Search Results

A road test has been conducted to quantify the benefits provided by a high-performance gasoline additive package in a fleet of cars representative of Europe, SE Asia, and South America. The emissions, fuel consumption, and engine cleanliness benefits of additised versus untreated gasoline were compared in 15 pairs of cars. A further 6 cars were operated on a mixture of fuels to show the benefits of additised fuel versus mixed fuelling. The design of the experiment was based on a similar road test conducted in 1991. Through careful test design and execution, it has been possible to assess the performance of the package at a high statistical confidence level. The package provides a high level of inlet system cleanliness, a significant reduction in fuel consumption and reduced HC emissions.

Low Temperature Combustion using compression ignition may provide high efficiency combined with low emissions of oxides of nitrogen and soot. This process is facilitated by fuels with lower cetane number than standard diesel fuel. Mixtures of gasoline and diesel (“dieseline”) may be one way of achieving this, but a practical concern is the flammability of the headspace vapours in the vehicle fuel tank. Gasoline is much more volatile than diesel so, at most ambient temperatures, the headspace vapours in the tank are too rich to burn. A gasoline/diesel mixture in a fuel tank therefore can result in a flammable headspace, particularly at cold ambient temperatures. A mathematical model is presented that predicts the flammability of the headspace vapours in a tank containing mixtures of gasoline and diesel fuel. Fourteen hydrocarbons and ethanol represent the volatile components. Heavier components are treated as non-volatile diluents in the liquid phase.

Precise, repeatable and representative testing is a key tool for developing and demonstrating automotive fuel and lubricant products. This paper reports on the first findings of a project that aims to determine the requirements for highly repeatable test methods to measure very small differences in fuel economy and powertrain performance. This will be underpinned by identifying and quantifying the variations inherent to this specific test vehicle, both on-road and on Chassis Dynamometer (CD), that create a barrier to improved testing methods. In this initial work, a comparison was made between on-road driving, the New European Drive Cycle (NEDC) and World harmonized Light-duty Test Cycle (WLTC) cycles to understand the behavior of various vehicle systems along with the discrepancies that can arise owing to the particular conditions of the standard test cycles.

A series of viscous and surface friction modifier additives has been studied in a modified SI engine with separable valve train lubrication. From the results, it has been possible to classify the hydrodynamic or boundary lubrication nature of the observed effects for a series of lubricant additives. It is shown that the frictional benefit of a given additive depends not only on the engine operating condition but also on the engine components on which it is acting. For some additives a fuel economy benefit can switch to a disbenefit as operating regime changes and a different aspect of the additive properties becomes important. Such observations are rationalised in the context of conventional lubrication theory.

Because reformer technology can be used in conjunction with advanced internal combustion engine technology, it is important to be able to formulate fuels that are compatible with both reformers and ICEs It has been found that most hydrocarbon species typically present in gasoline can be reformed with relative ease. The exception is that olefinic species of carbon number 6 and above are relatively much harder to reform. It is shown how a reformer compatible gasoline fuel with high octane can be blended. For Diesel fuels, synthetic ‘Gas to Liquid’ fuels are generally less susceptible to coking and hence superior to petroleum-derived fuels, for use with an onboard reformer.

The Coordinating European Council, CEC, develops performance tests for the motor, oil, petroleum, additive and allied industries. In recent years, CEC has moved away from using round robin programmes (RRP's) for monitoring the precision and severity of test methods in favour of regular referencing within a test monitoring system (TMS). In a TMS, a reference sample of known performance, determined by cross-laboratory testing, is tested at regular intervals at each laboratory. The results are plotted on control charts and determine whether the installation is and continues to be fit to evaluate products. Results from all laboratories are collated and combined to monitor the general health of the test. The TMS approach offers considerable benefits in terms of detecting test problems and improving test quality. However, the effort required in collating data for statistical analysis is much greater, and there are technical difficulties in determining precision from TMS data.

The attributes of a traction fluid are fundamental to the successful operation of a traction drive transmission. The fluid must lubricate and protect the components against wear and corrosion, whilst simultaneously providing high traction to transmit power efficiently. A selection of commercial and candidate fluids have been assessed with both a bench-test and a novel traction rig. The principal objective has been to achieve a balance between the conflicting requirements of low temperature viscometrics and high temperature traction. Fluid performance is found to vary according to the rig employed underlining the need to test under prevailing conditions. Data from the traction rig is validated against a variator module.

Reduction of vehicle exhaust emissions is an important contributor to improved air quality. At the same time demand is growing for new transportation fuels that can enhance security and diversity of energy supply. Gas to Liquids (GTL) Fuel has generated much interest from governments and automotive manufacturers. It is a liquid fuel derived from natural gas, and its properties - sulphur free, low polyaromatics and high cetane number - make it desirable for future clean light-duty diesel engines. In this paper, the effects of distillation characteristics and cetane number of experimental GTL test fuels on direct injection (DI) diesel combustion and exhaust emissions were investigated, together with their spray behaviour and mixing characteristics. The test results show that the lower distillation test fuels produce the largest reductions in smoke and PM emissions even at high cetane numbers. This is linked to the enhanced air/fuel mixing of the lighter fuel in a shorter time.

It is useful for research purposes to define simple surrogate gasoline compositions that can replicate the chemical and physical properties of more complex mixtures. Ethanol is used in commercially available gasolines around the world as part of the pathway to the decarbonization of the transportation sector. In this study equations were developed to predict the Research Octane Number (RON), Motor Octane Number (MON) and Dry Vapour Pressure Equivalent (DVPE) of gasoline surrogates containing ethanol (10-25 vol%), isopentane, n-heptane, isooctane and toluene. The non-linear blending behaviour associated with ethanol is found to necessitate coefficients in the equations developed for MON that are a function of ethanol content, whereas surprisingly the equations for RON and DVPE do not need this added level of complexity.

It is anticipated that worldwide energy demand will approximately double by 2050, whilst at the same time, CO2 emissions need to be halved. Therefore, there is increasing pressure to improve the efficiency of all machines, with great focus on improving the fuel efficiency of passenger cars. The use of downsized, boosted, gasoline engines, can lead to exceptional fuel economy, and on a well-to-wheels basis, can give similar CO2 emissions to electric vehicles (depending, of course, on how the electricity is generated). In this paper, the development of a low weight concept car is reported. The car is equipped with a three-cylinder 0.66 litre gasoline engine, and has achieved over 100 miles per imperial gallon, in real world driving conditions.

Due to the recent drive to reduce CO₂ emissions, the turbocharged direct injection spark ignition (turbo DISI) gasoline engine has become increasingly popular. In addition, future turbo DISI engines could incorporate a form of charge dilution (e.g., lean operation or external EGR) to further increase fuel efficiency. Thus, the conditions experienced by the fuel before and during combustion are and will continue to be different from those experienced in naturally aspirated SI engines. This work investigates the effects of fuel properties on a modern and prototype turbo DISI engine, with particular focus on the octane appetite: How relevant are RON and MON in predicting a fuel's anti-knock performance in these modern/future engines? It is found that fuels with high RON and low MON values perform the best, suggesting the current MON requirements in fuel specifications could actually be detrimental.

In this study, the influence of gasoline composition on exhaust emissions has been evaluated using three gasoline vehicles. Although the vehicles were obtained within Europe, each is representative of models to be found in Asian markets. Two of the vehicles were current Euro 4 certification, while the third was of Euro 2 certification equivalent to that available in specific Asian markets. Fuel effects studied included aromatics, olefins and benzene content. Other fuel properties were held constant within the normal constraints of blending when using realistic gasoline components. An orthogonal matrix of eight fuels was blended to evaluate these properties over the ranges: Aromatics (excluding benzene) 34% to 49%, olefins 18% to 25% and benzene 1% to 5%. All fuels were tested in all three cars driving the current legislative NEDC cycle, using a randomised block design with at least 3 repeats on each fuel/vehicle combination.

The influence of gasoline quality on exhaust emissions has been evaluated using four modern European gasoline cars with advanced features designed to improve fuel economy and CO2 emissions, including stoichiometric direct injection, lean direct injection and MPI with variable valve actuation. Fuel effects studied included sulphur content, evaluated over a range from 4 to 148 mg/kg, and other gasoline properties, including aromatics content, olefins content, volatility and final boiling point (FBP). All four cars achieved very low emissions levels, with some clear differences between the vehicle technologies. Even at these low emissions levels, all four cars showed very little short-term sensitivity to gasoline sulphur content. The measured effects of the other gasoline properties were small and often conflicting, with differing directional responses for different vehicles and emissions.

Shell was the first oil marketer to bring to commercial scale, Gas to Liquids (GTL) technology for fuels and base oils production. This started with the commissioning of the multi-purpose GTL facility at Bintulu, Malaysia in 1993. The plant produces both automotive gas oil (GTL Fuel) as well as a number of speciality products including detergent feedstocks, a range of Fisher-Tropsch commercial wax grades, and a feedstock for base oils production. The base oil feedstock has been shipped to Shell facilities in Japan and France since 1994 where it is solvent de-waxed to produce the first commercially available GTL base oils. The GTL Fuel is currently being used in premium diesels in Germany, Greece and Thailand. Shell has announced in 2003 its intention to build two world scale GTL trains in Qatar and this will include substantial fuels and base oils facilities.

Reduction of exhaust emissions was investigated in a modern diesel engine equipped with advanced diesel after treatment system using a Gas-to-Liquid (GTL) fuel, a cleaner burning alternative diesel fuel. This fuel has near zero sulfur and aromatics and high cetane number. Some specially prepared GTL fuel samples were used to study the effects of GTL fuel distillation characteristics on exhaust emissions before engine modification. Test results indicated that distillation range of GTL fuels has a significant impact on engine out PM. High cetane number also improved HC and CO emissions, while these fuel properties have little effect on NOx emissions. From these results, it was found that low distillation range and high cetane number GTL fuel can provide a favorable potential in NOx/PM emissions trade-off. In order to improve the tail-pipe emissions in the latest diesel engine system, the engine modifications were carried out for the most favorable GTL fuel sample.

Injector nozzle deposits can have a profound effect on particulate emissions from vehicles fitted with Gasoline Direct Injection (GDI) engines. Several recent publications acknowledge the benefits of using Deposit Control Additives (DCA) to maintain or restore injector cleanliness and in turn minimise particulates, but others claim that high levels of DCA could have detrimental effects due to the direct contribution of DCA to particulates, that outweigh the benefits of injector cleanliness. Much of the aforementioned work was conducted in laboratory scenarios with model fuels. In this investigation a fleet of 7 used GDI vehicles were taken from the field to determine the net impact of DCAs on particulates in real-world scenarios. The vehicles tested comprised a range of vehicles from different manufacturers that were certified to Euro 5 and Euro 6 emissions standards.

Fuel with higher octane content is playing a key role in optimising engine performance by allowing a more optimal spark timing which leads to increased engine efficiency and lower CO2 emissions. In a previous study the impact of octane was investigated with a fleet of 20 vehicles using market representative fuels, varying from RON 91 to 100. The resulting data showed a clear performance and acceleration benefit when higher RON fuel was used. In this follow-up study 10 more vehicles were added to the database. The vehicle fleet was extended to be more representative of Asian markets, thus broadening the geographical relevance of the database, as well as adding vehicles with newer technologies such as boosted down-sized direct injection engines, or higher compression ratio engines. Eight different fuel combinations varying in RON were tested, representing standard gasoline and premium gasoline in different markets around the world.

Lubricant samples were aged on a SI bench engine that was run using ten different gasoline fuels. For each gasoline tested, the oxidative stability of the lubricant and the extent of engine wear was assessed in terms of a number of different parameters. Surprisingly, it was found that fuels containing higher levels of olefin (whether C8 olefin, or a C5/C6 olefin blend, or a catalytically cracked refinery stream) performed directionally better than a reference gasoline with low levels of aromatics and olefins. Fuels with a higher final boiling point and higher aromatic content, appeared to be associated with enhanced levels of sludge formation than the reference gasoline, but did not give rise to enhanced engine wear.

Laminar burning velocity is a fundamental combustion property of any fuel/air mixture. Formulating gasoline fuel blends having faster burning velocities can be an effective strategy for enhancing engine and vehicle performance. Formulation of faster burning fuels by changing the fuel composition has been explored in this work leading to a clear correlation between engine performance and fuel burning velocity. In principle a gasoline vehicle should be calibrated to give optimal ignition timing (also known as MBT - minimum spark advance for best torque) while at the same time avoiding any possible engine knock. However, modern downsized/boosted engines frequently tend to be limited by knock and the spark timing is retarded in respect of the optimum. In such scenarios, faster burning fuels can lead to a more optimum combustion phasing resulting in a more efficient energy transfer and hence a faster acceleration and better performance.

Worldwide, Fuel Economy (FE) legislation increasingly influences vehicle and engine design, and drives friction reduction. The link between lubricant formulation and mechanical friction is complex and depends on engine component design and test cycle. This Motored Friction Tear Down (MFTD) study characterizes the friction within a 3.6L V6 engine under operating conditions and lubricant choices relevant to the legislated FE cycles. The high-fidelity MFTD results presented indicate that the engine is a low-friction engine tolerant of low viscosity oils. Experiments spanned four groups of engine hardware (reciprocating, crankshaft, valvetrain, oil pump), five lubricants (four candidates referenced against an SAE 0W-20) and five temperature regimes. The candidate lubricants explored the impact of base oil viscosity, viscosity modifier (VM) and friction modifier (FM) content.