits for a low-noise engine behaviour have been taken into consideration. The engine is equipped with a fuel injection system featuring particular unit injector pumps for each cylinder which is superior to the conventional in-line injection pump as far as acoustics are concerned.

This paper proposes a current limits distribution control strategy for a parallel hybrid electric vehicle (parallel HEV) which includes an advanced powertrain concept with two electrical driving axles. One of the difficulties of an HEV powertrain with two electrical driving axles is the ability to distribute the electrical current of one high voltage battery appropriately to the two independent electrical motors. Depending on the vehicle driving condition (i.e., car maneuver) or the maximization of the entire efficiency chain of the system, a suitable control strategy is necessary. We propose an input-output feedback linearization strategy to cope with the nonlinear system subject to input constraints. This approach needs an external, state dependent saturation element, which translates the state dependent control input saturation to the new feedback linearizing input and therefore preserves the properties of the differential geometric framework.

The automotive world is progressing fast towards autonomous vehicles making sensors one of the critical components. There is a requirement for constant exchange of information between the vehicle and its surrounding environment, which is assisted by sensors such as Camera, LiDAR, and RADAR. However, exposure to harsh environmental conditions such as rain, dirt, snow, and bird droppings can hamper the functioning of the sensors and in turn interrupt accurate vehicle maneuvers. Sensor-cleaning mechanisms are required to be tested under various weather conditions and vehicle operating situations. Besides wind tunnel tests, digitalizing this whole process becomes important to take decision on design changes in early vehicle development stage. This work presents a digital methodology to test the LiDAR cleaning system in the advent of mud clearing at different vehicle speeds. The cleaning mechanism consists of a telescopic nozzle placed above the LiDAR translating back and forth.

The settings of adaptive suspension elements may be switched from a comfortable “soft” characteristic to a safe and “firm” characteristic. Thus the possibility is given to not only improve the ride comfort, but the dynamic driving behavior as well, since no compromise must be made between these two criteria when tuning the suspensions. Such systems seem to be very promising for commercial vehicles, as - because of their changing loading conditions - it is very difficult to design an optimal suspension system using conventional springs and dampers. This paper describes the influence of shock absorbers and air springs with variable characteristics on the ride comfort and the dynamic behavior of a 15-t-truck by investigations done with a simulation system. A series production vehicle without adaptive suspension elements serves as basis. At first the results of measurements and simulations are compared and show a very good concurrence.

In particular on heavy duty commercial vehicles, the continuous braking systems “engine braking system” and “retarder”, which are independent of the service braking system, are installed to handle the continuous braking load on downhill stretches. These systems are also used to reduce lining wear and thermal loads of the service braking system. Exhaust braking systems are the most widely used form of engine braking systems. The current state-of-the-art in retarders is represented by two basic concepts, the electrodynamic retarder and the hydrodynamic retarder. A performance comparison of the different systems shows that low mountain descending speeds are the domain of engine braking systems, whereas retarders are more effective for medium and high descending speeds. The electrodynamic retarder is more favourable for lower road speeds, while the hydrodynamic retarder develops its effectiveness during higher downhill speeds.

One challenge for the development of commercial vehicles is the reduction of CO2 greenhouse, where hydrogen can help to reduce the fleet CO2. For instance, in Europe a drop in fleet consumption of 15% and 30% is set as target by the regulation until 2025 and 2030. Another challenge is EURO VII in EU or even already approved CARB HD Low NOx Regulation in USA, not only for Diesel but also for hydrogen combustion engines. In this study, first the requirements for the combustion and after-treatment system of a hydrogen engine are defined based on future emission regulations. The major advantages regarded to hydrogen combustion are due to the wide range of flammability and very high flame speed numbers compared to other fossil based fuels. Thus, it can be well used for lean burn combustion with much better fuel efficiency and very low NOx emissions with an ultra lean combustion. A comprehensive experimental investigation is performed on a HD 2 L single-cylinder engine.

The newest legislative trends enforce a significant decrease in CO2 emissions for commercial vehicles. For instance, in Europe a drop in fleet consumption of 15% and 30% is set as target by the regulation by 2025 and 2030. The use of carbon-neutral fuels offers possibilities regarding net-zero CO2 emissions - although not yet considered by the rules. Another challenging aspect is the drastic tightening of NOx emissions limits for future legislations, which is approved or being discussed both for the United States and for the EU. The current work describes the potentials of an innovative fuel, marketed as Gane fuel regarding performance, efficiency and emission behavior. First, the properties of the developed fuel are described: Gane is made from methanol blended with water and is tailored for diffusive combustion. The fuel blending is so defined to fulfill the combustion requirements.