Search Results

For reducing exhaust emissions of heavy-duty diesel engines, the authors made an experimental study of diesel combustion using a single cylinder engine. The engine performance and exhaust emissions have been measured using a wide range and high EGR rate under the conditions of high boost intake pressure. The engine test cell has been equipped the external supercharger that is able to raise the boost pressure to 500 kPa, and also equipped the EGR system to increase the EGR rate until 50% under the 500 kPa boost condition. In various test conditions of load and engine speeds the authors have obtained the results, that is, NOx has been reduced drastically without increasing Particulate Matter (PM).

Low NOx combustion is possible by PREDIC (PREmixed lean DIesel Combustion) in which fuel is injected at a very early stage of the compression stroke and the combustion starts at near the top dead center by self-ignition. To simplify the phenomenon of the PREDIC process, the test engine was operated with gaseous fuels added to intake air to realize combustion of a perfectly homogeneous mixture. The rich limit was observed around λ=2.0∼2.4. This limit was determined by considering the increase in NOx, and the steep pressure rise. During high load operations is not only the ignition timing but also the combustion rate should be controlled. By comparing the homogeneous charge and direct injection case, the mixture heterogeneity could be found to have an influence on the ignition timing and combustion rate, the engine speed and injection timing also had an influenced on these.

Previous research in our laboratory has shown that NOx emissions can be sharply reduced by PREDIC (PRE-mixed lean DIesel Combustion), in which fuel is injected very early in the compression process. However some points of concern remained unsolved, such as a large increase in THC and CO, higher fuel consumption, and an operating region narrowly limited to partial loads, compared to conventional diesel operation. In this paper, the causes of PREDIC's problem areas were analyzed through engine performance tests and combustion observation with a single cylinder engine, through fuel spray observation with a high-pressure vessel, and through numerical modeling. Subsequently, measurable improvements were achieved on the basis of these analyses. As a result, the ignition and combustion processes were clarified in terms of PREDIC fuel-air mixture formation. Thus, THC and CO emissions could be decreased by adopting a pintle type injection nozzle, or a reduced top-land-crevice piston.

Typical DI diesel engines operate with fuel injection taking place within a range of about 30 crank angle degrees before top dead center, at the end of the compression stroke. When injection takes place far earlier, at the beginning of the compression stroke, another form of combustion occurs, which we termed PREmixed lean Diesel Combustion, or PREDIC. With PREDIC operation, self-ignition occurs near top dead center and NOx emissions are drastically lower. When ignition occurs, the fuel-air mixture is thought to be nearly homogeneous, with only slight heterogeneity. Appropriate fuel spray formation is very important for successful PREDIC operation. Using a single-zone NOx formation model, calculations showed that the mean excess air ratio in the PREDIC combustion zone was 1.87, which resulted in very low (20 ppm) NOx emissions. Conventional combustion at the same conditions resulted in a mean combustion zone excess air ratio of 0.88.

The biomass fuel is expected to solve the global warming due to a carbon neutral. A rapeseed oil methyl ester (RME) as biomass fuel was selected, and also a low sulfur diesel fuel is tested as reference fuel in this study. The experiments were carried out to improve diesel emissions and engine performance using high boost and high rate EGR system and a common rail injection system in a single cylinder engine. The diesel emissions and engine performance have been measured under the experimental conditions such as charging boost pressure from atmospheric pressure to 401.3kPa maximum and changing EGR rate from 0% to 40% maximum. RME contain about 10 mass % oxygen in the fuel molecule. Furthermore, RME does not contain aromatic hydrocarbons in the fuel. Due to these chemical properties, RME can be used at 40% high EGR condition.

The mixture formation process in a premixed compression ignition engine was numerically analyzed. This study aimed to find out effective injection conditions for lean mixture formation with high homogeneity, since the NOx and soot emissions in the engine are closely related to the mixture homogeneity. To calculate fuel spray behavior, a practical computer code GTT (Generalized Tank and Tube) was employed. In a model for the premixed compression ignition engine, the effects of injection parameters, such as injection timing, initial droplet size, spray angle, injection velocity, nozzle type (pintle and hole) and injection position / direction, on the mixture homogeneity near ignition timing (or TDC) were investigated. To evaluate the homogeneity of the mixture, an index was defined based on the spatial distribution of fuel mass fraction. The fuel vapor mass fractions as well as the homogeneity indices, obtained as a function of time, were compared under various boundary conditions.

Premixed Lean Diesel Combustion (PREDIC) has very low NOx combustion because of early injection timing, for example, at -120 degrees ATDC; however, it has some problems. One problem is that so much fuel spray reaches the cylinder wall, which causes high HC emission and high fuel consumption. The other problem is that compression ignition timing control is difficult due to the dependence on the in-cylinder temperature. To solve these problems, an impingement spray system with two nozzles is attempted to obtain the spray increasing at the center of the combustion chamber instantaneously. This impingement spray system has two nozzles, which are located diagonally. Two sprays, one injected from each side injector, impinge each other at the center of the cylinder to create an air-fuel mixture.That is,this impingement spray system creates the air-fuel mixture by using the penetration of both sides of the sprays instead of early timing injection.

Premixed lean Diesel Combustion (PREDIC) provides low NOx, however, it has some challenges associated with high HC emission, high fuel consumption and difficult timing control of compression ignition. To solve these problems, an impingement spray system with two injectors was tested to obtain positional controllability and larger volume of the air-fuel mixture formation in our previous study. The positional controllability means mainly the fuel mixture formation is the center of the cylinder with some space from the cylinder wall. The larger volume means the fuel mixture formation is leaner air-fuel mixture than that of free spray, which results in a possibility of higher thermal efficiency. Thus, the impingement spray system has a possibility of HC reduction and fuel consumption improvement in PREDIC.

Thermodynamic characteristics of premixed compression ignition combustions were clarified quantitatively by heat balance estimation. Heat balance was calculated from temperature, mole fractions of intake and exhaust gases, mass and properties of fuels. Heat balance estimation was conducted for three types of combustion; a conventional diesel combustion, a homogeneous charge compression ignition (HCCI) combustion; fuel is provided and mixed with air in an intake pipe in this case, and an extremely early injection type PREmixed lean DIesel Combustion (PREDIC). The results show that EGR should be applied for premixed compression ignition combustion to complete combustion at lower load conditions and to control ignition timing at higher load conditions. With an application of EGR, both HCCI and PREDIC showed low heat loss characteristics at lower load conditions up to 1/2 load.