Search Results

The modern solution of two-stage combustion, namely the Turbulent Jet Ignition, enables the combustion of ultra-lean mixtures. Thanks to this solution, it became possible to reduce fuel consumption and, at the same time, to increase the combustion process indicators (including the overall combustion system efficiency). The article presents the results of numerical tests of a heavy-duty engine equipped with the TJI system running on hydrogen fuel. The operating conditions of the Heavy-Duty engine at n = 1500 rpm and IMEP = 10 bar with a prechamber with 7 holes were analyzed. The research was conducted with the use of lean mixtures (global lambda ca. 2 or more). The AVL FIRE software was used to perform the analysis of different fuel doses delivered to the main chamber, with a constant global excess air coefficient value. Increasing the proportion of hydrogen in the pre-chamber resulted in its reduction in the main chamber.

The motor vehicle is one of the main sources of pollutant emissions, especially in urban areas. Environmentally friendly fuels are regarded as very effective means to decrease emissions. With regard to diesel engines, the reduction in nitrogen oxides and particulates are major problem areas. Although the fuel influence on NOx is comparatively low, the composition and parameters of diesel fuel have a big influence on particulate emissions and composition. Sulphur content is one of fuel proprieties, which has the most considerable influence on particulates. This paper describes results of the research on particulate emissions from diesel engines fuelled with research fuels of differing sulphur content. The sulphur content of the research fuels varied from 2000 ppm through 350 ppm (EURO III) and 50 ppm (EURO IV limit, which will be in force in the European Community from 1 January 2005) up to less than 5 ppm.

There is a growing appreciation for using buses powered by alternative fuels in urban transport. Considered as such are city bus with engines fuelled with LNG and hybrid bus. This article, as shown above, provides a comparison of road exhaust emissions from three city buses: one with a CI engine fuelled with diesel fuel, and the other with a SI engine fuelled with LNG and Hybrid bus. Both vehicles (CI and LNG) conformed to Euro VI emission standard (hybrid bus EEV), and the tests were carried out in real traffic conditions. Equivocal opinions about differences in emissions from those types of buses, among others - CO2 and NOx emissions, were the underlying cause of the tests. The comparative study was carried out along the same urban routes during bus trips over the following days in similar traffic conditions. Exhaust road emission was determined based on the vehicle's curb weight and route length, and operating fuel consumption.

The article describes issues related to the impact of transport means on the environment. These issues are currently very popular due to the increasing public awareness of the negative environmental and health effects associated with air pollution. The authors estimated specific emissions in passenger-kilometers, considering a domestic travel by air and road transport. The analyzed route is located between the Polish cities: Gdansk and Cracow. The selected route is long by domestic travel standards, but in that travel distance, the road transport is still competitive to the air transport. Selected means of transport belong to popular representatives in their classes. As a road vehicle, the authors selected a modern passenger car powered by a spark ignition engine, meeting the Euro 6 emission standard. Among the passenger aircrafts, an object which belongs small jet aircrafts, propelled with Rolls-Royce Tay 611C jet engines was selected.

The great reduction in future diesel engine emission limits, especially PM and NOx, forces one to develop means to comply with stringent legislation. Environmentally friendly fuels are regarded as a very effective means to decrease emissions. Although the emission reduction is less than could be achieved by the most modern engine technology or alternative fuels, the immediate net effect of reformulated diesel fuel on emissions is significant, as it takes place over the whole vehicle population. The experimental results presented in this paper were obtained within a research program investigating the effect of different fuels upon emissions from compression-ignition automotive engines. The research were carried out in the laboratories of the BOSMAL Automotive R & D Centre in co-operation to Institute of Internal Combustion Engines at Poznan University of Technology. The partial results of this research program were presented in SAE Paper 2002-01-2219.

Non-Road machines constitutes a large group of machines designed for various tasks and mainly using CI engines for propulsion. This category includes vehicles with drive systems of a maximum capacity of several kilowatts as well as with drives with a capacity of up to thousands of kilowatts depending on the purpose of the machine. Within this group, mobile machines referred to as NRMM (Non-Road Mobile Machinery) stand out. Numerous studies of scientific institutions in Europe and around the world have proven the differences between the exhaust emissions tested in type approval tests and the actual emissions in this group of vehicles. They result from differences in operating points (crankshaft speed and load) of engines during their operation. A big problem is also their considerable age and degree of wear. Approval standards themselves are less stringent than those of heavy-duty vehicles (HDVs), although the engines have similar design and performance.

The tests related to the exhaust emissions from non-road vehicles are currently performed on a chassis dynamometer under the name of NRSC (ISO 8178) and NRTC. In light of the growing requirements related to the environment protection in transport the authors recommend determining the exhaust emissions through real vehicle operating conditions. The tests carried out under real operating conditions could be used for the process of optimization of future power trains of regular road vehicles and non-road vehicles. What is more, these tests should be taken into account in the works on the changes of the legislation related to the emission limits from combustion engines. The paper presents the results of the tests on the exhaust emissions from an agricultural harvester engine and a tractor engine in real operating conditions. The harvester operation during the test consisted in crops collection from the field and the tractor operation during the test consisted in plowing.

The benefits associated with the use of oxygen-containing diesel fuels in passenger cars are quite well described in the literature. This work describes the results of an 18-meter EEV city bus fueled with diesel fuel with the addition of 10% v/v of triethylene glycol dimethyl ether. This compound was chosen because it was effective in reducing exhaust emissions from light duty diesel vehicles. Emission tests (CO, HC, NOx and PM) of the city bus were performed over SORT (Standardized On-Road Tests) cycles using portable exhaust gas analyzers - PEMS. Significant differences in the emission of exhaust components were observed in individual SORT cycles. The level of road emissions reduced as the traffic smoothness increased, i.e. from the SORT 1 to SORT 3 cycle. The largest reduction in bus emissions associated with the use of the oxygenated additive (triethylene glycol dimethyl ether) applies to carbon monoxide and ranges from 50% for the SORT 3 cycle up to 90% for the SORT 1.

In order to measure the concentration of toxic compounds a mobile analyzer for toxic tests SEMTECH DS by SENSORS Inc. was used. In the study the results of the vehicle emission tests in the road conditions were presented as this was the only way to obtain the information on real vehicle emissions. They include information on the emissivity of the vehicles in operation and deal with the real conditions of the vehicle motion. Reliable measurement results were obtained which were verified in simulated conditions on a chassis test bed. The obtained data were used to specify the dependence characteristics for the influence of the dynamic engine properties on the harmful compound emissions. The dynamic engine properties were indirectly taken into account using all the speed range and the range of acceleration calculated for the city traffic in order to prepare a matrix of emission intensity.

The aim of this work was a preliminary discernment of the possibility of application of Pd-Au-Ag-Ni-Co (non Pt) nanometric, powder alloy as an active part of a new PM filter. The hollow part structure of TiO2-x-RuO2-x has been proposed as the active layer on the catalyst support, composed of SiC. This structure is used in the catalyst technology. The washcoat of TiO2-x-RuO2-x has been obtained by the Flame Spray Pyrolysis Deposition method (FSPD). The influence of the preparation conditions such as: flow velocity, salt concentration, temperature and process atmosphere on the size and shape of TiO2-x-RuO2-x particles has been determined. The catalyst alloy contains nanoparticles of Pd-Au, which encapsulated the nanoparticles of Ag and Ni. Such prepared nano-particles containing noble metals or metals 4d (Ni, Co, Ag), show high tolerance to sulfur and good reversible properties. The atoms of Pd prefer five coordinated sites of Ti for adsorption.

One of the main issues in the development of diesel engines is the NOx emission while the chief cause for such emission is high nitrogen content in the air and high temperature of combustion. There is a variety of methods to reduce this particular emission. One of the most widespread is exhaust gas recirculation and one of the most recent is the application of Adblue additive into the exhaust gases as a reducing agent. There are also catalytic converters capable of reducing the said emission but their efficiency is as yet insufficient. One of the more daring related concepts is the elimination of nitrogen from the air supplied to the combustion chamber through the application of ceramic ionic conductors. The technology applied in the last method is a dynamically advancing trend in material engineering. The development in this field indicates that, soon, an oxygen generator useful in the automotive engineering will become a reality.

This paper discusses the importance of the inclusion of emissions from the cold start event during legislative on-road tests on passenger cars (RDE - real driving emissions tests conducted under real-world driving conditions, as defined by EU legislation). Results from a recently-registered gasoline-powered vehicle are presented, with the main focus on the comparison of exhaust emission results: excluding/including the cold start during the initial phase of the RDE test. Cold start is the most challenging aspect of emissions control for vehicles with spark ignition engines and the inclusion of the cold start event in RDE test procedure has wide-ranging implications both for the testing process and compliance with RDE legislation via optimisation of aftertreatment systems and the engine calibration. In addition to some theoretical arguments, the results of an RDE-compliant test performed using the aforementioned procedures are presented.

European Union RDE (real driving emissions) legislation requires that new vehicles be subjected to emissions tests on public roads. Performing emissions testing outside a laboratory setting immediately raises the question of the impact of ambient conditions - especially temperature - on the results. In the spirit of RDE legislation, a wide range of ambient temperatures are permissible, with mathematical moderation (correction) of the results only permissible for ambient temperatures <0°C and >+30°C. Within the standard range of temperatures (0°C to +30°C), no correction for temperature is applied to emissions results and the applicable emissions limits have to be met. Given the well-known link between the thermal state of an engine and its emissions following cold start, ambient temperature can be of great importance in determining whether a vehicle meets emissions requirements during an RDE test.

The paper presents the results of tests on a combustion engine of an armored modular vehicle 8x8 Rosomak under combat simulating conditions. For the measurements of the toxic compounds a portable SEMTECH DS analyzer by SENSORS was used. The analyzer allowed a measurement of toxic compounds at the same time measuring the mass flow rate of the exhaust gases. The analysis of the PM emission was performed based on the measurement of the size of the particulate matter (analyzer 3090 EEPS - Engine Exhaust Particle Sizer™ Spectrometer - by TSI Incorporated) and counting of the particles (analyzer Particle Counter by AVL). The measurements of CO, HC, NOx, PM and fuel consumption were performed under the conditions of combat simulation and in the overboost mode. Based on the obtained results, an analysis of the engine and vehicle operation was performed and the on-road and unit exhaust emissions as well as on-road and unit fuel consumption were compared.

Exhaust gas aftertreatment systems can, under certain conditions, create undesired chemical species as a result of their elimination reactions. A prime example of this is ammonia (NH3), which is not formed in the combustion reaction, but which can be formed within a three-way catalyst (TWC) when physicochemical conditions permit. The elimination of NOx in the TWC thus sometimes comes at the cost of significant emissions of NH3. Ammonia is a pollutant and a reactive nitrogen compound (RNC) and NH3 emissions should be analyzed in this context, alongside other RNC species. Examination of the literature on the subject published over the past two decades shows that ammonia, a species which is currently not subject to systematic emissions requirements for road vehicles in any market, is often identified as forming the majority of the RNC emissions under a range of operating conditions.

Research on the influence of oxygenated diesel fuels on the PM/NOx emission trade-off was carried out with use of 11 different synthetic oxygenated compounds, representing 3 chemical groups (glycol ethers, maleates, carbonates). Each of oxygenates were evaluated as a fuel additive at a concentration of 5% v/v in the same base diesel fuel. The tests were conducted on a passenger car equipped with a common rail turbocharged diesel engine over the European cycle NEDC and US FTP-75 cycle. All the tested oxygenates caused a reduction in PM emissions and most of them caused a certain increase in NOx emissions. The changes in emissions depended on the oxygenate type and cycle. In general, the favorable and unfavorable influence of oxygenated compounds was more intensive during the NEDC, which is a softer and less transient cycle than the FTP-75. The most favorable changes in the PM/NOx emission trade-off were obtained for maleates and carbonates.