Search Results

This paper describes a case study led by Science Applications International Corporation (SAIC) of Dayton, OH USA and Dearborn Group Inc. to prove the feasibility of employing Telematics technologies to the vehicle test and measurement industry. Many test functions can be automated through the use of secure wireless technologies. For example, vehicle data can be dynamically monitored on the vehicle and data meeting pre-determined criteria could be downloaded via the wireless communications center. Additionally, central, real-time wireless monitoring of vehicle fleets provides the vehicle fleet manager with the ability to manage multiple tests simultaneously, thus improving efficiencies and potentially reducing manpower costs and compressing test schedules.

Most of the present electric vehicle (EV) on-board chargers utilize a conventional design, i.e., a boost-type Power Factor Correction (PFC) controller followed by an isolated DC/DC converter. Such design usually yields a ~94% wall-to-battery efficiency and 2~3kW/L power density at most, which makes a high-power charger, e.g., 20kW module difficult to fit in the vehicle. As described in this paper, first, an E-mode GaN HEMT based 7.2kW single-phase charger was built. Connecting three such modules to the three-phase grid allows a three-phase >20kW charger to be built, which compared to the conventional three-phase charger, saves the bulky DC-bus capacitor by using the indirect matrix converter topology. To push the efficiency and power density to the limit, comprehensive optimization is processed to optimize the single-phase module through incorporating the GaN HEMT switching performance and securing its zero-voltage switching.

Tubular sections are found in many automotive structural components such as front rails, cross beams, and sub-frames. They are also used in other vehicular structures, such as buses and rails. In many of these components, smaller tubular sections may be joined together using an adhesive to build the required structure. For crash safety applications, it is important that the joined tube sections be able to provide high energy absorption capability and withstand the impact load before the adhesive bond failure occurs. In this study, single lap tubular joints between two aluminum tubes are investigated for their crush performance at both quasi-static and high impact speeds using finite element analysis. A crash optimized adhesive Betamate 1496 is considered. The joint parameters, such as adhesive overlap length, tube diameters and tube lengths, are varied to determine their effects on energy absorption, peak and mean loads, and tube deformation mode.

This paper presents results of two surveys, namely, a photographic measurements survey and a rider survey, conducted to determine how the type and origin of a motorcycle related to motorcycle dimensions, rider characteristics, seating posture, and motorcycle controls and displays. In the photographic survey, 12 most popular motorcycles covering three types (cruiser, sport, and touring) and three origins (Europe, Asia and North America) were measured from photographs taken in a standardized procedure with and without a rider. The data showed that the Asian and North American cruisers were very similar in all dimensions. These include seat height, seat to handlebar location, seat to foot rest location, foot rest size, and handgrip stance. This resulted in similar rider posture. North American sport motorcycles were more like cruisers than the Asian and European sport motorcycles.

Semi-trucks, specifically class-8 trucks, have recently become a platform of interest for autonomy systems. Platooning involves multiple trucks following each other in close proximity, with only the lead truck being manually driven and the rest being controlled autonomously. This approach to semi-truck autonomy is easily integrated on existing platforms, reduces delivery times, and reduces greenhouse gas emissions via fuel economy benefits. Level 1 SAE fuel studies were performed on class-8 trucks operating with the Auburn Cooperative Adaptive Cruise Control (CACC) system, and fuel savings up to 10-12% were seen. Enabling platooning autonomy required the use of radar, global positioning systems (GPS), and wireless vehicle-to-vehicle (V2V) communication. Poor measurements and state estimates can lead to incorrect or missing positioning data, which can lead to unnecessary dynamics and finally wasted fuel.

In frontal collision of vehicles, the front bumper system is the first structural member that receives the energy of collision. In low speed impacts, the bumper beam and the crush cans that support the bumper beam are designed to protect the engine and the radiator from being damaged, while at high speed impacts, they are required to transfer the energy of impact as uniformly as possible to the front rails that contributes to the occupant protection. The bumper beam material today is mostly steels and aluminum alloys, but carbon fiber composites have the potential to reduce the bumper weight significantly. In this study, crash performance of bumper beams made of a boron steel, aluminum alloy 5182 and a carbon fiber composite with steel crush cans is examined for their maximum deflection, load transfer to crush cans, total energy absorption and failure modes using finite element analysis.

There is great value in applying lean philosophies and methods to the product creation process, especially in today's competitive environment. Customers now demand better quality (especially a better fit with the product's intended use) and new products with even greater frequency than in the past. The integration of lean methodology throughout product creation is an obvious choice as a systematic way of meeting customer demands. Lean methods result in shorter time to market because understanding and meeting customer wants and needs is an integral starting point in the process. A more in-depth use of lean methods results in better quality and a reduced cost of product creation. Because of more frequent product changes, the cost of the product determined during product creation becomes even more critical. Further, if product creation costs are not reduced, the cost to the customer will increase, putting the product and the company in a less competitive position.

The objective of the paper is to present a unique design approach and its outputs: the design concepts for automotive center consoles for a near term SUV that can be produced in 2-3 years, and the second for, a more futuristic SUV, that could be produced in 10 or more years. In the first phase of this two phase project, we benchmarked center consoles from a number of existing and concept vehicles, analyzed available data (e.g. J.D. Power customer feedback surveys), and conducted studies (e.g. survey of items stored in the vehicles, item location preferences in the console area) to understand customer/user needs in designing the center consoles. In the second phase, we provided the information generated in the first phase to four groups of student teams who competed to create winning designs of the center consoles.

This paper describes a research project currently in-progress to develop a parametric model of a vehicle for use in early design stages of a new vehicle program. The model requires key input parameters to define the kind of new vehicle to be designed — in terms of details such as its intended driver/user population, vehicle type (e.g. 2-box, 3-box designs), and some key exterior and interior dimensions related to its size and proportions. The model computes and graphically displays interior package, ergonomics zones for driver controls and displays, and field of views through window openings. It also allows importing or inputting and superimposing and manipulating exterior surfaces created by a designer to assess compatibility between the interior occupant package and the vehicle exterior.

As intelligent automated vehicle technologies evolve, there is a greater need to understand and define the role of the human user, whether completely hands-off (L5) or partly hands-on. At all levels of automation, the human occupant may feel anxious or ill-at-ease. This may reflect as higher stress/workload. The study in this paper further refines how perceived workload may be determined based on occupant physiological measures. Because of great variation in individual personalities, age, driving experiences, gender, etc., a generic model applicable to all could not be developed. Rather, individual workload models that used physiological and vehicle measures were developed.

This paper presents results of a study conducted to determine differences in older (over age 55) and younger (under age 35), male and female drivers while entering and exiting vehicles with three different body styles - namely, a large sedan, a minivan and a full-size pick-up truck. Thirty-six drivers (males and females, ages 25 to 89 years) who participated in this study were first measured for their anthropometric, strength and body flexibility measures relevant to the entry/exit tasks. They were asked to first get in each vehicle and adjust their preferred seating position. Then, they were asked to get in the vehicle and their entry time was measured. Their entry maneuver was also video taped and they were asked to rate the level of ease/difficulty (using a 5-point scale) in entering. Similar procedure and measurements were conducted during their exit from each vehicle.

Owing to their weight saving potential and improved flexural stiffness, metal-polymer-metal sandwich laminates are finding increasing applications in recent years. Increased use of such laminates for automotive body panels and structures requires not only a better understanding of their mechanical behavior, but also their formability characteristics. This study focuses on the formability of a metal–polymer-metal sandwich laminate that consists of AA5182 aluminum alloy as the outer skin layers and polypropylene (PP) as the inner core. The forming limit curves of Al/PP/Al sandwich laminates are determined using finite element simulations of Nakazima test specimens. The numerical model is validated by comparing the simulated results with published experimental results. Strain paths for different specimen widths are recorded.

This paper describes a unique interior design and multidisciplinary process implemented by the faculty and students to develop the interior for a Low Mass Vehicle (LMV). The 103 inch LMV was designed with the goal of about 30% reduction in weight than a typical class C segment vehicle and would require low investment in manufacturing. In the early stages of the program, the UM-Dearborn team developed detailed requirements of the vehicle interior based on the vehicle's exterior developed using a similar process. The requirements were given to a senior class of automotive design students from the College of Creative Studies in Detroit to create different interior design themes. Approximately twenty-five interior design themes were judged by a panel of automotive industry experts, and a winning design was selected.

A systematic benchmarking study was performed to investigate the acoustic performance of production floor coverings (i.e. carpets) of vehicles. A larger number of passenger cars including compact, mid-size, full size, and a truck were selected. The floor coverings were removed from these vehicles and evaluated both on absorption and sound transmission loss (STL) performances. The methodology used and the experimental results are presented in this paper. It was discovered that the design of the carpet is more important than the materials used. In addition, a carpet with highest absorption does not necessarily have the best STL and vice versa. However, an optimum design could achieve high performance in both categories.

In military vehicles reliability can sometimes be a more important issue than cost. With that in perspective, this paper discusses the load availability and reliability issues in automotive multiplexed wiring harness systems, which are potentially useful in the military, and compares the same with a regular non-multiplexed system. For that purpose, a figure of merit or metric is introduced, and the load availability is described in terms of this metric, which depends on the architecture chosen.

This paper presents a design and development approach for automotive bucket seat frame using a parametric modeling and a finite element analysis methodology. This approach is expected to help build a lightweight seat structure quickly and efficiently. This approach is general, and it can be applied in designing and developing any mechanical structural component. The design process involves, first parametric modeling of the front bucket seat frame using Pro E. This CAD model was then optimized using optimization software called Optistruct, for two cases of load case and boundary condition. The optimized design was then tested for FMVSS seat requirements using LS-DYNA. The dynamic nature of the design approach helps in changing design parameters during different stages of the design process, until the seat structure satisfies the design criteria and the strength requirements. The construction and testing of this design and the design model are still under progress.

Autonomy for multiple trucks to drive in a fixed-headway platoon formation is achieved by adding precision GPS and V2V communications to a conventional adaptive cruise control (ACC) system. The performance of the Cooperative ACC (CACC) system depends heavily on the reliability of the underlying V2V communications network. Using data recorded on precision-instrumented trucks at both ACM and NCAT test tracks, we provide an understanding of various effects on V2V network performance: Occlusions - non-line-of-sight (NLOS) between the Tx and Rx antenna may cause network signal loss. Rain - water droplets in the air may cause network signal degradation. Antenna position - antennas at higher elevation may have less ground clutter to deal with. RF interference - interference may cause network packet loss. GPS outage - outages caused by tree cover, tunnels, etc. may result in degraded performance. Road curvature - curves may affect antenna diversity.

Nowadays, the automotive industry is experiencing the advent of unprecedented applications with connected devices, such as identifying safe users for insurance companies or assessing vehicle health. To enable such applications, driving behavior data are collected from vehicles and provided to third parties (e.g., insurance firms, car sharing businesses, healthcare providers). In the new wave of IoT (Internet of Things), driving statistics and users’ data generated from wearable devices can be exploited to better assess driving behaviors and construct driver models. We propose a framework for securely collecting data from multiple sources (e.g., vehicles and brought-in devices) and integrating them in the cloud to enable next-generation services with guaranteed user privacy protection.

This paper describes the design and application of a business simulation to help train employees about the new business model and culture that for an automotive supplier company that designs connected vehicle and other advanced electronic products for the automotive industry. The simulation, called SIM-i-TRI, is a three to four day collaborative learning activity that simulates the executive, administrative, engineering, manufacturing, and marketing functions in three divisions of a manufacturer that supplies parts and systems to customers in industries similar to the automotive industry. It was originally designed to support the new employee orientation at the Tier 1 supplier and to provide the participants a safe environment to practice the lessons from the orientation. The simulation has been used several times a month in the US, England, and Germany for over four years.

This paper presents results of a five phase study conducted to evaluate touch feel and appearance of door armrest materials. Seven different production door armrests with different material characteristics such as softness, smoothness, compressibility, texture, etc. were evaluated. In the first phase, the subjects seated in a vehicle buck in their preferred seating position with the armrests adjusted at their preferred heights, provided ratings on a number of touch feel and appearance of the door armrest materials using 5-point semantic differential scales. In the second phase, the armrests were presented to each subject in all possible pairs and they were asked to select preferred armrest material in each pair.