Search Results

The insertion loss of louvered terminations positioned at the end of a rectangular duct is determined using acoustic finite element analysis. Insertion loss was determined by taking the difference between the sound power with and without the louvers at the termination. Analyses were conducted in the plane wave regime and the acoustic source was anechoic eliminating any reflections from the source. The effect of different louver configurations on insertion loss was examined. Parameters investigated included louver length, angle, and spacing between louvers. Based on the analyses, equations were developed for the insertion loss of unlined louvers.

The most common approach for measuring the transmission loss of a muffler is to determine the incident power by decomposition theory and the transmitted power by the plane wave approximation assuming an anechoic termination. Unfortunately, it is difficult to construct a fully anechoic termination. Thus, two alternative measurement approaches are considered, which do not require an anechoic termination: the two load method and the two-source method. Both methods are demonstrated on two muffler types: (1) a simple expansion chamber and (2) a double expansion chamber with an internal connecting tube. For both cases, the measured transmission losses were compared to those obtained from the boundary element method. The measured transmission losses compared well for both cases demonstrating that transmission losses can be determined reliably without an anechoic termination. It should be noted that the two-load method is the easier to employ for measuring transmission loss.

As one considers the interrelationship between supplier logistics and performance of JIT assembly plants, the question arises concerning how many hours of parts inventory are appropriate. Low inventories reduce holding costs, throughput times, and (by eliminating storage) material handling costs internal to the plant. Moreover, under the lean philosophy, low inventories enable improved control over part quality and supplier performance and they maintain a healthy stress on the system necessary to motivate improvements. The dollar magnitude of these later savings is intangible but generally considered significant. On the other hand, low inventories also increase the frequency of milkrun routes and the number of suppliers on these routes, hence, increasing transportation costs.

3D printing is a revolutionary manufacturing method that allows the productions of engineering parts almost directly from modeling software on a computer. With 3D printing technology, future manufacturing could become vastly efficient. However, it has been reported that the 3D printed parts exhibit anisotropic behaviors in microstructure and mechanical properties, that is, depending on the positions (infill orientations) that the parts are placed on a printer platform, the properties of resultant parts can vary greatly. So far, studies on anisotropic behaviors of 3D printed parts have been mostly limited to the static properties (modulus of elasticity, failure strength, etc.); there is a lack on the understanding of mechanical responses of 3D printed parts under dynamic conditions. In the present study, the anisotropic behaviors of 3D printed parts are investigated from the dynamic aspect.

Traditional manufacturing processes such as injection or compression molding are often enclosed and pressurized systems that produce homogenous products. In contrast, 3D printing is exposed to the environment at ambient (or reduced) temperature and atmospheric pressure. Furthermore, the printing process itself is mostly “layered manufacturing”, i.e., it forms a three-dimensional part by laying down successive layers of materials. Those characteristics inevitably lead to an inconsistent microstructure of 3D printed products and thus cause anisotropic mechanical properties. In this paper, the anisotropic behaviors of 3D printed parts were investigated by using both laboratory coupon specimens (bending specimens) and complex engineering structures (A-pillar). Results show that the orientation of the infills of 3D printed parts can significantly influence their mechanical properties.

Literature has shown that 3D printed composites may have highly anisotropic mechanical properties due to variation in microstructure as a result of filament deposition process. Laminate composite theory, which is already used for composite products, has been proposed as an effective method for quantifying these mechanical characteristics. Continuous fiber composites traditionally have the best mechanical properties but can difficult or costly to manufacture, especially when attempting to use additive manufacturing methods. Traditionally, continuous fiber composites used specialized equipment such as vacuum enclaves or labor heavy hand layering techniques. An attractive alternative to these costly techniques is modifying discontinuous fiber additive manufacturing methods into utilizing continuous fibers. Currently there exist commercial systems that utilize finite-deposition (FD) techniques that insert a continuous fiber braid into certain layers of the composite product.

The sound attenuation performance of microperforated panels (MPP) with adjoining air cavity is demonstrated. First of all, simulated results are shown based upon Maa's work investigating the parameters which impact MPP performance [1]. It is shown that the most important parameter is the depth of the adjoining cavity. Following this, an experimental study was undertaken to compare the performance of an MPP to that of standard foam. Following this, two strategies to improve the MPP performance are implemented. These include partitioning the air cavity and having a cavity with varying depth. Both strategies show a marked improvement in MPP attenuation.

This paper considers two questions: how does one know when a boundary element mesh is reliable, and what are the advantages and potential pitfalls of various methods for sound radiation prediction. To answer the first question, a mesh checking method is used. With this method velocity boundary conditions are calculated on the nodes of the mesh using a point source or sources placed inside the mesh. A boundary element program is then used to calculate the sound power due to these boundary conditions. The result is compared to the known sound power of the point source or sources. This method has been used to determine the maximum frequency of a mesh, how many CHIEF points to use, etc. The second question is answered by comparing the results of several numerical methods to experimental results for a running diesel engine. The methods examined include the direct and indirect boundary element methods and the Rayleigh integral.

The design and development of new biologically inspired technologies based on intelligent materials that are capable of sensing the levels of target biomolecules and, if needed, trigger appropriate countermeasures to regulate biological processes and rhythms of the astronauts is being undertaken in our laboratories. This is accomplished by coupling biologically inspired sensors that monitor the levels of the target biomolecules with intelligent polymeric materials that can regulate the release of a countermeasure. The technology developed here integrates sensors and artificial muscle material into a self-regulating device that can perform with minimal crew intervention. Further, it takes advantage of microfabrication technology to construct lightweight and robust responsive delivery systems. These “intelligent” devices address the need for the control and regulation of biological processes and rhythms under spaceflight conditions.

Transfer path analysis is commonly used to determine input forces indirectly utilizing measured responses and transfer functions. Though it is recommended that the source should be detached from the vibrating structure when measuring transfer functions, engineers and technicians frequently have a difficult time in doing so in practice. Recently, a substitute for inverse force determination via transfer path analysis has been suggested. The indirectly determined forces are termed blocked forces and are usable so long as the source and machine are not detached from one another. Blocked forces have the added advantage of being valid even if the machine structure is modified. In this research, a typical automotive engine cover is considered as a receiver structure and is bolted to a plastic source plate excited by an electromagnetic shaker.

Over the past decade crash rates of younger drivers have been increasing despite a decrease in their driver population. This study examined specific driving maneuvers whose unsuccessful undertaking results in specific types of crashes involving these drivers. Four types of crashes were identified including crashes at intersections, rear end, crashes resulting from passing maneuvers and single vehicle crashes. For all crashes a general trend of decreasing involvement with increasing age was observed indicating that inexperience is the largest single contributor to the increased crash rates of younger drivers. Increasing the level of awareness among young drivers about these issues and their likely crash involvement seems to be the only viable approach.

Helmholtz resonators are often used in the design of vehicle mufflers to target tonal noise at a few specific low frequencies generated by the engine. Due to the uncertainty of temperature variations and different engine speeds, multiple resonators may have to be built in series to cover a narrow band of frequencies. Double-tuned Helmholtz resonators (DTHR) normally consist of two chambers connected in series. Openings or necks are created by punching small slots into a thin-walled tube which provide a natural neck passage to the enclosing volume of the Helmholtz resonator. In this paper, numerical analyses using both the boundary element (BEM) and the finite element (FEM) methods are performed and simulation results are compared against one another. A typical real-world muffler configuration commonly used in passenger vehicles is used in a case study.

Additive manufacturing is slowly changing how components are developed and manufactured. As the technology develops over time, it is anticipated that industry will 3D print sound absorbers in production. Configurations may be considered that would be difficult to manufacture in another way. For exploratory purposes, several designs were 3D printed and positioned in an impedance tube for testing. Though the absorbers developed are based on well-established strategies, the absorbers considered are either difficult to manufacture by another means or take advantage of the unique features of 3D printed parts. The samples measured include long perforations, lightweight panels, and Helmholtz resonators with spiral wound necks. Selected results are compared with acoustic finite element analysis.

Microperforated panel (MPP) absorbers are rugged, non-combustible, and do not deteriorate over time. That being the case, they are especially suitable for long term use in harsh environments. However, the acoustic performance is modified when contaminated by dust, dirt, or fluids (i.e. oil, water). This paper examines that effect experimentally and correlates the absorption performance with Maa's theory for micro-perforated panels. Transfer impedance and absorption coefficient are measured for different levels of aluminum oxide and carbon dust accumulation. The amount of dust contamination is quantified by measuring the luminance difference between clean and dirty panels with a light meter. The porosity and hole diameter in Maa's equation are modified to account for dust obstruction. The effect of coating the MPP with oil, water, and other appropriate viscous fluids was also measured. This effect was simulated by modifying the viscous factor in Maa's equation.

Discontinuous or short-fiber composites are traditionally less expensive and are normally less difficult to manufacture than continuous fiber composites, while still retaining some of the benefits of reinforcing fibers. Similarly to continuous fibers, the volume ratio influences the mechanical properties of the composite. In addition the ratio of the length and diameter of the reinforcing fibers also plays a significant role. This ratio (also known as the aspect ratio) adds another variable to the anisotropic properties of lamina plies where now not only the content of fibers but also the dimensions of the fibers themselves play a role. Short fiber reinforced composites are already used in additive manufacturing techniques; however, the amount of carbon fiber and the length of the discontinuous strands in the filaments are normally not stated or vary greatly.

The population of drivers over the age of 65 has been rapidly increasing since the early 1970's and this trend is expected to continue in the future. Aging could affect visual and cognitive abilities of elderly drivers and possibly impair their ability to operate a vehicle safely. This study examined the impact of this population on traffic safety over a 20-year period. The factors of age and cohort are examined to determine their influence on the crash involvement of elderly drivers. Age factors have been shown to be decisive in crashes resulting from complex situations, whereas cohort effects play a more dominate role in less demanding circumstances.

Micro-perforated (MPP) panels are acoustic absorbers that are non-combustible, acoustically tunable, lightweight, and environmentally friendly. In most cases, they are spaced from a wall, and that spacing determines the frequency range where the absorber performs well. The absorption is maximized when the particle velocity in the perforations is high. Accordingly, the absorber performs best when positioned approximately a quarter acoustic wavelength from the wall, and larger cavity depths improve the low frequency absorption. At multiples of one half acoustic wavelength, the absorption is minimal. Additionally, the absorption is minimal at low frequencies due to the limited cavity depth behind the MPP. By partitioning the backing cavity, the cavity depth can be strategically increased and varied. This will improve the absorption at low frequencies and can provide absorption over a wide frequency range.

3D printing is a revolutionary manufacturing method that allows the productions of engineering parts almost directly from modeling software on a computer. With 3D printing technology, future manufacturing could become vastly efficient. However, the procedures used in 3D printing differ substantially among the printers and from those used in conventional manufacturing. The objective of the present work was to comprehensively evaluate the mechanical properties of engineering products fabricated by 3D printing and conventional manufacturing. Three open-source 3D printers, i.e., the Flash Forge Dreamer, the Tevo Tornado, and the Prusa, were used to fabricate the identical parts out of the same material (acrylonitrile butadiene styrene). The parts were printed at various positions on the printer platforms and then tested in bending. Results indicate that there exist substantial differences in mechanical responses among the parts by different 3D printers.

This paper explores the use of inverse boundary element method to identify aeroacoustic noise sources. In the proposed approach, sound pressure at a few locations out of the flow field is measured, followed by the reconstruction of acoustic particle velocity on the surface where the noise is generated. Using this reconstructed acoustic particle velocity, the acoustic response anywhere in the field, including in the flow field, can be predicted. This approach is advantageous since only a small number of measurement points are needed and can be done outside of the flow field, and a relatively fast computational time. As an example, a prediction of vortex shedding noise from a circular cylinder is presented.

This paper is concerned with the prediction and experimental verification of the interior noise of cabs used on construction, highway, and farm equipment. The typical heavy equipment cab is totally enclosed and partially lined with absorbing materials but is much stiffer and more massive than automobile passenger compartments. The process to analyze a construction cab is explained in detail. Selected results are also presented to show the value of the method.