Search Results

It is important for vehicle concept planning to estimate fuel economy and the influence of vehicle vibration using virtual engine specifications and a virtual vehicle frame. In our former study, we showed the 1D physical power plant model with electrical starter, battery that can predict combustion transient torque, combustion heat energy and fuel efficiency. The simulation result agreed with measured data. For idling stop system, the noise and vibration during start up is important factor for salability of the vehicle. In this paper, as an application of the 1D physical power plant model (engine model), we will show the result of analysis that is starter shaft resonance and the effect on the engine mount vibration of restarting from idle stop. First, an engine model for 3.5L 6cyl NA engine was developed by energy-based model using VHDL-AMS. Here, VHDL-AMS is modeling language registered in IEC international standard (IEC61691-6) to realize multi physics on 1D simulation.

In recent years, the slip lock-up mechanism has been adopted widely, because of its fuel efficiency and its ability to improve NVH. This necessitates that the automatic transmission fluid (ATF) used in automatic transmissions with slip lock-up clutches requires anti-shudder performance characteristics. The test methods used to evaluate the anti-shudder performance of an ATF can be classified roughly into two types. One is specified to measure whether a μ-V slope of the ATF is positive or negative, the other is the evaluation of the shudder occurrence in the practical vehicle. The former are μ-V property tests from MERCON® V, ATF+4®, and JASO M349-98, the latter is the vehicle test from DEXRON®-III. Additionally, in the evaluation of the μ-V property, there are two tests using the modified SAE No.2 friction machine and the modified low velocity friction apparatus (LVFA).

Driveshafts are composed of a transmission side joint, wheel side joint, and shaft which connect the two joints. The Rzeppa type constant velocity joint (CVJ) is usually selected as the wheel side joint of a drive shaft for front wheel drive automobiles. Due to recent needs of fuel efficiency and lighter weight for vehicles, it is necessary to reduce the joint size and improve the efficiency of a CVJ. In order to reduce the weight, solving tribology details for long life under high contact pressure is an important issue for developing a CVJ. It is difficult to understand the characteristics of a contact surface, such as relative slip velocity or spin behavior, because the outer race, inner race, cage, and balls, act complicatedly and exchange loads at many points. Meanwhile, after joint endurance tests, ball spalling marks at pole of the ball are sometimes observed.

Since the regulations of CO2 emissions have been tightened in each country recently, each automotive manufacturer has responded by bringing competitive technologies that maximize efficiency while promoting vehicle electrification such as xEV. Not only the efficiency, we need to meet or exceed occupant performance and comfort expectations. The climate control system expends a large amount of energy to keep a comfortable environment, having a significant impact on fuel consumption and EV driving range. Therefore, many manufacturers try to save energy and improve occupant comfort quickly by using not only the conventional convective heating by HVAC but also the conductive heating to heat the human body directly such as seat and steering wheel heater. In this study, a radiative heater, which is more efficient than a convective heating to warm anterior thigh and shin where a conductive heating cannot warm, was applied to vehicle.

Automobile manufactures need to adopt new technologies to meet global CO2 (carbon dioxide) emission regulations and better fuel efficiency demands from customers. Also, the production cost should be as low as possible for an affordable vehicle. Therefore, it is advantageous for OEMs to develop fuel efficient technologies which can be controlled by software without additional hardware costs. The coasting control is a fuel efficiency improvement technology that can be implemented by the change of vehicle software only. The coasting control is a technology that reduces the driving resistance (Deceleration) when the driver releases the gas pedal. This technology leads to reducing the energy required for the vehicle to drive and results in improving the real-world fuel economy. In an internal combustion engine (ICE) vehicle, the coasting state is achieved by changing the gear to neutral, and the effect has been discussed and clarified by many previous studies.

Toyota Motor Corporation has developed new Hybrid Vehicle (HV) and Plug in Hybrid Vehicles (PHV) from Compact class to Medium class. These vehicles incorporate newly developed hybrid systems for the improvement of fuel efficiency. The feature of these new generation power control unit is smaller, lighter, and higher efficiency than the previous generation. To adapt to various output systems, a development strategy of new generation Power Control Unit (PCU) was established. Based on the strategy, the development efficiency was improved. In this Paper, the strategy is described.

Increasingly stringent environmental regulations requiring lower CO2 emissions and higher fuel economy have made it essential to develop vehicles with superior fuel efficiency and cleaner emissions. At the same time, there is growing demand for even more powerful and quieter vehicles. To help satisfy these requirements, Toyota Motor Corporation has developed a new 8-speed automatic transmission for front wheel drive vehicles, incorporating its first compact torque converter with a multiple disk lock-up mechanism. This newly developed compact torque converter with a multiple disk lock-up mechanism was designed under the Toyota New Global Architecture (TNGA) development concept to achieve an excellent balance between higher efficiency through the commonization of components and stronger product appeal through installation on a whole family of transmissions. This compact torque converter is compatible with a variety of engines from inline 4-cylinder to V6 configurations.

Various issues must be resolved before sustainable mobility can be achieved, the most important of which are reacting to energy supply and demand, and lowering CO2 emissions. At present, the fact that the vast majority of vehicles run on conventional oil is regarded as a problem for which Toyota Motor Corporation (TMC) is developing various technological solutions. Fuel cell (FC) technology is one of the most promising of these solutions. A fuel cell is an extremely clean device that uses hydrogen and oxygen to generate power without emitting substances like CO2, NOx, or PM during operation. Its energy efficiency is high and it is widely expected to form the basis of the next generation of powertrains. Since 1992, TMC has been working to develop the main components of fuel cell vehicles, including the fuel cell itself, and the high pressure hydrogen tank and hybrid systems.

In recent years, attention has been focused on a hybrid vehicle capable of substantial reductions in CO2 exhaust emissions. This paper describes the newly developed 1.8-liter 2ZR-FXE gasoline engine for use with a hybrid system for compact vehicles, which effectively combines higher driving performance with higher fuel efficiency. This engine was based on the 1.8-liter 2ZR-FE engine with outstanding performance and fuel efficiency. This engine has achieved high thermal efficiency by using the high-expansion ratio cycle “Atkinson cycle”, as with the previous 1NZ-FXE engine. Additionally, a new cooled Exhaust Gas Recirculation (EGR) system and electric water pump were adopted to further improve fuel efficiency. A high efficiency cooler was used to cool the EGR gas, which enabled the introduction of the EGR gas at high load conditions, and exhaust gas temperature was reduced.

Toyota has developed a new continuously variable transmission (CVT) called "Direct Shift-CVT" which is for 2.0-liter class vehicles. This CVT provided not only power transmission by a metal belt held with a conventional pulley but also additional gear mechanism. This CVT is developed to improve fuel efficiency, acceleration characteristic, and quietness. At this CVT, the startup low gear ratio is achieved by gear mechanism and the power is switched by clutches. Since the belt-pulley portion can be realized to be wide range by using only high gear ratio range, the input load into belt-pulley portion is reduced and unprecedented compact and high efficient belt-pulley portion is established. Consequently, the high efficiency in all fields from startup acceleration to high speed driving is achieved to improve fuel efficiency.

Toyota has developed a new Hybrid (HV) transaxle P810 for Mid-Size SUVs to improve fuel efficiency and power performance. The transaxle was developed based on Toyota's new development strategy - Toyota New Global Architecture (TNGA). By adopting technologies to shorten overall length of the transaxle, installation into the same engine compartment of Mid-Size sedans have been realized while also improving the motor output. This paper will introduce technologies regarding the new mount structure for shortening overall length, and furthermore, noise reduction related to this mount structure.

Recently, due to mounting concerns regarding the environment and energy conservation, demand for compact and hybrid vehicles with good fuel economy has been increasing. Toyota Motor Corporation has developed its first hybrid transaxle for installation in sub-compact class vehicles. This new hybrid transaxle is both smaller and lighter than the P410 hybrid transaxle for compact class vehicles, including the 2009 Prius. This was accomplished by creating new designs of the gear train, motor, and motor cooling system, and by adopting advanced technology. This paper describes the major features and performance of this transaxle in detail.

One way to improve the fuel efficiency of HVs is to reduce the losses and size of the Power Control Unit (PCU). To achieve this, it is important to reduce the losses of power devices (such as IGBTs and FWDs) used in the PCU since their losses account for about 20% of the total loss of an HV. Furthermore, another issue when reducing the size of power devices is ensuring the thermal feasibility of the downsized devices. To achieve the objectives of the 4th generation PCU, the following development targets were set for the IGBTs: reduce power losses by 19.8% and size by 30% compared to the 3rd generation. Power losses were reduced by the development of a new Super Body Layer (SBL) structure, which improved the trade-off relationship between switching and steady-state loss. This trade-off relationship was improved by optimizing the key SBL concentration parameter.

The reduction of CO2 emissions has become an imperative duty in order to cope with environmental compliance. For car manufacturers, CO2 emission has been set by regulation and many consumers prefer a fuel efficient car because of the increasing fuel price. In such a situation, reducing engine friction is an effective way of improving fuel efficiency. Among engine parts, the piston counts for a large percentage of the friction losses. In this study, we established a calculation model for estimating piston and piston ring friction. This paper shows how the accuracy of the calculation model was improved by validating against measurements.

Toyota Motor Corporation has developed the new compact-class hybrid vehicle (HV). This vehicle incorporates Toyota Hybrid System II (THS-II) to improve fuel efficiency. For this system we have developed a new power control unit (PCU) that features size reduction, light weight, and high efficiency. We have also improved the ability to mass produce these units with the expectation of rapid popularization of HV. The PCU, which plays an important role in THS-II, is our main focus in this paper. Its development is described.

Toyota Motor has developed a new compact class hybrid vehicle (HV). This vehicle incorporates a new hybrid system to improve fuel efficiency. For this system, a new power control unit (PCU) has been developed that is downsizing, lightweight, and high efficiency. It is also important to have a highly adaptable function that can be applied to various car models. This paper describes the development of PCUs that play an important role in new systems.

Toyota Motor Corporation has developed the new compact-class hybrid vehicle (HV). This vehicle incorporates a new hybrid system for the improvement of fuel efficiency. For this system, a new Power Control Unit (PCU) is developed. The feature of the PCU is downsizing, lightweight, and high efficiency. In expectation of rapid popularization of HV, the aptitude for mass production is also improved. The PCU, which plays an important role in the new system, is our main focus in this paper. Its development is described.

In order to improve the fuel efficiency of Hybrid Electric Vehicles (HEVs), it is necessary to reduce the size and power loss of the HEV Power Control Units (PCUs). The loss of power devices (IGBTs and FWDs) used in a PCU accounts for approximately 20% of electric power loss of an HEV. Therefore, it is important to reduce the power loss while size reduction of the power devices. In order to achieve the newly developed PCU target for compact-size vehicles, the development targets for the power device were to achieve low power loss equivalent to its previous generation while size reduction by 25%. The size reduction was achieved by developing a new RC-IGBT (Reverse Conducting IGBT) with an IGBT and a FWD integration. As for the power loss aggravation, which was a major issue due to this integration, we optimized some important parameters like the IGBT and FWD surface layout and backside FWD pattern.

Cold weather operation has been a major issue for fuel cell hybrid vehicles (FCHV). To counteract the effects of low temperatures on FCHV operation, an approach for rapid warm-up operation based on concentration overvoltage increase and conversion efficiency decrease by limiting oxygen or hydrogen supply was adopted. In order to suppress increases in exhaust hydrogen concentration due to pumping hydrogen during rapid warm-up, dilution control using bypass air and reduction of concentration overvoltage by a minimum voltage guard were implemented. These approaches effectively control waste heat generation and suppress exhaust hydrogen concentrations during cold start and warm-up. These developments were incorporated into the 2008 Toyota FCHV-adv and it was confirmed that the rapid warm-up operation strategy allowed the FCHV-adv to be successfully and repeatedly started at -30°C.

Toyota has been developing various environmentally friendly vehicles to address global environmental concerns. In 1996, Toyota started to sell the battery powered "RAV4" electric vehicle, and introduced the "e-com" in 1997. Late last year, Toyota launched production of the world's first hybrid vehicle, the "PRIUS", doubling the fuel efficiency and drastically reducing the emission of carbon dioxide. Toyota is also conducting research in the area of fuel cell electric vehicles. This paper explains the electric systems of these vehicles, i.e., motor, inverter, Ni-MH battery and control. Some of the technical problems will also be discussed