Search Results

As part of the International Lubricant Standardization and Approval Committee's (ILSAC) goal of developing a global automatic transmission fluid (ATF) specification, members have been evaluating test methods that are currently used by various automotive manufacturers for qualifying ATF for use in their respective transmissions. This report deals with comparing test methods used for determining torque capacity in friction systems (shifting clutches). Three test methods were compared, the Plate Friction Test from the General Motors DEXRON®-III Specification, the Friction Durability Test from the Ford MERCON® Specification, and the Japanese Automotive Manufacturers Association Friction Test - JASO Method 348-95. Eight different fluids were evaluated. Friction parameters used in the comparison were breakaway friction, dynamic friction torque at midpoint and the end of engagement, and the ratio of end torque to midpoint torque.

Our two types of NOx storage-reduction (NSR) catalyst have been tested under various conditions of thermal endurance; the performance of these catalysts have been regressed to give the formulas that enable to estimate the performance after thermal endurance; and we have found the method to simplify (shorten the duration of) the thermal endurance tests and that the thermal deterioration of NSR catalysts is controlled by the worst condition of endurance (at least approximately). The regression formula for the amount of potassium that contributes to the catalyst performance (active K) after the endurance has also been obtained. These formulas predict that the amount of active K is the least for the worst condition of endurance and suggest a difference in deterioration mechanism that reflects the performance between low and high temperatures and the portion of worse deterioration (front or rear).

NO2 sources of roadside atmosphere at Matsubarabashi monitoring station in Tokyo were investigated analytically. The result showed that contribution of urban background is dominant from November to February and NO oxidation with O3 has large contribution from April to September. NO2 air quality standard will be achieved by reducing vehicle NOx emission to post-new long-term regulation level. The analytical method was verified by using our developed simulation system, which consists of micro traffic flow analyzer and CFD-based, unsteady-state diffusion with chemical reaction solver.

The dissolution and exfoliation of chromium plating specific to Russia was studied. Investigation and analysis of organic compounds in Russian soil revealed contents of highly concentrated fulvic acid. Additionally, it was found that fulvic acid, together with CaCl2 (a deicing agent), causes chromium plating corrosion. The fulvic acid generates a compound that prevents reformation of a passivation film and deteriorates the sacrificial corrosion effectiveness of nickel.

Rubber is a thermosetting material and as such is generally considered difficult to recycle; therefore there is a demand for the development of rubber recycling technology to protect the environment and conserve resources. Some technologies exist to recycle vulcanized rubber, but none of these has high enough productivity to produce reclaimed rubber, and re-vulcanized rubber does not have the same properties as virgin rubber materials. Now a new recycling technology, called Shear Flow Stage Reactor, has been developed for rubber reclamation. This new technology has high productivity and can achieve the same properties as virgin materials. Automotive parts have been developed and are being produced with recycled Ethylene-Propylene-diene Rubber (EPDM) based on this new technology. The performance of the developed parts is the same as the parts made from virgin materials.

This paper describes the development of a fracture finite element (FE) model for laser screw welding (LSW) and validation of the model with experimental results. LSW was developed and introduced to production vehicles by Toyota Motor Corporation in 2013. LSW offers superb advantages such as increased productivity and short pitch welding. Although the authors had previously developed fracture FE models for conventional resistance spot welding (RSW), a fracture model for LSW has not been developed. To develop this fracture model, many comprehensive experiments were conducted. The results revealed that LSW had twice as many variations in fracture modes compared to RSW. Moreover, fracture mode bifurcations were also found to result from differences in clearance between welded plates. In order to analyze LSW fracture phenomena, detailed FE models using fine hexahedral elements were developed.

A hardening depth evaluation technique using eddy current has been developed, which can be applied to a mass production line for destructive (cutting) inspections. Using this technique, changes in the hardness of the induction-hardened structure can be detected based on the changes in magnetic permeability. This technique reduces the thermal effect and improves measurement accuracy through a multi-frequency exciting method and a difference method algorithm.

One primary result of the reduction of platinum group metals (PGM) within a catalytic converter is the decline in NOx conversion efficiency. This paper hypothesizes that the primary factor of this decline to be hydrocarbon (HC) poisoning. To maintain high NOx conversion efficiency as the PGM reduces, Rh activation improvement becomes significant to overcome the HC poisoning. Analysis of the Rh deterioration mechanism found that it is effective to separately arrange Rh and CeO2 on the converter, avoiding the Rh deactivation. By this improvement, we improved the catalyst activity at less than 25% of the original Rh loading.

To improve the thermal efficiency of an internal combustion engine, the application of ceramics to heat loss reduction in the cylinders has been studied [1-2]. The approach taken has focused on the low heat conductivity and high heat resistance of the ceramic. However, since the heat capacity of the ceramic is so large, there is a problem in that the wall temperature increases during the combustion cycle. This leads to a decrease in the charging efficiency, as well as knocking in gasoline engines. To overcome these problems, the application of thermal insulation without raising the gas temperature during the intake stroke has been proposed [3-4]. As a means of achieving this, we developed a "temperature swing heat insulation coating" [5, 6, 7, 8, 9]. This reduces the heat flux from the combustion chamber into the cooling water by making the wall temperature follow the gas temperature as much as possible during the expansion and exhaust strokes.

A low sulfated ash (S.Ash) DL-1/C2 0W-30 diesel engine oil with improved fuel economy has been developed to meet the PM targets outlined in the Euro 5 emissions standards and to help achieve the voluntary European CO2 target of 140 g/km. The newly developed engine oil is an effective solution to the trilemma (triple probrem) of reliability (high detergency and high anti wear), low S.Ash, and fuel economy, achieving a fuel economy improvement of 2% and reducing CO2 emissions by 3 g/km.

A molded headliner made from polypropylene, which we developed for the first time in the world, was adopted in May 1987 for TOYOTA COROLLA. The new material with high stiffness and light weights, has a sandwich structure consisting of PP-sheets and a PP-foam sheet. We have thus succeeded in the production of the new headliner in which each layer is laminated without any adhesive. A unique resin used for PP-sheets as surface skins was developed with high impact, thermal and fire resistances. Further, a PP-form core sheet with soft-feel and good moldability was also developed. As a result, we established proper conditions of molding this material and succeeded in producing stable superior parts with high quality and short cycle-time. Finally new molded headliner is comparable to the suspended type headliner in respect to weight and production cost.

Toyota Motor Corporation has developed the new compact-class hybrid vehicle (HV). This vehicle incorporates a new hybrid system for the improvement of fuel efficiency. For this system, a new Power Control Unit (PCU) is developed. The feature of the PCU is downsizing, lightweight, and high efficiency. In expectation of rapid popularization of HV, the aptitude for mass production is also improved. The PCU, which plays an important role in the new system, is our main focus in this paper. Its development is described.

In order to improve the fuel efficiency of Hybrid Electric Vehicles (HEVs), it is necessary to reduce the size and power loss of the HEV Power Control Units (PCUs). The loss of power devices (IGBTs and FWDs) used in a PCU accounts for approximately 20% of electric power loss of an HEV. Therefore, it is important to reduce the power loss while size reduction of the power devices. In order to achieve the newly developed PCU target for compact-size vehicles, the development targets for the power device were to achieve low power loss equivalent to its previous generation while size reduction by 25%. The size reduction was achieved by developing a new RC-IGBT (Reverse Conducting IGBT) with an IGBT and a FWD integration. As for the power loss aggravation, which was a major issue due to this integration, we optimized some important parameters like the IGBT and FWD surface layout and backside FWD pattern.

The glass-integrated Curved Seal Extrusion (hereafter called “CSE”) is a new technology for manufacturing automobile-window mole. This technology is to extrude and stick mole directly on 3-D shaped window-glass by using the combination of a multi-axes robot and an extruding machine. This process could not be realized through the previous robot technology whose primary purpose was transporting goods, which did not necessitate real-time speed control. This time, we adopted a robot for the purpose of processing plasticity molding. For the purpose of improving formability, productivity, and appearance quality, we optimized the robot's movements and devised a method to vary the molding speed of the extruding machine. Furthermore, we have established a mass production technology by developing the optimum robot control method.

1 The principal characteristics required of sealing materials used in the body shop have focused on their adhesion to oily steel sheets and quick curing performance. Means for attaining these characteristics have been narrowed down to a basic resin system and a curing system. Various techniques have been studied to ensure proper anti-corrosion performance at the sealer application boundaries and thin application areas. They include the addition of anti-corrosion fillers, the provision of conductivity (through electro-deposition), and the application of a micro foam film over the application boundaries. Thus, prospects for attaining the same level of anti-corrosion performance as existing materials have been achieved.

This paper describes the development of a simplified fracture finite element (FE) model for resistance spot welds (RSW) of ultra-high-strength steel (UHSS) that can be incorporated into large-scale vehicle FE model. It is known that the RSW of UHSS generates two types of fracture modes: heat-affected zone (HAZ) and nugget zone fractures. Lap shear and peeling coupon tests using UHSS sheets found that the different RSW fracture modes occurred at different nugget diameters. To analyze this phenomenon, detailed simulated coupon tests were carried out using solid hexahedral elements. The analytical results revealed that RSW fractures are defined by both the application of plastic strain on the elements and the stress triaxiality state of the elements. A detailed model incorporating a new fracture criteria model recreated the different UHSS RSW fracture modes and achieved a close correlation with the coupon test results.

Application of SiC power devices is regarded as a promising means of reducing the power loss of power modules mounted in power control units. Due to those high thermostable characteristics, the power module with SiC power devices are required to have higher operating temperature than the conventional power module with Si power devices. However, the limitations of current packaging technology prevent the utilization of the full potential of SiC power devices. To resolve these issues, the development of device bonding technology is very important. Although transient liquid phase (TLP) bonding is a promising technology for enabling high temperature operation because its bonding layer has a high melting point, the characteristics of the TLP bonding layer tend to damage the power devices. This paper describes the development of a bonding technology to achieve high temperature operation using a stress reduction effect.

Further fuel economy improvement of the internal combustion engine is indispensable for CO2 reduction in order to cope with serious global environmental problems. Although lowering the viscosity of engine oil is an effective way to improve fuel economy, it may reduce the wear resistance. Therefore, it is important to achieve both improved fuel economy and reliability. We have developed new 0W- 8 engine oil of ultra-low viscosity and achieved an improvement in fuel economy by 0.8% compared to the commercial 0W-16 engine oil. For this new oil, we reduced the friction coefficient under boundary lubrication regime by applying an oil film former and calcium borate detergent. The film former increased the oil film thickness without increasing the oil viscosity. The calcium borate detergent enhanced the friction reduction effect of molybdenum dithiocarbamate (MoDTC).

Since bumper reinforcements are positioned at front/rear ends of vehicles, weight reduction of the bumper reinforcements enhances vehicle dynamic performance by reducing a yaw moment of inertia. CFRP (Carbon Fiber Reinforced Plastic) composites are attractive lightweight materials due to their excellent specific strength and rigidity. However, because of their relatively high cost, applications of CFRP materials to vehicle structural parts are limited. In this study we have developed a lightweight, structural part, which consists of a thin-walled Al (Aluminum) bumper reinforcement with a UD (Unidirectional)-CFRP sheet. The intention is to prevent an increased part cost by reducing the amount of Al and by minimizing the amount of CFRP. Compared to Al, UD-CFRP sheets have even higher tensile strength and modulus. When vehicles crash, bumper reinforcements may be subjected to bending force.

In order to reduce the energy consumption of the automotive air conditioning system, adsorption heat pump (AHP) system is one of the key technologies. We have been developing compact AHP system utilizing the exhaust heat from the engine coolant system (80-100 °C), which can meet the requirements in the automotive application. However, AHP systems have not been practically used in automotive applications because of its low volumetric power density of the adsorber. The volumetric power density of the adsorber is proportional to sorption rate, packing density and latent heat. In general, the sorption rate is determined by mass transfer resistance in primary particle of an adsorbent and heat and mass transfer resistance in packed bed. In order to improve the volumetric power density of the adsorber, it is necessary to increase the production of the sorption rate and the packing density.