Search Results

Non-equilibrium all-atom MD simulations are used to study the traction properties of hydrocarbon fluids. A fluid layer is confined between two solid Fe plates under the constant normal force of 1.0 GPa. Traction simulations are performed by applying a relative sliding motion to the Fe plates. Shear behaviors of nine hydrocarbon fluids are simulated on a sufficiently large film thickness of 6.7 nm, and succeeded in reproducing the order of the experimental traction coefficients. The dynamic mechanism of the momentum transfer on layers of fluid molecules are analyzed focusing on the intermolecular interactions (density profile, orientation factor, pair-correlation function) and intramolecular interactions (intramolecular interaction energy, conformation change of alicyclic ring). In contrast to the case of n-hexane, which shows low traction due to a fragile chain-like interaction, other mechanisms are obtained in the high traction molecules of cyclohexane, dicyclohexyl and santotrac 50.

If a vehicle is left in a humid environment, the coefficient of friction between the brake pads and discs increases, generating a discomforting noise during braking called brake squeal. It is assumed that this increase in the coefficient of friction in a humid environment is the effect of moisture penetrating between the brake friction surfaces. Therefore, this paper analyzes the factors causing coefficient of friction variation with moisture between the friction surfaces by dynamic observation of these surfaces. The observation was achieved by changing the disc materials from cast iron to borosilicate glass. One side of the glass brake disc was pushed onto the brake pad and the sliding surface was observed from the opposite side by a charge coupled device (CCD) camera. First, a preliminary test was carried out in a dry state using two pad materials with different wear properties to select the appropriate pad for observing the friction surfaces.

With the goal of improving drivability, this research aimed to clarify the mechanism of vehicle longitudinal acceleration, focusing on tip-in acceleration. Conventional typical analysis methods include experimental modal and model-based analysis. However, since the former requires the measurement of impulses and other input forces while the vehicle is stopped, measurement under actual driving conditions is difficult. The latter requires characteristic values such as the stiffness and damping coefficients to be identified in advance, which cannot be achieved either easily or precisely. Therefore, this paper proposes a new experiment-based analysis method. This method enables the acquisition of engine torque and transmission torque/force by measuring only the acceleration values of some components under driving conditions.

This paper deals with a case where H∞ control is applied to a basic control logic of a rack-assisted Electric Power Steering (EPS) system. In the body, the following three key features are described: Construction of the target controlled model including a vehicle Controller design for the model H∞ controller performance verification In this paper, it has been confirmed that H∞ control is valid as a basic control logic for the EPS system.

A technique has been developed that uses unsteady flow simulation to evaluate mirror vibration quantitatively at the drawing stage. Studies made in actual driving tests of the contributions of different inputs to mirror vibration have confirmed that the contribution of fluid force is large, so a visualization of the structure of the external rearview mirror wake was done using PIV. The results made it clear that the vibration imparted to the mirror surface by air flow excites the natural vibration mode of the mirror surface, thereby causing the mirror to vibrate. Mirror vibration performance was evaluated by means of unsteady flow simulation using the moment PSD as a substitute characteristic. (The moment PSD was obtained by a frequency analysis of the changes over time in the moment generated in the mirror surface by the fluid force.) The results obtained through CFD show a high degree of correlation with those obtained in actual driving tests.

We have proposed First Order Analysis (FOA) as a method, which the engineering designers themselves can use easily in an initial design stage. In this paper, we focus on the crashworthiness, and present the method to predict the collapse behavior of the frame member. This method is divided into two parts. Those are (1) collapse analysis under loading conditions of combined axial force and bending moment to the cantilever, and (2) collapse analysis of structural member considering the previously obtained moment - rotation angle relationship using the beam element. In comparison with the results according to the detailed Finite Element Analysis (FEA) model, effectiveness and validity of this method are presented.

A new experimental apparatus to visualize and measure the flow in the stator of a torque converter is proposed. A one-sided coaxial shaft constructed of an input shaft and an output shaft provides an open space inside the stator shaft for measurement. Through the window on the stator shaft, the flow in the stator can be directly observed. We also improved the laser sheet lighting method into the blade passage by using a mirror inside the blade. By visualizing the flow with the laser sheet lighting method, we found that the flow around the leading edge has different separation regions along the blade span. Furthermore, by using a laser doppler velocimeter, velocity vectors and turbulence intensities were measured in three stator blades of different thicknesses with the same camber line. The thickness of the stator blades affects the flow patterns.

The laser-induced exciplex fluorescence (LIEF) technique, currently used to observe mixture formation in a diesel engine, has been applied to a spark ignition (SI) engine and a new equivalence ratio calibration technique has been developed in order that two-dimensional measurements of the equivalence ratio may be made in an operating engine. Spectrally separated fluorescent images of liquid and vapor phase fuel distributions were obtained by adding new exciplex-forming dopants to the gasoline fuel. Dual light sheets from an excimer laser were introduced into one of the cylinders of a 4-valve lean-burn engine, and 2-D images of the mixture formation were recorded at pre-set crank angles during the induction and compression strokes by an image-intensified camera equipped with the appropriate filter.

Quality control of gasoline constituents and its effect on the Intake Valve Deposits (IVD) has become a recent issue. In this paper, the effects of gasoline and oil quality on intake valve deposits were investigated using an Intake Valve Deposit Test Bench and a Sludge Simulator. The deposit formation from the gasoline maximized at an intake valve temperature of approximately 160 °C, and the deposits formed from the engine oil were maximum at approximately 250 °C. Therefore, the contribution of the gasoline or the engine oil appears to depend on the engine conditions. The gasoline which contains MTBE or ethanol with no detergent additive slightly increases the deposition amount. The gasoline with a superior detergent significantly decreases the deposition amount even when MTBE or ethanol is blended in the gasoline. Appropriate detergent fuel additive retards the oil deterioration.

The drag reduction mechanism in newly developed low aerodynamic drag model car is investigated through numerical simulation. In order to deal with the computational domain around a three-dimensional complicated vehicle body, the method of overlaid grid system is employed. The results of computational case study on the body shape demonstrate that the lateral tapering near the rear end and the spats around the wheels bring better flow properties for drag reduction, such as the pressure recovery in the wake.

This study models short circuits and blow-outs of spark channels. The short circuit model assumes that a spark channel is short-circuited between two arbitrary locations when the electric potential difference between the two locations exceeds the voltage which enables electrical insulation breakage in-between. The threshold voltage can be raised by increasing the distance between the two locations and decreasing the discharge current. Discharge current, in this model, represents the influence of both the spread and the number of electrically charged particles, i.e., electrons and positive ions, distributed near the two locations. Meanwhile, the blow-out model assumes that a strong flow diffuses electrons and positive ions in the spark channel, and consequently the discharge blows out.

In this paper, we will introduce a stereo vision system developed as a sensor for a vehicle's front monitor. This system consists of three parts; namely, a stereo camera that collects video images of the forward view of the vehicle, a stereo ECU that processes its output image, and a near-infrared floodlight for illuminating the front at night. We were able to develop an obstacle detection function for the Pre-Crash Safety System and also a traffic lane detection function for a Lane-Keeping Assist System. Especially in regard to the obstacle detection function, we were able to achieve real-time processing of the disparity image calculations that had formerly required long processing times by using two types of recently developed LSIs.

The stratification feature of DI gasoline combustion was studied by using a constant volume combustion vessel. An index of stratification degree, defined as volumetric burning velocity, has been proposed based on the thermodynamic analysis of the indicated pressure data. The burning feature analysis using this stratification degree and the fuel vapor concentration measurement using He-Ne laser ray absorption method were carried out for the swirl nozzle spray with 90° cone angle and the slit nozzle spray with 60° fan angle. Ambient pressure and ambient temperature were changed from atmospheric condition to 0.5∼0.6 MPa and 465 K, respectively. Air Swirl with swirl ratio of 0∼1.0 were added for the 90° swirl nozzle spray. Single component fuels with different volatility and self-ignitability from each other were used besides gasoline fuel. The major findings are as follows. High ambient temperature improves stratification degree due to the enhanced fuel vaporization and vapor diffusion.

The finite element method (FEM) is effective for analyzing brake squeal phenomena. Although FEM analysis can be used to easily obtain squeal frequencies and complex vibration modes, it is difficult to identify how to modify brake structure design or contact conditions between components. Therefore, this study deals with a practical design method using sensitivity analysis to reduce brake squeal, which is capable of optimizing both the structure of components and contact conditions. A series of analysis processes that consist of modal reduction, complex eigenvalue analysis, sensitivity analysis and optimization analysis is shown and some application results are described using disk brake systems.

In recent years, problems such as global warming, the depletion of natural resources, and air pollution caused by emissions are emerging on a global scale. These problems call for efforts directed toward the development of fuel-efficient engines and exhaust gas reduction measures. As a solution to these issues, performance improvements should be achieved on the oil that lubricates the sliding sections of engines. This report points to features required of future engine oil-such as contribution to fuel consumption, minimized adverse effects on the exhaust gas aftertreatment system, and improved reliability achieved by sludge reduction-and discusses the significance of these features. For engine oil to contribution of engine oil to lower fuel consumption, we examined the effects of reduced oil viscosity on friction using gasoline and diesel engines.

Recently, there has been many practical applications of fuzzy control. Applications of fuzzy control to vehicles are more effective. However, they require more input and output channels as well as higher speed inference ability than typical applications require. We have developed a tool for developing a fuzzy control system available on a vehicle. The tool consists of a fuzzy inference board and a laptop personal computer with a color display executing a user interface software. The fuzzy inference board can be directly connected with an electronic control unit for vehicle control, and has 10 input channels, 5 output channels and 256 rules. The user interface software mainly provides two functions: 1) The screen editor for membership functions and rules. 2) The real-time monitor for input, output, and grade values when fuzzy inference is executed.

Estimating distant road structure will be an important factor in determining the extent of danger of detected obstacles. There are some methods to estimate the road structure by an image from an onboard camera. However, the results are not sufficient due to the vertical curvature of roads and the limitation of image resolution. In this paper, a new method is proposed to estimate the 3-D road structure by fusion of a 2-D digital road map and an image from a camera. The effect of this method is confirmed by using synthesized data and actual data.

Grip feeling is an important facet in vehicle dynamics evaluation from a driver satisfaction and enjoyment standpoint. To improve grip feeling, we analyzed the subjective comments from test driver's about grip feeling and an evaluated human sensitivity to lateral motion. As a result, we found that drivers evaluate transient grip feeling according to the magnitude of lateral jerk. Next, we analyzed what vehicle parameters affect lateral jerk by using theoretical equations. As a result, we found that cornering power is an important parameter, especially the cornering power of rear tires as they can be create larger lateral jerk than can front tires.