Search Results

The paper addresses some aspects of an ongoing research on a commercial compact excavator. The interest is focused on the analysis and modelling of the whole hydraulic circuit that, beside a load sensing variable displacement pump, features a stack of nine proportional directional control valves modules of which seven are of the load sensing type. Loads being sensed are the boom swing, boom, stick and bucket, right and left track motors and work tools; instead, the blade and the turret swing users do not contribute to the load sensing signal. Of specific interest are the peculiarities that were observed in the stack. In fact, to develop an accurate AMESim modelling, the stack was dismantled and all modules analysed and represented in a CAD environment as 3D parts. The load sensing flow generation unit was replaced on the vehicle by another one whose analysis and modelling have been developed using available design and experimental data.

The paper deals with the Hardware-In-the-Loop based methodology which was adopted to evaluate the dynamic characteristics of Electronic Stability Program (ESP) and Electro-Hydraulic Brake (EHB) components. Firstly, it permits the identification of the time delays due to the hardware of the actuation system. Secondly, the link between the hardware of the hydraulic unit and a vehicle model running in real time permits the objective evaluation of the performance induced by the single components of different hydraulic units in terms of vehicle dynamics. The paper suggests the main parameters and tests which can help the car manufacturer in evaluating ESP hydraulic units, without expensive road tests.

The problem of wing shape modification under loads in order to enhance the aircraft performance and control is continuously improving by researchers. This requirement is in contrast to the airworthiness regulations that constraint stiffness and stress of the structure in order to maintain structural integrity under operative flight conditions. The lifting surface modification is more stringent in those cases, such as UAV configurations, where the installed power is limited but the variety of operative scenario is wider than in conventional aircraft. A possible solution for adaptive wing configuration can be found in the VENTURAS Project idea. The VENTURAS Project is a funded project with the aim of improve the wind turbine efficiency by means of introducing a twisting capability for the blade sections according to the best situation in any wind condition. The blade structure is composed by two parts: 1) internal supporting element, 2) external deformable envelope.

In the powertrain technology, designers must be careful on oil pan design in order to obtain the best noise, vibration and harshness (NVH) performance. This is a great issue for the automotive design because they affect the passengers' comfort. In order to reduce vibration and radiated noise in powertrain assembly, oil pan is one of the most critical components. The high stiffness of the oil pan permits to move up the natural modes of the component and, as a consequence, reduce the sound emission of the component itself. In addition, the optimized shape of the component allows the increase of natural frequency values of the engine assembly. The aim of this study is the development of a methodology to increase the oil pan stiffness starting from a sketch of the component and adding material where it is needed. The methodology is tested on a series of different models: they have the same geometry but different materials.

This paper presents the methodology adopted by Politecnico di Torino Vehicle Dynamics Research Team to obtain objective indices for the evaluation of the comfort during the gear change process. Some test drivers and different passengers traveled on a test vehicle and assigned marks on the basis of their subjective feeling of comfort during the gearshifts. The comparison between the most significant subjective evaluations and the experimental values obtained by the instruments located on the vehicle is presented. As a consequence, some indices (based on physical parameters) to evaluate the efficiency and the comfort of the gearshift process are obtained. They are in good agreement with the subjective evaluations of the drivers and the passengers. The second part of the paper presents a driveline and vehicle model which was conceived to reproduce the phenomena experimented on the vehicle. The experimental validation of the model is presented.

Flow noise produced by the turbulent motion of the exhaust gases is one of the main contributions to the noise generation for a heavy-duty vehicle. The exhaust system has therefore to be optimized since the early stages of the design to improve the engine’s Noise Vibration Harshness (NVH) performance and to comply with legislation noise limits. In this context, the availability of reliable Computational Aero-Acoustics (CAA) methodologies is crucial to assess the noise mitigation potential of different exhaust system designs. In the present work, a characterization of the sound generation in a heavy-duty exhaust system was carried out evaluating the noise attenuation potential of a design modification, by means of a hybrid CAA methodology.

A numerical-experimental analysis of a new generation Common Feeding (CF) fuel injection system, equipped with last generation solenoid injectors that feature pressure-balanced pilot-valves, has been developed. The main feature of the CF system is that it removes the accumulator from the high-pressure layout of the standard Common Rail (CR). In the CF apparatus, the high-pressure pump is connected directly to the injectors, and a small accumulation volume is integrated in the pump high-pressure circuit. The hydraulic performance of the CF system, including the injectors with the pressure-balanced pilot-valve, has been compared with that of the standard CR system in terms of injected masses, fuel leakages, high-pressure and injected flow-rate time histories. A previously developed advanced one-dimensional code for CR type systems has been adapted for the simulation of the CF high-pressure layout.

Autonomous Driving is one of the main subjects of academic research and one important trend in the automotive industry. With the advent of self-driving vehicles, the interest around trajectory planning raises, in particular when a customer-oriented analysis is performed, since more and more the carmakers will have to pay attention to the handling comfort. With that in mind, an experimental approach is proposed to assess the main characteristics of human driving and gain knowledge to enhance quality of autonomous vehicles. Focusing on overtaking maneuvers in a highway environment, four comfort indicators are proposed aiming to capture the key aspects of the chosen paths of a heterogeneous cohort. The analysis of the distribution of these indicators (peak to peak lateral acceleration, RMS lateral acceleration, Smoothness and Jerk) allowed the definition of a human drive profile.

An integrated theoretical and experimental investigation was carried out in order to evaluate the effects that the pump delivery-valve assembly can produce on the performance of a pump-line-nozzle fuel-injection system with a distributor-type pump for automotive diesel engines. Four distinct delivery valves, one constant-pressure valve, one reflux-hole and two relief-volume valves, were separately fitted to the pump and for each configuration of the delivery assembly the system behavior was analyzed under full-load steady-state operations in a wide pump angular-speed range. Fuel injection-rate as well as local pressure time-histories were investigated, paying specific attention to the occurrence and temporal evolution of cavitation phenomena in the pressure pipe and injector nozzle, after the valve closure. The flow across the delivery-valve assembly was theoretically examined in order to ascertain any instability sources as possible causes of cyclic fluctuations.

Traditional CACC systems utilize inter-vehicle wireless communication to maintain minimal yet safe inter-vehicle distances, thereby improving traffic efficiency. However, introducing communication delays generates system uncertainties that jeopardize string stability, a crucial requirement for robust CACC performance. To address these issues, we introduce a decentralized Model Predictive Control (MPC) approach that incorporates Kalman Filters and state predictors to counteract the uncertainties posed by noise and communication delays. We validate our approach through MATLAB Simulink simulations, using stochastic and mathematical models to capture vehicular dynamics, Wi-Fi communication errors, and sensor noises. In addition, we explore the application of a Reinforcement Learning (RL)-based algorithm to compare its merits and limitations against our decentralized MPC controller, considering factors like feasibility and reliability.

A numerical model for simulating a Common Rail Piezo Indirect Acting fuel injection-system under steady state as well as transient operating conditions was developed using a commercial code. A 1D flow model of the main hydraulic system components, including the rail, the rail to injector connecting pipe and the injector, was applied in order to predict the influence of the injector layout and of each part of the hydraulic circuit on the injection system performance. The numerical code was validated through the comparison of the numerical results with experimental data obtained on a high performance test bench of the Moehwald-Bosch MEP2000/ CA4000 type. The developed injection-system mathematical model was applied to the analysis of transient flows in the hydraulic circuit paying specific attention to the fluid dynamics internal to the injector.

Worldwide regulations concerning noise emissions of road vehicles are constantly demanding further reductions of acoustic emissions, which are considered a major environmental health concern in several countries. Among the different sources contributing to noise generation in vehicles equipped with internal combustion engines, exhaust flow noise is one of the most significant, being generated by turbulence development in the exhaust gases, and robust and reliable numerical methodologies for its prediction in early design phases are currently still needed. To this extent, Computational Aero-Acoustics (CAA) can be considered a valuable approach to characterize the physical mechanisms leading to flow noise generation and its propagation, and it could therefore be used to support exhaust system development prior to the execution of experimental testing campaigns.

Development trends in modern Common Rail Fuel Injection System (FIS) show dramatically increasing capabilities in terms of optimization of the fuel injection pattern through a constantly increasing number of injection events per engine cycle along with a modulation and shaping of the injection rate. In order to fully exploit the potential of the abovementioned fuel injection pattern optimization, numerical simulation can play a fundamental role by allowing the creation of a kind of a virtual injection rate generator for the assessment of the corresponding engine outputs in terms of combustion characteristics such as burn rate, emission formation and combustion noise (CN). This paper is focused on the analysis of the effects of digitalization of pilot events in the injection pattern on Brake Specific Fuel Consumption (BSFC), CN and emissions for a EURO 6 passenger car 4-cylinder diesel engine.

Scope of this work is to analyse potentials in terms of efficiency of two pump units belonging to two families: the first intervening on the maximum volume generated by variable volume chambers (e.g. a vane pump where eccentricity is varied), the second that changes the quantity of fluid being sucked or delivered (e.g. a gear pump with variable timing). In more detail the comparison will be established between a vane pump where displacement is varied through eccentricity and an internal gear pump of Gerotor type where flow rate is controlled through a rotating sector that alters the effective geometry of kidney ports. A detailed simulation of the two solutions brings to evidence the advantages of the first approach with respect to the second as confirmed by experimental investigations.

A novel methodology, for the assessment of Dual Clutch Transmission vibrations during gear shifts, is proposed in this paper. It is based on the capability to predict through numerical simulation a typical dynamic quantity used to objectively evaluate the vibrational behavior of a gearbox during experimental tests, i.e. the acceleration of a point on the external surface of the gearbox housing. To achieve this result, a two-step approach is proposed: an accurate simulation of the internal transmission dynamics and an offline uncoupled computation of the gearbox housing acceleration from the output of the simulation. The first step required the definition of a suitable nonlinear lumped parameter model of the car equipped with a DCT that was implemented in Amesim software.

The effect of variations of compression ratio (CR) and injection pressure (IP) on the emissions and performance of a small displacement common rail off-road diesel engine was evaluated. The operating point corresponding to the 5th mode of the ISO 8178 - C1 test cycle (intermediate speed / full load) was considered, since it represents one of the most critical operating conditions as far as exhaust emissions are concerned. The main effect of a reduction of the compression ratio, for a fixed injection timing, was found to be, as expected, an increase in NOx emissions along with a decrease of PM emissions, with a substantial redefinition of the PM-NOx trade-off curve; the choice of a proper value for the start of injection can therefore lead to a better compromise among pollutant emissions, although remarkable variations in BSFC and combustion noise must be taken into account.

Two different modifications of the baseline cylinder head configuration have been designed and experimentally tested on a MultiAir turbocharged gasoline engine, in order to address the issue of the poor in-cylinder turbulence levels which are typical of the Early-Intake-Valve-Closing (EIVC) strategies which are adopted in Variable Valve Actuation systems at part load to reduce pumping losses. The first layout promotes turbulence by increasing the tumble motion at low valve lifts, while the second one allows the addition of a swirl vortex to the main tumble structure. The aim for both designs was to achieve a proper flame propagation speed at both part and full load. The experimental activity was initially focused on the part load analysis under high dilution of the mixture with internal EGR, which can allow significant further reductions in terms of pumping losses but, on the other hand, tends to adversely affect combustion stability and to increase cycle-to-cycle variations.

The paper presents experimental and theoretical investigations on a shaft mounted gerotor lubricating pump aimed at reducing radiated noise at high engine speed. Effects of noise generation identified as main sources are the fluid borne noise (FBN) that originates in unsteady flow and related pressure fluctuations and structure borne noise (SBN) as a result of pressure transients occurring internally, which cause vibrations of the pump case. To clarify the onset of large delivery pressure fluctuations detected at high pump speed (in excess of 4000 rpm), and validate simulation results (AMESim environment), experimental and theoretical studies have been performed.

Scope of this work is the analysis of the energy consumed by lubricating gear pumps for automotive applications during a driving cycle. This paper presents the lumped parameter simulation model of gerotor lubricating pumps and the comparison between numerical outcomes and experimental results. The model evaluates the power required to drive the pump and the cumulative energy consumed in the driving cycle. The influence of temperature variations on leakage flows, viscous friction torque and lubricating circuit permeability is taken into account. The simulation model has been validated by means of a test rig for hydraulic pumps able to reproduce the typical speed, temperature and load profiles during a NEDC driving cycle. Experimental tests, performed on a crankshaft mounted pump for diesel engines, have confirmed a good matching with the simulation model predictions in terms of instantaneous quantities and overall energy consumption.

This paper explores the potentiality of reducing noise and vibration of a vehicle transmission thanks to powertrain control integration with active braking. Due to external disturbances, coming from the driver, e.g. during tip-in / tip-out maneuvers, or from the road, e.g. crossing a speed bump or driving on a rough road, the torsional backlashes between transmission rotating components (gears, synchronizers, splines, CV joints), may lead to NVH issues known as clonk. This study initially focuses on the positive effect on transmission NVH performance of a concurrent application of a braking torque at the driving wheels and of an engine torque increase during these maneuvers; then a powertrain/brake integrated control strategy is proposed. The braking system is activated in advance with respect to the perturbation and it is deactivated immediately after to minimize losses.