Search Results

This paper addresses challenges in current Fuel Cell Stack Buses and presents a novel Fuel Cell Electric Vehicle Bus (FCEV-Bus) powertrain that combines fuel cells, ultra-capacitors, and batteries to enhance performance and reliability. Existing Fuel Cell Stack Buses struggle with responsiveness, power fluctuations, and cost-efficiency. The FCEV-Bus powertrain uses a Fuel Cell stack as the primary power source, ultra-capacitors for quick power response, and batteries for addressing power variations. Batteries also save costs in certain cases. This combination optimizes power management, improves system efficiency, and extends the FCEV-Bus's operational life. In conclusion, this paper offers an innovative solution to overcome traditional fuel cell system limitations, making FCEV-Buses more efficient and reliable for potential wider adoption.

DFSS is a disciplined problem prevention approach which helps in achieving the most optimum design solution and provides improved and cost effective quality products. This paper presents the implementation of DFSS method to design a distinctive cooling system where engine is mounted in the rear and radiator is mounted in the front of the car. In automobile design, a rear-engine design layout places the engine at the rear of the vehicle. This layout is mainly found in small, entry level cars and light commercial vehicles chosen for three reasons - packaging, traction, and ease of manufacturing. In conventional Passenger cars, a radiator is located close to the engine for simple packaging and efficient thermal management. This paper is about designing a distinctive cooling system of a car having rear mounted engine and front mounted radiator.

Authors were challenged with a task of developing a full vehicle simulation model, with a target to simulate the electrical system performance and perform digital tests like Battery Charge Balance, in addition to the fuel efficiency estimation. A vehicle is a complicated problem or domain to model, due to the complexities of subsystems. Even more difficult task is to have a control algorithm which controls the vehicle model with the required control signals to follow the test specification. Particularly, simulating the control of a vehicle with a manual transmission is complicated due to many associated control signals (Throttle, Brake and Clutch) and interruptions like gear changes. In this paper, the development of a full vehicle model aimed at the assessment of electrical system performance of the vehicle is discussed in brief.

Reduction of NOx (Oxides of Nitrogen) and particulates from engine exhaust is one of the prime considerations in current research and development in automotive industry. The present paper describes the combustion optimization done on a four cylinder, 4 liter DI diesel engine to meet stringent Euro-III emission norms. The engine FIE (Fuel Injection Equipment) and injector geometry was optimized for performance and emission. Smoke measurements were considered as indicative of soot, to predict particulate emissions. This was done to simplify the overall process and save development time. It was concluded that by combining the flexibility of electronically controlled fuel injection begin, with improved nozzle technologies, with higher spray velocities and spray penetration, a considerable reduction in NOx and particulate emissions can be achieved. This can serve as a low cost solution, without any exhaust after-treatment systems.

Micro Hybrid Systems are a premier approach for improving fuel efficiency and reducing emissions, by improving the efficiency of electrical energy generation, storage, distribution and consumption, yet with lower costs associated with development and implementation. However, significant efforts are required while implementing micro hybrid systems, arising out of components like Intelligent Battery Sensor (IBS). IBS provides battery measurements and battery status, and in addition mission critical diagnostic data on a communication line to micro hybrid controller. However, this set of data from IBS is not available instantly after its initialization, as it enters into a lengthy learning phase, where it learns the battery parameters, before it gives the required data on the communication line. This learning period spans from 3 to 8 hours, until the IBS is fully functional and is capable of supporting the system functionalities.

Customer preference towards quieter vehicles is ever-increasing. Exhaust tailpipe noise is one of the major contributors to in-cab noise and pass-by-noise of the vehicle. This research proposes a silencer with an integrated acoustic valve to reduce exhaust tailpipe noise. Incident exhaust wave coming from the engine strikes the acoustic valve and generates reflected waves. Incident waves and reflected waves cancel out each other which results in energy loss of the exhaust gas. This loss of energy results in reduced noise at the exhaust tailpipe end. To evaluate the effectiveness of the proposed silencer on the vehicle, NVH (Noise, vibration, and harshness) performance of the proposed silencer was compared with the existing silencer which is without an acoustic valve. A CNG (Compressed natural gas) Bus powered by a six-in-line cylinder engine was chosen for the NVH testing.

Now a day’s automated manual transmissions (AMT) are getting popular because of hassle-free gear shifting and improved fuel economy. OEMs are converting their existing manual gearbox to AMT gearbox with solution like hydraulic or electric AMT kit that replaces the manual shift mechanism to automated actuators. Generally, in manual gearbox, the operational principal of reverse gear is sliding mesh. Due to sliding mesh gear arrangement, it can create interruption for gearshift while controlling shift actuators. In this paper, reverse gear shift arrangement and its operational dynamics at different operating condition has been studied and analyzed in detail. Based on status of vehicle, to ease the gearshift, engagement flow process proposed. The control methods that increases probability of smooth and easier shifting in all operating condition discussed in detail. The developed control algorithm discussed along with its implementation on real vehicle and results.

Engine Stop/Start System (ESS) promises to reduce greenhouse emissions and improve fuel economy of vehicles. Previous work of the Authors was concentrated on bridging the gap of improvement in fuel economy promised by ESS under standard laboratory conditions and actual driving conditions. Findings from the practical studies lead to a conclusion that ESS is not so popular among the customers, due to the complexities of the system operation and poor integration of the system design with the driver behavior. In addition, due to various functional safety requirements, and traffic conditions, actual benefits of ESS are reduced. A modified control algorithm was proposed and proven for the local driving conditions in India. The ways in which a given driver behaves on the controls of the vehicles like Clutch and Brake Pedals, Gear Shift Lever were not uniform across the demography of study and varied significantly.

With the current state of ever rising fuel prices and unavailability of affordable alternate technologies, significant research and development efforts have been invested in recent times towards improving fuel efficiency of vehicles powered with conventional internal combustion engines. To achieve this, a varied approach has been adopted by researchers to cover the entire energy chain including fuel quality, combustion quality, power generation efficiency, down-sizing, power consumption efficiency, etc. Apart from energy generation, distribution and consumption, another domain that has been subjected to significant scrutiny is energy recuperation or recovery. A moving vehicle and a running engine provide a number of opportunities for useful back-recovery and storage of energy. The most significant sources for recuperation are the kinetic energy of the moving vehicle or running engine and to a lesser extent the thermal energy from medium such as exhaust gas.

When an automobile negotiates a flooded region, water is splashed due to the rotational motion of the wheels. This water enters the air intake system of the turbocharged intercooled engine along with air and can pass through the turbocharger, intercooler and enter the engine. As water is an incompressible fluid, the piston cannot compress water inside the cylinder which leads to connecting rod bending and severe engine damage. This paper explains how the same has been resolved using CFD methodology and proposes the re-designed model of mud cover as a solution to this problem. The entire process has been streamlined and major time and cost reduction achieved by using simulation for optimization. The simulated results have been validated by extensive trials for correlation and outdoor tests for durability. Same analysis technique is used as a template to modify the air intake system.

Key on/off (KOKO) Vibration plays a vital role in the quality of NVH (Noise Vibration and Harshness) on a vehicle. A good KOKO experience on the vehicle is desirable for every customer. The vibration transfer to the vehicle can be refined either by reducing the source vibrations or improving isolation efficiency. For the engine mounting system of passenger cars, the mounts are an isolating element between the powertrain and receiver. Various noise, Vibration, and harshness criteria must be fulfilled by mounting system performance like driver seat rail vibration (DSR), tip-in/tip-out, judder performance, DSR at idle and Key on/off Vibration. Out of these requirements, in the paper, the investigation is done on KOKO improvement without affecting other NVH parameters related to mount performance. Higher damping is required to isolate Vibration generated during the Key-on event, and lower damping is required during the idle condition of the vehicle.

Better ride and comfort, enhanced safety, reliability and durability, lower running cost as well as cost of ownership continue to be challenges for automotive OEMs. Higher fuel efficiency is considered as USP not only for lower running cost but also is hygiene factor from sustainability point of view. This has necessitated the need for Augmenting Light weighting horizon in automotive OEMs. Augmenting this leads to invention of innovative materials and processes for emerging cost competitive market. This paper focuses on technology efforts towards augmenting light weighting Horizon in Automotive. Light weighting concepts being explored by OEMs with the help of automotive component manufacturers from Powertrain - Engines & Transmission, Chassis and Suspension are discussed.

This paper introduces a novel approach to automate PID calibration for closed-loop control systems and the creep control function in an electric vehicle. Through a comprehensive literature survey, it is found that this method is the first of its kind to be applied in the field of automated electric vehicle calibration for Creep function. The proposed approach utilizes a systematic methodology that automatically tunes the PID parameters based on predefined performance criteria, including energy consumption and jerk. To implement this methodology, the ETAS INCA FLOW software, which provides guided calibration methods for in-vehicle testing & calibration, is employed. The calibration process is performed on a real-time electric vehicle platform to validate the effectiveness of the proposed approach. The results of this study showcases the advantages of automated PID calibration for closed-loop control systems and creep control function in small commercial electric vehicle.

Vehicle incab booming perception, a low frequency response of the structure to the various excitations presents a challenging task for the NVH engineers. The excitation to the structure causing boom can either be power train induced, depending upon the number of cylinders or the road inputs, while transfer paths for the excitation is mainly through the power train mounts or the suspension attachments to the body. The body responds to those input excitations by virtue of the dynamic behavior mainly governed by its modal characteristics. This paper explains in detail an integrated approach, of both experimental and numerical techniques devised to investigate the mechanism for boom noise generation. It is therefore important, to understand the modal behavior of the structure. The modal characteristics from the structural modal test enable to locate the natural frequencies and mode shapes of the body, which are likely to get excited due to the operating excitations.

Climate change due to global warming calls for more fuel-efficient technologies. Parallel Full hybrids are one of the promising technologies to curb the climate change by reducing CO2 emissions significantly. Different parallel hybrid electric vehicle (HEV) architectures such as P0, P1, P2, P3 and P4 are adopted based on different parameters like fuel economy, drivability, performance, packaging, comfort and total cost of ownership of the vehicle. It is a great challenge to select right hybrid architecture for different vehicle segments. This paper compares P2 and P3 HEV with AMT transmission to evaluate most optimized architecture based on vehicle segment. Vehicles selected for study are from popular vehicle segments in India with AMT transmission i.e. Entry segment hatch and Compact SUV. HEV P2 and P3 architectures are simulated and studied with different vehicle segments for fuel economy, performance, drivability and TCO.

Use of adhesives in automotive require in-depth material, design, manufacturing & engineering knowledge. It is also necessary to understand functional requirements. For perfect and flawless adhesive joinery, the exact quantity of adhesive, its material composition, thickness of adhesive layer, substrate preparation methods for adhesive bonding, handling and curing time of the adhesive have to be studied & optimized. This paper attempts to describe different aspects of adhesive bonding in automotive industry to include: Selection of adhesives based on application and design of the components, surface preparation of adherend, designing of adhesive joint, curing conditions of adhesives, testing and validation of adhesive joints. Emphasis was given to study & verify the performance of different adhesive joints to meet end product requirements. Samples were prepared with a variety of adhesive and adherend combinations.

CNG fuel has recently gained popularity in passenger and commercial vehicles due to its lower cost of operation compared to gasoline and diesel. It is also a more environmentally friendly fuel than other fuels. Converting a customer vehicle with a Diesel option to a CNG option is more difficult than building a new CNG vehicle. In this we are outlining the design of CNG fuel systems and the challenges of replacing them during the transition from Diesel to CNG and qualifying the Government Norms for running the vehicle will increase the life as well as make our environment more eco-friendly than diesel vehicles.

IC (Internal Combustion) engines are evolved and refined over time to greater levels of technology in terms of emission, performance, NVH (Noise, Vibration & Harshness), and design philosophy. Crank-train generates a greater impact on NVH optimization due to its geometry and dynamics. Hence, more attention to mass balancing is required to minimize the negative impact on NVH. The present work demonstrates the evaluation of balancing rate of crank-train system from the first principle of couple balancing. Calculations are conducted at the concept stage to estimate an internal rotating couple balancing of crank-train system due to counterweights and rotating masses. As crankshaft weighs approximately 10-12% weight of an engine and its counter weight plays a vital role in balancing, its optimization will result in a significant impact on NVH.

The goal of reducing fuel consumption and CO2-Emission is leading to turbo-charged combustion engines that deliver high torque at low speeds (down speeding). To meet NVH requirements damper technologies such as DMF (Dual Mass Flywheel) are established, leading to reduced space for the clutch system. Specific measures need to be considered if switching over from SMF (Single Mass Flywheel) to DMF [8]. Doing so has an impact on thermal behavior of the clutch system, for example due to reduced and different distribution of thermal masses and heat transfer to the surroundings. Taking these trends into account, clutch systems within vehicle powertrains are facing challenges to meet requirements e.g. clutch life, cost targets and space limitation. The clutch development process must also ensure delivery of a clutch system that meets requirements taking boundary conditions such as load cycles and driver behavior into account.

This paper deals with the problem of cyclic irregularities during idling in relation with port to port fuel delivery variation of rotary Fuel Injection Pump (FIP) for a diesel engine. The relation is demonstrated on a two cylinder engine, where problem of high cyclic irregularities was observed for which the root cause was identified as the fuel delivery variation from the FIP, which was later taken up for the improvements in the design. This paper discusses the technical approach used in identifying the root cause for the high cyclic irregularities and the solution of the problem. It is demonstrated how angular acceleration of the crankshaft free end can be used to diagnose the non-uniformity of combustion in different cylinders which leads to higher cyclic irregularities. The solution discusses the improvements done in the hydraulic passages of the head and rotor of the FIP for line to line fuel delivery variation control.