Search Results

In developing a direct injection gasoline engine, the in-cylinder fuel air mixing is key to good performance and emissions. High speed visualization in an optically accessible single cylinder engine for direct injection gasoline engine applications is an effective tool to reveal the fuel spray pattern effect on mixture formation The fuel injectors in this study employ the unique multi-hole turbulence nozzles in a PFI-like (Port Fuel Injection) fuel system architecture specifically developed as a Low Pressure Direct Injection (LPDI) fuel injection system. In this study, three injector sprays with a narrow 40° spray angle, a 60°spray angle with 5°offset angle, and a wide 80° spray angle with 10° offset angle were evaluated. Image processing algorithms were developed to analyze the nature of in-cylinder fuel-air mixing and the extent of fuel spray impingement on the cylinder wall.

Challenges that persons with disabilities face with current modes of transportation have led to difficulties in carrying out everyday tasks, such as grocery shopping and going to doctors’ appointments. Autonomous vehicles have been proposed as a solution to overcome these challenges and make these everyday tasks more accessible. For these vehicles to be fully accessible, the infrastructure surrounding them need to be safe, easy to use, and intuitive for people with disabilities. Thus, the goal of this work was to analyze interview data from persons with disabilities, and their caregivers, to identify barriers to accessibility for current modes of transportation and ways to ameliorate them in pick up/drop off zones for autonomous vehicles. To do this, interview subjects were recruited from adaptive sports clubs, assistive living facilities, and other disability networks to discuss challenges with current public transit stops/stations.

This paper presents results from experiments performed in an axisymmetric water analog model of a four-stroke IC engine using the optical velocimetry technique LIPA (Laser Induced Photochemical Anemometry). The investigation can be described as a fundamental scientific inquiry into the fluid dynamics encountered during engine operation, with the long term goal of increasing performance. An application of LIPA to a fluid dynamics problem delivers two-dimensional fields of velocity vectors which are projections of the full three-dimensional vectors in single measurement steps. From an evaluation of a velocity field vorticity information can be obtained readily. Velocity fields and vorticity distributions are, in this study, the basis for the evaluation of seven parametric quantities. Some of these may become tools that give engineers ‘rule of thumb’ indications of the mixing that is occurring.

Numerous studies have documented that lower extremity injury is second only to the head and face in automotive accidents. Such injuries are common because the lower extremity is typically the first point of contact between the occupant and the car interior. Of all lower extremity injuries, the knee is the most common site of trauma. This typically results from high speed contact with the instrument panel which can produce fracture and subfracture (contusions, lacerations, abrasions) level injuries. Current Federal safety guidelines use a bone fracture criterion which is based solely on a peak load. The criterion states that loads exceeding 10 kN will likely result in gross bone fracture. However, cadaver experiments have shown that increased contact area (via padding) over the knee can significantly increase the amount of load that can be tolerated before fracture or subfracture injury.

High frequency variations in crankcase pressure have been observed in Inline-four cylinder (I4) engines and an understanding of the causes, frequency and magnitude of these variations is helpful in the design and effective operation of various engine systems. This paper shows through a review and explanation of the physics related to engine operation followed by comparison to measured vehicle data, the relationship between crankcase volume throughout the engine cycle and the observed pressure fluctuations. It is demonstrated that for a known or proposed engine design, through knowledge of the key engine design parameters, the frequency and amplitude of the cyclic variation in crankcase pressure can be predicted and thus utilized in the design of other engine systems.

Driver and passenger comfort, as related to automotive seats, is a growing issue in the automotive industry. As this trend continues, automotive seat designers and developers are generating a greater need for more anthropometrically accurate tools to aid them in their work. One tool being developed is the JOHN software program that utilizes three-dimensional solid objects to represent humans in seated postures. Contours have been developed to represent the outside skin surfaces of three different body types in a variety of postures in the sagittal plane. These body types include: the small female, the average male, and the large male.

Injuries to the lower extremities are common during car accidents because the lower extremity is typically the first point of contact between the occupant and the car interior. While injuries to the knee, ankle and hip are usually not life threatening, they can represent a large societal burden through treatment costs, lost work days and a reduced quality of life. The aim of the current study was to specifically study injuries associated with the knee and to propose a methodology which could be used to prevent future knee injuries. To understand the scope of this problem, a study was designed to identify injury trends in car crashes for the years 1979-1995. The NASS (National Accident Sampling System) showed that 10% of all injuries were to the knee, second only to head and neck injuries. Most knee injuries resulted from knee-to-instrument panel contact. Subfracture injuries were most common (contusions, abrasions, lacerations) followed by gross fracture injuries.

In an effort to create computer models to promote rapid, cost-effective prototyping while easing design changes, more information about how people interact with seats is needed. Predicting the occupant location, their geometry, and motion within a vehicle leads to a better determination of safety restraint location, controls reach, and visibility - factors that affect the overall operation of the vehicle. Based on the Michigan State University JOHN model, which provides a biomechanical simulation of the torso posture, experiments were conducted to examine the change of postures due to seat and interior package factors. The results can be incorporated into the posture prediction model of the RAMSIS program to give a more detailed prognosis of the spine curvature and refine the model-seat interactions. This paper will address findings of the experimental study with relation to model development.

Seat factors are characteristics of seats that influence people's postures. Seat factors such as lumbar prominence and seat pan stiffnesses were defined and measured for a variety of automotive seats. Seat factors such as these serve as a basis for evaluating and comparing seats. They were useful for selecting seats and designing experiments for human subject testing in the ASPECT program. Seat factors are also candidates for independent variables in statistical posture prediction models. The Seat factors described in this paper were measured with the current J826 manikin. They will be redefined for use with the new ASPECT manikin.

To assist automotive seat development and evaluation, a technique for predicting the posture of seated occupants has been developed. The method involved modeling the torso geometry and articulation of a mid-size male, based on information presented in SAE paper number 930110 [1]. This mid-size male model, known as 2-D JOHN, was developed in a commercial kinetic modeling software and used in a comparative seat evaluation study between a current production automotive seat and a prototype articulating seat. The 2-D JOHN model was supported a greater range of postures, defined as Total Lumbar Curvature (TLC) and Torso Recline Angle (TRA), in the prototype seat than the automotive seat.

Large Eddy Simulations of atomization and evaporation of liquid fuel sprays in diesel engine conditions are performed with stochastic breakup and non-equilibrium droplet heat and mass transfer models. The size and number density of the droplets generated by the breakup model are assumed to be governed by a Fokker-Planck equation, describing the evolution of the PDF of droplet radii. The fragmentation intensity spectrum is considered to be Gaussian and the scale of Lagrangian relative velocity fluctuations is included in the breakup frequency calculations. The aerodynamic interactions of droplets in the dense part of the spray are modeled by correcting the relative velocity of droplets in the wake of other droplets. The stochastic breakup model is employed together with the wake interaction model for simulations of non-evaporating and evaporating sprays in various gas temperature and pressure conditions.

Deformations of soft tissues and seat cushion foam are significant factors in determining the interface contours between the seat and the back of the thigh. This paper describes the measurement of forces, deformations, and contours of people's thighs and seat cushion materials. The goal of this work is to represent the human interactions with seats. A two-dimensional, plane strain finite element method was used to develop a contact model between the cross section of the human mid-thigh and flat surfaces, which can be a flat, rigid surface or a flat, foam cushion of various thicknesses and densities. Results of human and seat interactions for various subjects were measured, modeled, and compared. The present work showed a good agreement between experiments and models for various subjects and foam densities. The important results showed that the stiffness of the foam does not depend on the foam thickness.

Internet worms have shown the capability to compromise millions of network hosts in a matter of seconds, thereby precluding human countermeasures. A worm over a vehicular ad hoc network (VANET) can, in addition to the well-known threats, pose a whole new class of traffic-related threats (ranging from congestion to large-scale accidents). To combat these automated adversaries, security patches can be distributed by good worms. An accurate VANET-based worm propagation model is essential to protect from malicious worms and to efficiently utilize good worms for distribution of security patches. This paper derives an approximate closed-form mathematical model of worm propagation over VANETs. Simulation results assert that the proposed model captures the VANET worm propagation dynamics with outstanding accuracy.

EGR coolers are used in combustion engines to reduce NOx emissions. However, heat transfer in these coolers also results in thermophoresis-temperature-gradient driven motion of suspended particles towards cooler regions-which leads to significant soot deposition. A simple one-dimensional model is proposed to predict the deposition velocity and soot layer thickness that compares reasonably well with experimental data. The behavior of soot deposits on cooled surfaces is complex, with the thickness of the soot layer stabilizes after around 100 hours, reaching a uniform, thickness over the entire heat-exchanger surface. An analysis of this trend and a tentative mechanism to explain this type of behavior is given, based on experimental observations.

Piston temperature plays a major role in determining details of fuel spray vaporization, fuel film deposition and the resulting combustion in direct-injection engines. Due to different heat transfer properties that occur in optical and all-metal engines, it becomes an inevitable requirement to verify the piston temperatures in both engine configurations before carrying out optical engine studies. A novel Spot Infrared-based Temperature (SIR-T) technique was developed to measure the piston window temperature in an optical engine. Chromium spots of 200 nm thickness were vacuum-arc deposited at different locations on a sapphire window. An infrared (IR) camera was used to record the intensity of radiation emitted by the deposited spots. From a set of calibration experiments, a relation was established between the IR camera measurements of these spots and the surface temperature measured by a thermocouple.

Camless Variable Valve Actuation (VVA) technologies have been known for improving fuel economy, reducing emissions, and enhancing engine performance. VVA can be divided into electro-magnetic, electro-hydraulic, and electro-pneumatic actuation. A family of camless VVA designs (called LGD-VVA or Gongda-VVA) has been presented in an earlier SAE publication (SAE 2007-01-1295) that consists of a two-spring actuation, a bypass passage, and an electrohydraulic latch-release mechanism. The two-spring pendulum system is used to provide efficient conversion between the moving mass kinetic energy and the spring potential energy for reduced energy consumption and to be more robust to the operational temperature than the conventional electrohydraulic actuation; and the electrohydraulic mechanism is intended for latch-release function, energy compensation and seating velocity control.

Since the 1960's, automotive seats have been designed and evaluated with tools and procedures described in the SAE Recommended Practice J826. The SAE J826 design template and testing manikin each have a torso with a flat lower back shape and with a single joint at the H-point. The JOHN models provide a more anatomically detailed representation of human shape and movement. The articulations of the JOHN torso (pelvic, lumbar, and thoracic) segments are coupled so that their relative positions are determined by a single parameter related to spinal curvature. This paper describes the development and use of the JOHN biomechanical models for seating design.

This paper presents a review of the core functions and decisions of transportation and traffic management in the automobile industry. Its purpose is to present the concepts within a revised framework which is set in a logistical channels context. Using this approach it easier to see the interdependence which is necessary between shippers and carriers that handle raw materials, component parts, and finished products.

Injury to the lower extremity during an automotive crash is a significant problem. While the introduction of safety features (i.e. seat belts, air bags) has significantly reduced fatalities, lower extremity injury now occurs more frequently, probably for a variety of reasons. Lower extremity trauma is currently based on a bone fracture criterion derived from human cadaver impact experiments. These impact experiments, conducted in the 1960's and 70's, typically used a rigid impact interface to deliver a blunt insult to the 90° flexed knee. The resulting criterion states that 10 kN is the maximum load allowed at the knee during an automotive crash when certifying new automobiles using anthropomorphic dummies. However, clinical studies suggest that subfracture loading can cause osteochondral microdamage which can progress to a chronic and debilitating joint disease.

Understanding cylinder-kit tribology is pivotal to durability, emission management, reduced oil consumption, and efficiency of the internal combustion engine. This work addresses the understanding of the fundamental aspects of oil transport and combustion gas flow in the cylinder kit, using simulation tools and high-performance computing. A dynamic three-dimensional multi-phase, multi-component modeling methodology is demonstrated to study cylinder-kit assembly tribology during the four-stroke cycle of a piston engine. The percentage of oil and gas transported through different regions of the piston ring pack is predicted, and the mechanisms behind this transport are analyzed. The velocity field shows substantial circumferential flow in the piston ring pack, leading to blowback into the combustion chamber during the expansion stroke.