Search Results

Without engine noise, the cabin of an electric vehicle is quiet, but on the other hand, it becomes easy to perceive refrigerant-induced noise in the automotive air-conditioning (A/C) system. When determining the A/C system at the design stage, it is crucial to verify whether refrigerant-induced noise occurs in the system or not before the real A/C systems are made. If refrigerant-induced noise almost never occurs during the design stage, it is difficult to evaluate by vehicle testing at the development stage. This paper presents a 1D modeling methodology for the assessment of refrigerant-induced noise such as self-excitation noise generated by pressure pulsation through the thermal expansion valve (TXV). The GT-SUITE commercial code was used to develop a refrigerant cycle model consisting of a compressor, condenser, evaporator, TXV and the connecting pipe network.

OBD (On Board Diagnosis) has been applied to detect malfunctions in powertrains. OBD requirements have been extended to detect various failures for ensuring the vehicle emission control system being normal. That causes further costs for additional sensors and software works. Two layers diagnosis system is proposed for a passenger car gearbox system to detect changes from normal behavior. Conventional physical constraints based diagnosis is placed on the base layer. Model based diagnosis and specific symptom finding diagnosis are built on the second layer. Conventional physical constraints based diagnosis is direct and effective way to detect the failure of system if the detected signals exceed their normal ranges. However under the case of system failure with related signals still remain in normal ranges, the conventional detection measures can not work normally. Under this case, Model based diagnosis is proposed to enhance the functionality of diagnosis system.

Downsizing engines with a turbocharging system have been widely applied to passenger cars to improve fuel economy. Engine torque response to accelerator operation is one of important features in addition to steady state performance of the system. Torque profile management for turbocharged internal combustion engines is one of required technologies. A turbocharging system for a car is a system with a positive feedback loop in which compressed air drives the compressor after the combustion process. A reduced order model was derived for the charging system. Pressure ratio of a compressor is proportional to square of turbine speed and the turbine speed is a first order delay system to throttle opening in the model. Model structure was designed from mathematical equations that describe turbine and compressor works. Model parameters were identified from measured data. An output torque profile control strategy based on the derived model is investigated.

Torque profile control is one of required technologies for propulsion engines. A smaller parametric model is more preferable for control algorithm design and evaluation. Mean value engine torque can be obtained from throttle opening change using a transfer function. A transfer function for a turbocharged engine was investigated with thermo-dynamic equations for a turbine and a compressor and test data. A small turbocharged engine was tested to model the air transfer process. Turbine speed was measured with temperatures, pressures and air mass flow. Turbine speed response is like a first order system to air mass flow into a combustion chamber. The pressure ratio at the compressor is approximated by a curve proportional to the turbine speed square. Based on those findings, a reduced order model for describing dynamic air transfer process with a turbocharger was constructed. The proposed model is compact and suitable for engine torque control design and controller implementation.

To apply a fuel economy performance to AT&CVT fluid for common use (hereinafter AT/CVT fluid) and manual transmission fluid, by optimizing fluid viscosity, a fundamental study was investigated. Generally, it is well known that the viscosity of polymer-added transmission fluids is gradually reduced, due to deterioration of the viscosity index improver caused by shear stress. An excessive viscosity reduction causes an operation failure or damage to the transmission. Considering above factor, the authors focused attention on the potential of a low viscosity formulation to improve fuel efficiency by reducing an internal stirring-resistance of the transmission. Also from the viewpoint of friction characteristics, the performance of a base oil was studied. Utilizing the EHL (Elast-Hydrodynamic Lubrication) tester [1] and vehicle tests, the performance of base oils was evaluated for the fluid development.

Compression ratio of newly developed gasoline engines has been increased in order to improve fuel efficiency. But in-cylinder pressure around top dead center (TDC) before spark ignition timing is higher than expectation, because the low temperature oxidization (LTO) generates some heat. The overview of introduced calculation method taking account of the LTO heat of unburned gas, how in-cylinder pressure is revised and some knowledge of knocking prediction using chemical kinetics are shown in this paper.

A KIVA code which is customized for passenger car's diesel engines is linked with an engine performance simulator and demonstrated with our optimizing calculation system. Aiming to fulfill our target calculation speed, the combustion model of the KIVA code is changed from a chemical reaction calculation method to a chemical equilibrium calculation method which is introduced a unique technique handling chemical species maps. Those maps contain equilibrium mole fraction data of chemical species according to equivalence ratio and temperature. Linking the KIVA code to the engine simulator helps to evaluate engine performance by indicated mean effective pressure (IMEP). The optimizing calculation system enables to obtain response surfaces. Observing the response surfaces, clear views of engine performance characteristics can be seen. The overview of this calculation system and some examples of the calculation are shown in this paper.

A mean value turbocharged engine model is useful in terms of accuracy and convenience for fuel economy strategies or engine controller development. Turbocharging process is a feedback system with a positive gain, i.e. increasing exhaust work leads to increasing a cycle work. The gain of the feedback system is determined mainly by exhaust work ratio in a cycle and inertia of the turbine. The work ratio was investigated based on engine test with EGR. A turbocharging process model was obtained using the work ratio in a cycle and theoretical equations. The model is applied to investigate manifold absolute pressure response with EGR.

Rapid Controller Prototyping (RCP) is an efficient method for design & development of ECU (Electronic Controller Unit) at early stage. Usually, RCP requires firstly performing Software-in-the-loop simulation and then connecting universal controller (e.g. MicroAutoBox) to real controlled system for testing of controller functionality. During this process, it is likely that some problems related to signal configuration and real time characteristics occur and consequently give rise to unexpected results, e.g., sensor signals or controlling signals produce large deviation and possibly damage components of real system under severe condition. On the other hand, it cannot make sure that the real time characteristics of designed controller are suitable just after applying Software-in-the-loop simulation.

The combination of 1D and 3D fluid flow models is achieved using a co-simulation methodology. This realizes that the internal flow in a component simulated in 3D is incorporated into a network (system) containing components represented in 1D. This methodology gives the details of the internal flow while conserving overall mass flow in the system, thus eliminating uncertainties in boundary conditions prescribed in the 3D model and reducing the overall simulation time. This paper shows numerical results for internal flow of water flow circuit of engine cooling system and availability and current problem of 1D/3D co-simulation method are discussed.

Gasoline engines have the trace-knock phenomena induced by the fast combustion which happens a few times during 100 cycles. And that constrains the thermal efficiency improvement due to limiting the ignition timing advance. So the authors have been dedicating a trace-knock simulation so that we could obtain any pieces of information associated with trace-knock characteristics. This simulation consists of a turbulent combustion model, a cycle-by-cycle variation model and a chemical calculation subprogram. In the combustion model, a combustion zone is considered in order to obtain proper turbulent combustion speed through wide range of engine speed. From a cycle-by-cycle variation analysis of an actual gasoline engine, some trace-knock features were detected, and they were involved in the cycle-by-cycle variation model. And a reduced elementary reaction model of gasoline PRF (primary reference fuel) was customized to the knocking prediction, and it was used in the chemical calculation.

To reduce the idling rattle of manual transmissions, the computer simulation has been utilized. However, the conventional simulation model could not express properly the relationship between the transmission oil temperature and the rattle noise level, especially in case of transmission with backlash eliminator in constant mesh gears. In this study, the authors carried out detail experiments investigating the motion of each part in the transmission. Based on the experimental results, an additional mass representing all constant mesh speed gears supported on plain or rolling element bearings was introduced to the simulation model. Using the improved model, it was confirmed that the calculated RMS value of the fluctuation in countershaft angular acceleration corresponds to the experimental rattle noise level.

In recent years, the slip lock-up mechanism has been adopted widely, because of its fuel efficiency and its ability to improve NVH. This necessitates that the automatic transmission fluid (ATF) used in automatic transmissions with slip lock-up clutches requires anti-shudder performance characteristics. The test methods used to evaluate the anti-shudder performance of an ATF can be classified roughly into two types. One is specified to measure whether a μ-V slope of the ATF is positive or negative, the other is the evaluation of the shudder occurrence in the practical vehicle. The former are μ-V property tests from MERCON® V, ATF+4®, and JASO M349-98, the latter is the vehicle test from DEXRON®-III. Additionally, in the evaluation of the μ-V property, there are two tests using the modified SAE No.2 friction machine and the modified low velocity friction apparatus (LVFA).

When developing an airbag system with mechanical sensors, one of the important stages is to get satisfactory correlation between the sensor characteristics and the specific vehicle. This development stage requires control of both vehicle crashworthiness (including selection of sensor mount location) and airbag sensor characteristics. This stage is ordinarily performed through many iterations of a computer simulation which involves the dynamic structure of the sensor mechanism. A new graphic method is proposed in this paper to help in this simulation stage. This method can estimate the proper threshold level of the crash sensor. The airbag sensor mount location in the vehicle can be selected and the airbag sensor can be developed. The validity of the method has been verified by computer simulation as well as actual test results.

Recently, the evaluation of the thermal environment of an engine compartment has become more difficult because of the increased employment and installation of turbochargers. This paper proposes a new prediction model of the momentum source for the turbine of a turbocharger, which is applicable to three-dimensional thermal fluid analyses of vehicle exhaust systems during the actual vehicle development phase. Taking the computational cost into account, the fluid force given by the turbine blades is imitated by adding an external source term to the Navier-Stokes equations corresponding to the optional domain without the computational grids of the actual blades. The mass flow rate through the turbine, blade angle, and number of blade revolutions are used as input data, and then the source is calculated to satisfy the law of the conservation of angular momentum.

Flows around a forward facing step and a fence are simulated on structured grid to estimate aerodynamic noise by using direct simulation. Calculated results of sound pressure level show quantitatively good agreement with experimental results. To estimate aerodynamic noise from 3D complex geometry, a simplified side mirror model is also calculated. Averaged pressure distribution on the mirror surface as well as pressure fluctuations on the mirror surface and ground are simulated properly. However, calculated result of sound pressure level at a location is about 20dB higher than experiment due to insufficient spatial resolution. To capture the propagation of sound waves, more accuracy seems to be required.

The widening of the selectivity windows of a three-way catalyst under A/F ratio modulation was shown to result from retention of adsorbed species on catalyst surfaces and their subsequent reaction with gas-phase reactants. A reaction model was developed based on adsorption properties of CO, HC and NOx and by computer simulation, the conversion efficiencies of CO, HC and NOx under A/F ratio modulation were calculated. The calculated and experimental results were in good agreement.

In this paper, emissions reduction technologies applied to high-speed direct injection (HSDI) diesel passenger car engines to meet the stricter exhaust emission legislation are described. To reduce smoke, the F.I.E. has been improved by using a radial-piston distributor pump which delivers fuel-injection-pressure up to 120MPa. Cooled exhaust gas re-circulation (EGR) system and increase in volume ratio of the combustion chamber has made it possible to increase EGR ratio and reduced nitrogen oxides (NOx) and smoke simultaneously. Furthermore, improvements in the oxidation catalyst activating temperature reduces PM at lower exhaust gas temperatures. As a result of applying these technologies, a clean and economical HSDI diesel engine for passenger cars, which complies with Japanese '98 exhaust emissions legislation and has better fuel economy than indirect injection (IDI) diesel engines (above 15%), has been developed.

Driving car means to control a vehicle according to a target path, e.g. road and speed, with some constraints. Human driving models have been proposed and applied for simulations. However, human control in driving has not been analyzed sufficiently comparing with that of machine control system in term of control theory. Input - output property with internal information processing is not easily measured and described. Response of human driving is not as quicker as that of machine controller but human can learn vehicle response to driving operation and predict target changes. Driving behavior of an expert driver and a beginner in an emission test cycle was measured and difference in target speed tracking was looked into with performance indices. The beginner's operation was less stable than that of the expert. Transfer function of the vehicle system was derived based on linearized model to investigate human driving behavior as a tracking controller in the system.

To research the mechanism of automobile aerodynamic noise which transmits to the inside of a cabin, flow structure and sound field have been investigated by applying experimental measurements at the wind tunnel and computational fluid dynamics (CFD) based on lattice Boltzmann method (LBM). In this research, transmitted noise at a front side window glass is focused. Pressure fluctuations on the side window glass contain both hydrodynamic pressure fluctuations induced by convection of flow field and acoustic pressure fluctuations propagated from noise sources. But it was found that acoustic pressure fluctuations have large contributions on the side window glass at the high frequency range by considering of the experimental transmission loss. On the other hand, at the low frequency range, hydrodynamic pressure fluctuations are dominant, however their effects to transmitted noise are not so influential for high fluctuation levels.