Search Results

The octane appetite of an SI engine can be expressed in terms of an Octane Index: OI = (1−K) RON + K MON where K is a constant for a given operating condition and depends only on the pressure and temperature variation in the engine (it is not a property of the fuel). Experimental measurements of K values can be costly and time consuming. This paper reports the development of a new K-value simulation method that can be applied to any spark ignition engine given basic engine data. Good agreement between simulation and experimental results suggests the method is reliable and can be applied to a wide range of engines.

A series of viscous and surface friction modifier additives has been studied in a modified SI engine with separable valve train lubrication. From the results, it has been possible to classify the hydrodynamic or boundary lubrication nature of the observed effects for a series of lubricant additives. It is shown that the frictional benefit of a given additive depends not only on the engine operating condition but also on the engine components on which it is acting. For some additives a fuel economy benefit can switch to a disbenefit as operating regime changes and a different aspect of the additive properties becomes important. Such observations are rationalised in the context of conventional lubrication theory.

Downsized turbocharged gasoline direct injection (TGDI) engines with high specific power and torque can enable reduced fuel consumption in passenger vehicles while maintaining or even improving on the performance of larger naturally aspirated engines. However, high specific torque levels, especially at low speeds, can lead to abnormal combustion phenomena such as knock or Low-Speed Pre-Ignition (LSPI). LSPI, in particular, can limit further downsizing due to resulting and potentially damaging mega-knock events. Herein, we characterize the impacts of lubricant and fuel composition on LSPI frequency in a TGDI engine while specifically exploring the correlation between fuel composition, particulate emissions, and LSPI events. Our research shows that: (1) oil composition has a strong impact on LSPI frequency and that LSPI frequency can be reduced through a carefully focused approach to lubricant formulation.

Carbonaceous deposits can accumulate on various surfaces of the internal combustion engine and affect its performance. The porous nature of these deposits means that they act like a “sponge”, adsorbing fuel components and changing both the composition and the amount of fuel in the combustion chamber. Here we use a previously developed and validated model of engine deposits to predict adsorption of normal heptane, isooctane, toluene and their mixtures in deposits of different origin within a port fuel injected spark ignition engine (Combustion Chamber Deposits, or CCDs, and Intake Valve Deposits, or IVDs) and under different conditions. We explore the influence of molecular structure of adsorbing species, composition of the bulk mixture and temperature on the uptake and selectivity behaviour of the deposits. While deposits generally show high capacity toward all three components, we observe that selectivity behaviour is a more subtle and complex property.

Deposits forming in the injector nozzle holes of modern diesel cars can reduce and disrupt the fuel injected into the combustion chamber, causing reduced or less efficient combustion, resulting in power loss and increased fuel consumption. A study of the factors affecting injector nozzle tip temperature, a parameter critical to nozzle deposit formation, has been conducted in a Peugeot DW10 passenger car bench engine, as used in the industry standard CEC F-098 injector nozzle deposit test, [1]. The findings of the bench engine study were applied in the development of a Chassis Dynamometer (CD) based vehicle test method using Euro 5 compliant vehicles. The developed test method was refined to tune the conditions as far as practicable towards a realistic driving pattern whilst maintaining sufficient deposit forming tendency to enable test duration to be limited to a reasonable period.

Due to the recent drive to reduce CO₂ emissions, the turbocharged direct injection spark ignition (turbo DISI) gasoline engine has become increasingly popular. In addition, future turbo DISI engines could incorporate a form of charge dilution (e.g., lean operation or external EGR) to further increase fuel efficiency. Thus, the conditions experienced by the fuel before and during combustion are and will continue to be different from those experienced in naturally aspirated SI engines. This work investigates the effects of fuel properties on a modern and prototype turbo DISI engine, with particular focus on the octane appetite: How relevant are RON and MON in predicting a fuel's anti-knock performance in these modern/future engines? It is found that fuels with high RON and low MON values perform the best, suggesting the current MON requirements in fuel specifications could actually be detrimental.

Previously reported tests (SAE 2005-01-3839) suggest that lubricant oxidative stability can be improved by running a spark ignition engine with fuels rich in light olefins (e.g. from a catalytically cracked refinery stream). To further our understanding, we have modelled the influence of fuel chemistry on the kinetics of lubricant oxidation. In the hypothesis presented here, the olefins interfere with key chain branching reactions in the lubricant oxidation process and react to form epoxides, which are sufficiently volatile to leave the lubricant. The modelling also predicts that ethanol has a directionally beneficial effect on lubricant oxidative stability. The effect of this will be limited because ethanol is much less soluble in lube-oil under prevailing engine conditions than heavier hydrocarbon components.

Worldwide, Fuel Economy (FE) legislation increasingly influences vehicle and engine design, and drives friction reduction. The link between lubricant formulation and mechanical friction is complex and depends on engine component design and test cycle. This Motored Friction Tear Down (MFTD) study characterizes the friction within a 3.6L V6 engine under operating conditions and lubricant choices relevant to the legislated FE cycles. The high-fidelity MFTD results presented indicate that the engine is a low-friction engine tolerant of low viscosity oils. Experiments spanned four groups of engine hardware (reciprocating, crankshaft, valvetrain, oil pump), five lubricants (four candidates referenced against an SAE 0W-20) and five temperature regimes. The candidate lubricants explored the impact of base oil viscosity, viscosity modifier (VM) and friction modifier (FM) content.

We review some of the key tribological issues of relevance to motorsport applications. Tribology is the science of friction and wear, and in a high performance engine, friction and wear are controlled by good component design (e.g. the engine and the transmission) and also by the use of high performance lubricants with the correct physical (and chemical) properties, matched to the machine they are used in. In other words, design of a specific lubricant for specific hardware can lead to optimised performance. (Tribology is also important in the tire-road contact but are not considered here.) The importance of key physical properties of a lubricant is demonstrated with an emphasis on how the choice of the correct lubricant can help to minimize engine friction (and thus increase available power output) whilst protecting against engine wear. Key lubricant parameters discussed in the paper are the viscosity variation of a lubricant with temperature, shear rate and pressure.

In the present study, Large Eddy Simulations (LES) have been performed with a 3D model of a step nozzle injector, using n-pentane as the injected fluid, a representative of the high-volatility components in gasoline. The influence of fuel temperature and injection pressure were investigated in conditions that shed light on engine cold-start, a phenomenon prevalent in a number of combustion applications, albeit not extensively studied. The test cases provide an impression of the in-nozzle phase change and the near-nozzle spray structure across different cavitation regimes. Results for the 20oC fuel temperature case (supercavitating regime) depict the formation of a continuous cavitation region that extends to the nozzle outlet. Collapse-induced pressure wave dynamics near the outlet cause a transient entrainment of air from the discharge chamber towards the nozzle.

A European test procedure for evaluating engine deposits, using the Mercedes Benz M111 bench engine, has already been approved for inlet valve deposits (IVD) and is under development for combustion chamber deposits (CCD) by the Co-ordinating European Council (CEC). This paper describes CCD effects on emissions using a slightly modified version of this engine test procedure and compares it with CCD/emissions data from road vehicles. The engine used was a modern four valve, four cylinder, 2.0 litre passenger car unit and the bench test procedure used extended the operating time from the specified 60 hours to 180 hours. The road vehicle trial used two Mercedes Benz C200 passenger cars fitted with the M111 engine and two Ford Mondeo 2.0 litre passenger cars. Data was collected up to 11200km, approximately equivalent to 180 hours operation of the bench engine.

The paper discusses the concept, design and final results from the ‘Ultra Boost for Economy’ collaborative project, which was part-funded by the Technology Strategy Board, the UK's innovation agency. The project comprised industry- and academia-wide expertise to demonstrate that it is possible to reduce engine capacity by 60% and still achieve the torque curve of a modern, large-capacity naturally-aspirated engine, while encompassing the attributes necessary to employ such a concept in premium vehicles. In addition to achieving the torque curve of the Jaguar Land Rover naturally-aspirated 5.0 litre V8 engine (which included generating 25 bar BMEP at 1000 rpm), the main project target was to show that such a downsized engine could, in itself, provide a major proportion of a route towards a 35% reduction in vehicle tailpipe CO2 on the New European Drive Cycle, together with some vehicle-based modifications and the assumption of stop-start technology being used instead of hybridization.

For gasoline spark ignition engines, port fuel injection (PFI) on a global basis remains the most common type of fuel delivery. When operated with lower quality fuels and lubricants, PFI engines are prone to suffering from the build-up of harmful deposits on critical engine parts including the inlet valves. High levels of inlet valve deposits (IVDs) have been associated with drivability issues like engine stumble and hesitation on sudden acceleration. Fuels formulated with the appropriate level of deposit control additive (DCA) can maintain engine cleanliness and even remove deposits from critical components. This study, involving a single cylinder research bench engine operated in PFI injection mode and heavily augmented with measurement equipment, aimed to gain a deeper understanding of the detrimental impacts of IVDs on engine efficiency and performance.