Search Results

A Stochastic Reactor Model (SRM) has been used to simulate the transition from Spark Ignition (SI) mode to Homogeneous Charge Compression Ignition (HCCI) mode in a four cylinder in-line four-stroke naturally aspirated direct injection SI engine with cam profile switching. The SRM is coupled with GT-Power, a one-dimensional engine simulation tool used for modelling engine breathing during the open valve portion of the engine cycle, enabling multi-cycle simulations. The model is initially calibrated in both modes using steady state data from SI and HCCI operation. The mode change is achieved by switching the cam profiles and phasing, resulting in a Negative Valve Overlap (NVO), opening the throttle, advancing the spark timing and reducing the fuel mass as well as utilising a pilot injection. Experimental data is presented along with the simulation results.

An established Stochastic Reactor Model (SRM) is used to simulate the transition from Spark Ignition (SI) to Homogeneous Charge Compression Ignition (HCCI) combustion mode in a four-cylinder in-line four-stroke naturally aspirated direct injection SI engine with cam profile switching. The SRM is coupled with GT-Power, a one-dimensional engine simulation tool used for modeling engine breathing during the open valve portion of the engine cycle, enabling multi-cycle simulations. The mode change is achieved by switching the cam profiles and phasing, resulting in a Negative Valve Overlap (NVO), opening the throttle, advancing the spark timing and reducing the fuel mass as well as using a pilot injection. A proven technique for tabulating the model is used to create look-up tables in both SI and HCCI modes. In HCCI mode several tables are required, including tables for the first NVO, transient valve timing NVO, transient valve timing HCCI and steady valve timing HCCI and NVO.

In HCCI engines, the Air/Fuel Ratio (AFR) and Residual Gas Fraction (RGF) are difficult to control during the SI-HCCI-SI transition, and this may result in incomplete combustion and/or high pressure raise rates. As a result, there may be undesirably high engine load fluctuations. The objectives of this work are to further understand this process and develop control methods to minimize these load fluctuations. This paper presents data on instantaneous AFR and RGF measurements, both taken by novel experimental techniques. The data provides an insight into the cyclic AFR and RGF fluctuations during the switch. These results suggest that the relatively slow change in the intake Manifold Air Pressure (MAP) and actuation time of the Variable Valve Timing (VVT) are the main causes of undesired AFR and RGF fluctuations, and hence an unacceptable Net IMEP (NIMEP) fluctuation. We also found large cylinder-to-cylinder AFR variations during the transition.

In recent decades, “physics-based” gas-dynamics simulation tools have been employed to reduce development timescales of IC engines by enabling engineers to carry out parametric examinations and optimisation of alternative engine geometry and operating strategy configurations using desktop PCs. However to date, these models have proved inadequate for optimisation of in-cylinder combustion and emissions characteristics thus extending development timescales through additional experimental development efforts. This research paper describes how a Stochastic Reactor Model (SRM) with reduced chemistry can be employed to successfully determine in-cylinder pressure, heat release and emissions trends from a diesel fuelled engine operated in compression ignition direct injection mode using computations which are completed in 147 seconds per cycle.

Employing detailed chemistry into modern engine simulation technologies has potential to enhance the robustness and predictive power of such tools. Specifically this means significant advancements in the ability to compute the onset of ignition, low and high temperature heat release, local extinction, knocking, exhaust gas emissions formation etc. resulting in a set of tools which can be employed to carry out virtual engineering studies and add additional insight into common IC engine development activities such as computing IMEP, identifying safe/feasible operating ranges, minimizing exhaust gas emissions and optimizing operating strategy. However the adoption of detailed chemistry comes at a greater computational cost, this paper investigates the means to retain computational robustness and ease of use whist reducing computational timescales.

Analyzing the combustion characteristics, engine performance, and emissions pathways of the internal combustion (IC) engine requires management of complex and an increasing quantity of data. With this in mind, effective management to deliver increased knowledge from these data over shorter timescales is a priority for development engineers. This paper describes how this can be achieved by combining conventional engine research methods with the latest developments in process informatics and statistical analysis. Process informatics enables engineers to combine data, instrumental and application models to carry out automated model development including optimization and validation against large data repositories of experimental data.

This research describes the potential to adopt detailed chemical kinetics for practical and potential future fuels using tri-component surrogate mixtures capable of simulating fuel octane “sensitivity” . Since the combustion characteristics of modern fuels are routinely measured using the RON and MON of the fuel, a methodology to generate detailed chemical kinetic mechanisms for these fuels based on these data is presented. Firstly, a novel correlation between various tri-component blends (comprised of i-octane, n-heptane and toluene) and fuel RON and MON was obtained by carrying out standard octane tests. Secondly, a chemical kinetic mechanism for tri-component fuels was validated using a Stochastic Reactor Model (SRM) suite, an in-cylinder engine combustion simulator, and a series of engine experiments conducted in HCCI operating mode.

Regulations on emissions from diesel and gasoline fuelled engines are becoming more stringent in all parts of the world. Hence there is a great deal of interest in developing advanced combustion systems that offer the efficiency of a diesel engine, but with low PM and NOx. One promising approach is that of Partially-Premixed Compression Ignition (PPCI) or Low Temperature Combustion (LTC). Using this approach, PM can be reduced in compression ignition engines by promoting the mixing of fuel and air prior to combustion. This paper describes the application of an advanced combustion simulator for fuels, combustion and emissions to analyze the key processes which occur in PPCI combustion mode. A detailed chemical kinetic model with advanced PM population balance sub-model is employed in a PPCI engine context to examine the impact of ignition resistance on combustion, mixing, ignition and emissions.