Search Results

This investigation was aimed at measuring the relative performance of two spray-guided, single-cylinder, spark-ignited direct-injected (SIDI) engine combustion system designs. The first utilizes an outwardly-opening poppet, piezo-actuated injector, and the second a conventional, solenoid operated, inwardly-opening multi-hole injector. The single-cylinder engine tests were limited to steady state, warmed-up conditions. The comparison showed that these two spray-guided combustion systems with two very different sprays had surprisingly close results and only differed in some details. Combustion stability and smoke emissions of the systems are comparable to each other over most of the load range. Over a simulated Federal Test Procedure (FTP) cycle, the multi-hole system had 15% lower hydrocarbon and 18% lower carbon monoxide emissions.

Chassis dynamometer testing was conducted with three on-highway motorcycles produced for the North American market with engine displacements of 296 cc, 749 cc and 1198 cc to better inform criteria pollutant emissions inventories. The motorcycles were tested using US Tier 2 certification fuel over the Federal Test Procedure (FTP), World Motorcycle Test Cycle (WMTC) and a cycle based on a sample of real-world motorcycle driving, informally referred to as the ‘Real World Driving Cycle’ (RWDC). Emissions characterization includes composite, individual test phase and 1Hz cumulative results for various criteria pollutants for each test cycle. Overall, it was found that the higher peak speed rates and peak torque levels observed during the RWDC are more fully represented in the WMTC than the FTP. The use of the WMTC and RWDC cycles generally translated into higher emissions rates compared to the FTP and in particular for nitrogen oxides and carbon monoxide.

This paper covers work performed for the California Air Resources Board and US Environmental Protection Agency by Southwest Research Institute. Emission measurements were made on four in-use off-road two-stroke motorcycles and all-terrain vehicles utilizing oxygenated and non-oxygenated fuels. Emission data was produced to augment ARB and EPA's off-road emission inventory. It was intended that this program provide ARB and EPA with emission test results they require for atmospheric modeling. The paper describes the equipment and engines tested, test procedures, emissions sampling methodologies, and emissions analytical techniques. Fuels used in the study are described, along with the emissions characterization results. The fuel effects on exhaust emissions and operation due to ethanol content and fuel components is compared.

After initial trials on Homogeneous Charge Compression Ignition (HCCI) engine design and tests pursuing feedback control to avoid misfire and knocking over wide transient operation ranges, Engineers at the US Environmental Protection Agency's (EPA) National Vehicle Fuel and Emissions Laboratory identified the crucial engine state variable, MRPR (Maximum Rate of Pressure Rise) and successfully controlled a 1.9L HCCI engine in pure HCCI mode [1]. This engine was used to power a hybrid Ford F-150 truck which successfully ran FTP75 tests in 2004. In subsequent research, efforts have been focused on practical issues such as improving transient rate, system simplification for controllability and packaging, application of production grade in-cylinder pressure sensors, cold start, idling and calibration for ambient conditions as well as oxidation catalyst applications for better turbine efficiency and HC and CO emissions control.

As part of the Midterm Evaluation of the 2017-2025 Light-duty Vehicle Greenhouse Gas Standards, the U.S. Environmental Protection Agency (EPA) developed simulation models for studying the effectiveness of stop-start technology for reducing CO2 emissions from light-duty vehicles. Stop-start technology is widespread in Europe due to high fuel prices and due to stringent EU CO2 emissions standards beginning in 2012. Stop-start has recently appeared as a standard equipment option on high-volume vehicles like the Chevrolet Malibu, Ford Fusion, Chrysler 200, Jeep Cherokee, and Ram 1500 truck. EPA has included stop-start technology in its assessment of CO2-reducing technologies available for compliance with the standards. Simulation and modeling of this technology requires a suitable model of the battery. The introduction of stop-start has stimulated development of 12-volt battery systems capable of providing the enhanced performance and cycle life durability that it requires.

This study is the second in a series of three EPA studies to investigate the effect of fuel reformulations and modifications on exhaust emissions. Both the first and second study in this series of studies were used to support the development of EPA's complex model for the certification of reformulated gasolines. Phase I of the study tested eight fuels on forty vehicles. This study, termed Phase II, tested twelve fuels on a separate fleet of 39 light-duty vehicles. The Phase II fuel parameters studied included Reid Vapor Pressure (RVP), the 50% and 90% evaporated distillation temperatures (T50 and T90), sulfur content, aromatics content, olefin content, oxygenate type and oxygen content. Measured exhaust emissions included total hydrocarbons (THC), oxides of nitrogen (NOx), carbon monoxide (CO), carbon dioxide (CO2), benzene, 1,3-butadiene, acetaldehyde and formaldehyde.

Fourier Transform Infrared Spectroscopy (FT-IR) has been used to measure the exhaust emissions from vehicles during standard driving tests. Comparisons with conventional analyzers for modal tests have been made for the regulated species such as carbon monoxide (CO), nitrogen oxides (NOx) and total hydrocarbon (THC). The concentrations of methane, methanol and formaldehyde were also measured at one second time intervals during several driving tests. The average concentration values for these species were compared to the bag samples for several tests. Modal concentration curves were also calculated for MTBE, ETBE and several other species of interest. The results indicate FT-IR can be used for making modal measurements on the regulated species and non-regulated species in vehicle exhaust emissions. Several studies were performed to evaluate the long-term stability and sensitivity of FT-IR in actual test situations.