Search Results

The Vehicle Energy Consumption calculation Tool (VECTO) is used for the official calculation and reporting of CO2 emissions of HDVs in Europe. It uses certified input data in the form of energy or torque loss maps of driveline components and engine fuel consumption maps. Such data are proprietary and are not disclosed. Any further analysis of the fleet performance and CO2 emissions evolution using VECTO would require generic inputs or reconstructing realistic component input data. The current study attempts to address this issue by developing a process that would create VECTO input files based as much as possible on publicly available data. The core of the process is a series of models that calculate the vehicle component efficiency maps and produce the necessary VECTO input data. The process was applied to generate vehicle input files for rigid trucks and tractor-trailers of HDV Classes 4, 5, 9 and 10.

The European Union road transport CO2 emissions regulation foresees mandatory targets for passenger vehicles. However, several studies have shown that there is a divergence between official and real-world values that could range up to 40% compared to the NEDC reference value. The introduction of the Worldwide Harmonized Test Protocol (WLTP) limited this divergence, but it is uncertain whether it can adequately address the problem, particularly considering future evolutions of vehicle technology. In order to address this issue, the recent EU CO2-standards regulation introduces the monitoring of on-road fuel consumption and subsequently CO2 emissions by utilizing On-Board Fuel Consumption Meters (OBFCM). In the near future, all vehicles should provide instantaneous and lifetime-cumulative fuel consumption signals at the diagnostics port. Currently, the fuel consumption signal is not always available.

With the adoption of the Worldwide harmonized Light Vehicles Test Procedure (WLTP) and the Real Driving Emissions (RDE) regulations for testing and monitoring the vehicle pollutant emissions, as well as CO2 and fuel consumption, the gap between real world and type approval performances is expected to decrease to a large extent. With respect to CO2, however, WLTP is not expected to fully eliminate the reported 40% discrepancy between real world and type approval values. This is mainly attributed to the fact that laboratory tests take place under average controlled conditions that do not fully replicate the environmental and traffic conditions experienced over daily driving across Europe. In addition, any uncertainties of a pre-defined test protocol and the vehicle operation can be optimized to lower the CO2 emissions of the type approval test. Such issues can be minimized in principle with the adoption of a real-world test for fuel consumption.

The accurate prediction of pollutant emissions generated by IC engines is a key aspect to guarantee the respect of the emission regulation legislation. This paper describes the approach followed by the authors to achieve a strict numerical coupling of two different 1D modeling tools in a co-simulation environment, aiming at a reliable calculation of engine-out and tailpipe emissions. The main idea is to allow an accurate 1D simulation of the unsteady flows and wave motion inside the intake and exhaust systems, without resorting to an over-simplified geometrical discretization, and to rely on advanced thermodynamic combustion models and kinetic sub-models for the calculation of cylinder-out emissions. A specific fluid dynamic approach is then used to track the chemical composition along the exhaust duct-system, in order to evaluate the conversion efficiency of after-treatment devices, such as TWC, GPF, DPF, DOC, SCR and so on.

The fuel supply chain faces challenges associated with microbial contamination symptoms. Microbial growth is an issue usually known to be associated with middle distillate fuels and biodiesel, however, incidents where microbial populations have been isolated from unleaded gasoline storage tanks have also been recently reported. Alcohols are employed as gasoline components and the use of these oxygenates is rising, especially ethanol, which can be a renewable alternative to gasoline, as well. Despite their alleged disinfectant properties, a number of field observations suggests that biodeterioration could be a potential issue in fuel systems handling ethanol-blended gasoline. For this reason, in this study, the effect of alcohols on microbial proliferation in unleaded gasoline fuel was assessed. Ethanol (EtOH), iso-propyl alcohol (IPA) and tert-butyl-alcohol (TBA) were evaluated as examples of alcohols utilized in gasoline as oxygenates.

A vital element of any vehicle-certification test is the use of representative values for the vehicle resistance forces. In most certification procedures, including the WLTP recently adopted by the EU, the latter is achieved mainly through coast down tests. Subsequently, the resistance values measured are used for setting up the chassis-dyno resistances applied during the laboratory measurements. These reference values are obtained under controlled conditions, while a series of corrections are applied to make the test procedure more repeatable and reproducible. In real driving, the actual vehicle road loads are influenced by a series of factors leading to a divergence between the certified fuel consumption values, and the real-world ones. An approach of calculating representative road loads during on-road tests can help to obtain a more unobstructed view of vehicle efficiency and, when needed, confirm the officially declared road loads.

This study investigates the impact of mid-high biodiesel blends on the criteria and PAH emissions from a modern pick-up diesel vehicle. The vehicle was a Euro 4 (category N1, subclass III) compliant common-rail light-duty goods pick-up truck fitted with a diesel oxidation catalyst. Emission and fuel consumption measurements were performed on a chassis dynamometer equipped with CVS, following the European regulations. All measurements were conducted over the certification New European Driving Cycle (NEDC) and the real traffic-based Artemis driving cycles. Aiming to evaluate the fuel impact on emissions, a soy-based biodiesel, a palm-based biodiesel, and an oxidized biodiesel obtained from used frying oils were blended with a typical automotive ultra-low-sulfur diesel at proportions of 30, 50 and 80% by volume. The experimental results revealed that CO₂ emissions and fuel consumption exhibited an increase with biodiesel over all driving conditions.

This paper describes some of the recent work carried out in our laboratory regarding the effects of novel oxygen and nitrogen containing compounds on the antiknock quality of unleaded gasoline and their effects on some other gasoline properties. In particular, the research included Research Octane Number (RON) measurements and the evaluation of the effects of the most effective antiknock compounds on Dry Vapour Pressure Equivalent (DVPE), distillation temperatures, aromatic content, olefins, and oxygen content. Emphasis was given in studying chemical structures that can be derived from renewable raw materials. The compounds tested included substituted phenols, furan derivatives, aliphatic amines, various amide structures and Mannich base phenols. Methyl t-butyl ether (MTBE), the most widespread oxygenate currently used in gasoline, was used as a yardstick for assessing the quality of the compounds tested.

In Plug in hybrid electric vehicles (PHEVs), the management of the main drivetrain components and the shift between pure electric and hybrid propulsion is decided by the on-board energy management system (EMS). The EMS decisions have a direct impact on CO2 emissions and need to be optimized to achieve as low emissions as possible. This paper presents optimization methods for EMS algorithms of a parallel P2 PHEV. Two different supervisory control algorithms are examined, employing simulations on a validated PHEV platform. An Equivalent Consumption Minimization Strategy (ECMS) algorithm is implemented and compared to a rule-based one, the latter derived by back-engineering of available experimental data. The different EMS algorithms are analyzed and compared on an equal basis in terms of distance, demanded energy and state of charge levels over different driving cycles.

This work includes an assessment of the lubricity of Greek road diesel fuel of low sulfur content, and the effect of the addition of two different types of biodiesel which can be produced from raw materials abundant in the Mediterranean area. In this study, a series of representative fuels of the Greek fuel market were tested. In some of them, the lubricity was measured three times, during a period of three months from the day of each sample was produced. In all cases a decrease of the wear scar diameter (WSD) was measured; this behaviour could be attributed to the oxidation reactions that take place during the storage period. In order to monitor the effect of the addition of biodiesel on the lubricity of road diesel, biodiesels produced from sunflower oil and olive oil were used. The use of rape seed oil biodiesel as a diesel fuel substitute is a commercial event in Central Europe; in the United States the soybean oil biodiesel has been examined in detail.

For many years Rancimat was the only standardized method for measuring the oxidation stability of FAME and FAME/diesel blends. However this method is not applicable to pure conventional petroleum products and so the effect of FAME on diesel fuel stability could not be evaluated directly. Recently a Rapid Small Scale Oxidation Test (RSSOT) that covers the determination of the stability of biofuels and petroleum products was developed and standardized. In this study the oxidation stability of seven different types of FAMEs was assessed, either neat or blended with three types of ULSD fuel, by employing both the Rancimat and the RSSOT accelerated oxidation methods. The determinations from either test were analyzed and a comparative assessment of these two method was carried out.

The Diesel engine and especially the direct injection type one is considered to be one of the most efficient thermal engines known to man up to now. It has an efficiency that in some cases is 30 to 40% higher than its competitor the spark ignition engine. The efficiency of the direct injection diesel engine has been considerably improved during the last decade resulting to low fuel consumption and lower absolute values of pollutant emissions. If we consider the green house effect caused by the emitted CO2 it is revealed the environmental importance of high engine efficiency. In the present work a theoretical investigation is conducted using a detailed simulation model for engine performance prediction, to examine the possibilities for improving engine efficiency. The simulation model used is a complete open cycle model for the engine and its subsystems. Such phenomenological models are very suitable for the prediction of engine performance.

The effects of biodiesel oxidation stability on diesel fuel injection equipment (FIE) behavior were investigated using newly developed test rig and methodology. On the test rig, biodiesel blend fuels were circulated through a fuel tank and a common rail injection system. Fuel injected from typical diesel injectors was returned into the fuel tank to enhance the speed of fuel degradation. The results showed that injector deposits could be reproduced on a test rig. It was observed that injector body temperature increase accelerates the degradation of fuel and therefore gives earlier FIE failure. Fuel renewal could partially restore the injection quantity after complete failure at low injection pressure, thus showing a potential cleaning effect on injector deposits when refueling a car.

The Vehicle Energy Consumption calculation Tool (VECTO) is used in Europe for calculating standardised energy consumption and CO2 emissions from Heavy-Duty Trucks (HDTs) for certification purposes. The tool requires detailed vehicle technical specifications and a series of component efficiency maps, which are difficult to retrieve for those that are outside of the manufacturing industry. In the context of quantifying HDT CO2 emissions, the Joint Research Centre (JRC) of the European Commission received VECTO simulation data of the 2016 vehicle fleet from the vehicle manufacturers. In previous work, this simulation data has been normalised to compensate for differences and issues in the quality of the input data used to run the simulations. This work, which is a continuation of the previous exercise, focuses on the deeper meaning of the data received to understand the factors contributing to energy and fuel consumption.

The rare occurrence during city driving of the exhaust temperature levels required for ceramic trap regeneration without catalytic aid, seems to be the main reason of delay in wide application of the trap. The use of catalysts seems to be more or less necessary. Study of the catalytic activity during trap regeneration had not been very effective so far. This holds equally true for the case of catalyzed trap as for the case of catalytic fuel additives. The lack of a satisfactory theory for the explanation and prediction of catalytic activity, directed international research and development towards the quest of the optimum catalyst, which could support a very simple and low-cost regeneration system. The new approach to the explanation of catalytic activity presented in this paper, denies the above assumption.

Renewable substitutes for transportation fuels have had an important role in the recent years. Hydrotreated vegetable oils (HVO) are produced from two stage hydrotreating process of vegetable oils. The second stage of this hydroteating process is used to convert normal paraffins to isoparaffins in order to improve cold flow properties of these fuels. As this stage is a high energy consuming process, it is of interest to investigate the characteristics and the usability of the first stage of hydrotreatment of lipids. This paper examines the properties of alternative fuel derived from the hydrotreatment of used cooking oil (UCO). Used cooking oil is a difficult feedstock for biodiesel production. The hydrotreating of UCO converts triglycerides mainly into normal paraffins within the diesel fuel range. The hydrotreated UCO (HUCO) has an excellent cetane number and cetane index (>90), but very poor cold flow properties.

The scope of this work is to examine the use of hydroprossed used cooking oils as substitute for automotive diesel fuel. Hydroprocessing is an alternative method for the transformation of vegetable oils into high quality transport fuels, even if the quality of the oils is low, such as used cooking oils. In the present work, the utilization of hydroprocessed used cooking oil (HUCO) as neat fuel was proved to be very difficult, due to its very poor cold flow properties; therefore, mixtures of the HUCO with low quality middle distillates (a low cetane number gasoil and a light cycle oil) were prepared and evaluated. Throughout the process the formed blends were evaluated according to the european standard EN 590. The following points were mainly recorded: The lower density of HUCO was beneficial, permitting the use of poor quality distillates, in specific concentrations, and the high cetane number of HUCO was appreciable, improving the worse behavior of the other components.

This paper investigates how different on-board energy management system (EMS) algorithms can affect the total energy consumption considering propulsion, heating, ventilation, and air conditioning (HVAC) operation and thermal comfort requirements. Firstly, an integrated plug-in hybrid electric vehicle (PHEV) powertrain and HVAC model including vehicle cabin has been developed as a demonstrator. Two different EMS algorithms - namely a rule-based and an equivalent consumption minimization strategy (ECMS) one - are applied to the integrated PHEV model and evaluated under different environmental conditions. The results showed that the HVAC system operation affects the total energy consumption benefits when ECMS algorithm is used over the rule-based. ECMS reduces the total energy consumption by 2.5% compared to rule-based without HVAC operation, while the total energy consumption reduction changes to 5.3% and 6.3% when HVAC provides heating and cooling power respectively.

The first two of a series of traps retrofitted on a pilot fleet of 110 buses of the Athens Bus Corporation were removed for examination after 100,000 km of revenue service. These buses were gradually equipped with the ELBO Trap Oxidiser since the beginning of 1989 and are constantly operated on Cerium based fuel additive. The physical properties and the chemical composition of filters and ash residues were analysed by the filter manufacturers and the fuel additive producer. The results have shown that after two years of operation the filter material remained intact and the ash deposits (consisting mainly of CeO2) exhibit a limited interaction with the cordierite. More than 94% of these deposits are filtered by the monoliths and could be removed to a large extent with the application of conventional methods.

To achieve low tailpipe NOX emissions in Heavy-Duty engines, the rapid warm-up of the exhaust aftertreatment system (EAS) needs to be assisted by the adoption of new technologies to reduce engine-out emissions and increase the EAS conversion efficiency. Engine measures like cylinder deactivation, retarded start of the main injection, late intake valve closing, intake throttling and elevated idle speed can substantially increase the available exhaust gas enthalpy and temperature at the expense of additional fuel as has been shown in the literature. On the other hand, the exhaust system can be optimized in terms of hardware and controls, which is nowadays strongly supported by simulation. However, these simulation studies typically assume a fixed engine hardware and calibration and thus fixed engine-out simulation boundary conditions. Moving forward to tougher and real-world oriented legislation, the fixed cycle and engine-out boundary condition becomes insufficient.