Search Results

Nickel based superalloys have a wide range of applications due to high mechanical strength at high temperatures, fracture toughness and resistance to corrosion. However, because of their outstanding properties, it is considered as the difficult to machine materials. Inconel alloy X-750 is used extensively in rocket-engine thrust chambers. Airframe applications include thrust reversers and hot-air ducting systems along with large pressure vessels are formed from Inconel alloy X-750. Moreover, the comparative analysis of machinability aspect using coated carbide inserts is reported few. The current study explains the machinability investigation on Inconel alloy X-750 superalloys using coated carbides. To collect the experimental data, the L16 experimental design plan is used to experiment with a machining length of 40 mm.

The present work compares the tribological properties of ZnO (Zinc Oxide) nanoparticle based lubricant with ZDDP (zinc dialkyl dithiophosphate) based lubricant. The nanolubricant was prepared by mixing the nanoparticles in base oil followed by ultrasonification and ZDDP based lubricant was prepared by mixing ZDDP and stirring with base oil. Base oil used was mineral base oil. Both the lubricants were tested at three different temperatures, loads and roughness values. The test was carried out on AISI 52100 steel samples prepared by wire cutting and were grinded to three different levels of surface roughness. Friction and wear tests were performed using a reciprocating sliding tribo-tester at three different loads and temperatures. Taguchi orthogonal array was used to reduce the number of experiments. SEM, EDS and AFM analysis were carried out to study the surface wear phenomenon.

Vehicle aerodynamic drag reduction is the effective technique to enhance the fuel economy, performance and top speed of a vehicle. Out of the total drag, the underbody drag contributes about 40-50% by the parts like wheel arch, wheel housing, and the wheels. This further increases in the case of vehicles with higher CG. Thus, it seems logical to focus attention on the underbody aerodynamic drag reduction. In this study, an active spoiler is placed towards the front end of the vehicle which will divert the air flow from the front towards the radiator. The active spoiler revolves according to the signals received from the radar sensors placed at the lower end to detect obstacles which will prevent it from damage. The aim of the study is to examine the effect of the air flow diversion on underbody drag. The effect of air flow diversion on fuel consumption, radiator effectiveness and top speed is numerically evaluated.

This paper demonstrates the sloshing phenomena of a cylindrical tank with and without baffles. The main objective of this study is to design baffles of different configurations to reduce sloshing in a cylindrical tank partially filled with gasoil-liquid subjected to only longitudinal acceleration and deceleration. Two different baffle designs have been introduced in the present study. A 3-D transient analysis of a cylindrical tank was carried out using ANSYS-FLUENT with and without baffles. Volume of Fluid (VOF) method was used to study the free surface profile of the fluid in the considered tank. Pressure distribution, velocity distribution and force distribution have been studied in the present study. It has been observed that the new design of baffle was able to reduce sloshing effectively.

This paper summarizes the research work incorporated in the exploration of the potential of swirling in CI Engine and designing of a new mechanism, particularly at inlet, to deliver it to improve the in-cylinder air characteristics to eventually improve mixing and combustion process to improve the engine performance. The research is concentrated on the measures to be done on engine geometry so as to not only deliver advantage to any specific fuel. According to the CI combustion theory, better engine performance may be achieved with Higher Viscous Fuel by improving the in-cylinder air-fuel mixing by increasing the swirl (rotation of air view from top of the cylinder) and tumble (rotation of air view from front of the cylinder) of in-cylinder air inside the fuel-injected region. The proposed inlet component is embedded with airfoil and is suitably designed after being iterated from four steps.

Considerable weight of an automobile is constituted by the engine and there is scope for improvement in fuel efficiency and emission control through optimization of weight in the engine. In this work, AlSi10Mg alloy produced by the direct metal laser sintering (DMLS) is suggested for engine application which is a lightweight aluminum alloy. Mechanical properties like tensile strength, compressive strength, and hardness of both cast and DMLS manufactured alloy are compared followed by analysis of SEM images of tensile test fractured surfaces. Reciprocating wear test is carried out for one lakh cycles at 125°C temperature with SAE 40 grade oil as lubricant. Co-efficient of friction (COF), wear rate of the cast and DMLS manufactured samples are compared. Wear patterns are analyzed using SEM images of the wear tracks.

Friction Stir Welding (FSW) is a widely used solid state welding process in which its heats metal to the below recrystallization temperature due to frictional force. FSW mostly avoids welding defects like hot cracking and porosity which are mainly occur in conventional welding techniques. In this process the combination of frictional force and the mechanical work provide heating the base metal to get defect free weld joints. Aluminium Alloys 2014 and 6061 are generally used in a wide range of automobile applications like Engine valves and tie rod, shipbuilding, and aerospace due to their high corrosion resistance, lightweight, and good mechanical properties. In the present work, aluminium alloys of AA6061 and AA2014 were effectively welded by friction stir welding technique. The tool rotational speed, travel speed, and tool profile are the important parameters in FSW process. High Speed Steel (HSS) tool with Hexagonal profile is used for this joining.

Epoxy carbon fiber composite materials are known for their light weight and high performance. They can be effective substitutes for commonly used materials for making drive shafts. Fiber orientation angle plays a major role in determining such a drive shaft’s responses. The responses considered in this paper are critical buckling torque, fundamental natural frequency and total deformation. A drive shaft made of epoxy carbon unidirectional prepreg is generated using ANSYS 18.0 ACP Composite Prepost. The objective of this paper is to determine an optimal configuration of fiber orientation angles for four, five and six-layered epoxy carbon drive shaft which tends to increase critical buckling torque and fundamental natural frequency while decreasing the total deformation. The optimal configuration which satisfies this objective for the three responses is identified by Minitab 17 statistical software.

Suspension system of a vehicle plays an important role to carefully control motion of the wheel throughout the travel. The vertical and the lateral dynamics (ride and handling) is affected by the unsprung-to-sprung mass ratio. Lower value of this mass ratio leads to enhanced performance of the car. To optimize the unsprung mass of the car, design of control arm plate is optimized with Aluminum material and Carbon fibre reinforced composite control arms framework are used to achieve high stiffness to weight ratio. These leads to increase in overall power to weight ratio of the car which helps to deliver maximum performance to the wheels. Through analysis of real-life working conditions of the entire steering knuckle assembly in ACP pre- post ANSYS 18.1 with the defined boundary conditions, equivalent stress and total deformations are obtained. Based on the results, geometrical topology of the control arms plates is further optimized.

The main purpose of this study is to investigate additive manufactured Inconel super alloy subjected to cryogenic treatment (CT). Cryogenic treatment is mainly used in aerospace, defense and automobile application. Direct metal laser sintering is an additive manufacturing technique used for manufacturing of complex and complicated functional components. Inconel is an austenitic chromium nickel based super alloy often used in the applications which require high strength & temperature resistant. In this work, a study is carried out on microstructure and mechanical properties of additive manufactured Inconel 718 when subjected to cryogenic treatment at three different time intervals. The micro-structural evolution of IN718 super-alloy before and after CT was investigated by both optic microscope and scanning electron microscope. Surface roughness and hardness at different CT time intervals has also analyzed. Additionally, XRD technique was used to analyze the surface residual stress.

This paper describes the modelling and electromagnetic analysis of Permanent Magnet Brushed Direct Current (PMBDC) motor using Finite Element Analysis (FEA) software packages. The designed motors referred in this analysis are fit for use in applications of the electronic throttle control and exhaust gas recirculation in automobiles. Performances of the designed PMBDC models are compared with the traditionally used machines. Three PMBDC models with different operating characteristics are proposed for the two applications. Each model is suitable for use in both applications. Cost analysis of the motors is also carried out, and comparison with the traditionally used machines is done.

In the present paper, to predict the process relation between laser-assisted machining parameters and machinability characteristics, statistical models are formulated by employing surface response methodology along with artificial neural network. Machining parameters such as speed of cut; the rate of feed; along with the power of laser are taken as model input variables. For developing confidence limit in collected raw experimental data, the full factorial experimental design was applied to cutting force; surface roughness; along with flank wear. Response surface method (RSM) with the least square method is used to develop the theoretical equation. Furthermore, artificial neural network method has been done to model the laser-assisted machining process. Then, both the models (RSM and ANN) are compared for accuracy regarding root mean square error (RMSE); model predicted error (MPE) along with the coefficient of determination (R2).

In recent years, aluminum metal matrix composites (Al-MMC) are found as a potential material for numerous applications owing to its excellent tribological and mechanical properties. In this work, the machining characteristics of aluminum alloy (Al7075) reinforced with TiC/MoS2 having nanoparticle has been studied. The samples of aluminum metal matrix composites by varying TiC in 0, 2 and 4 and MoS2 in 0 and 2 of the percentage weight of aluminum alloy (Composite 1(Al7075), Composite 2 (Al7075/2TiC/2MoS2) and composite 3 (Al7075/4TiC/2MoS2), respectively) are fabricated by the stir-casing method. The turning characteristics of the developed metal matrix composites are studied at various parameters such as cutting velocity (30 m/min, 60 m/min and 90 m/min), cutting depth (0.5 mm, 1.0 mm and 1.5 mm) and composites (1, 2 and 3) using TiN coated cutting tool by dry turning at 0.05 mm/rev feed rate.

The experimental investigation aims to improve natural composite materials aligned with feasible development principles. These composites can be exploited across several industries, including the automobile and biomedical sectors. This research employs date seed powder and neem gum powder as reinforcing agents, along with polyester resin as the base material. The fabrication route comprises compression moulding, causing the production of the natural composite material. This study focuses extensively on mechanical characteristics such as tensile strength, flexural strength, hardness, and impact resistance to undergo comprehensive testing. Furthermore, the chemical properties of the composites are examined using the FTIR test to gain understanding by integrating different proportions of date seed powder (5%, 10%, 15%, and 20%) and neem gum powder (0%, 3%, 6%, and 9%) in the matrix phase.

Rising energy demands, ecological deterioration and diminution of fossil fuels has necessitated the researchers to search for alternatives. With alternate fuels like Liquefied Petroleum Gas (LPG), hydrogen and alcohol based fuels, it is easier to substitute with the present engine without many alterations. Excellent chemical properties of these fuels make them favorable for lean burn operation which makes it a cost effective option to achieve goals of better fuel economy and controlled emissions. In this regard, experimental studies were carried out to examine the effects of LPG with different proportions of alcohols like ethanol and methanol (5, 10 and 20%) on the performance, emission and combustion characteristics of a single cylinder SI engine operated at a constant speed of 1500 rpm with a optimized compression ratio of 10.5:1 under full throttle opening conditions at varying equivalence ratio.

Nickel based materials of Nimonic C-263 and Waspaloy are used nowadays for aerospace applications owing to its superior strength properties that are maintained at a higher temperature. Tool wear and cutting temperature in the vicinity of cutting edge are two essential machinability characteristics for any cutting tool. In this regard, this study is pursued to examine the influence of factors on measuring of tool wear (Vba) and cutting temperature (Ts) during dry machining of two alloys studied experimentally based on Taguchi method and response surface methodology. Taguchi’s L16 orthogonal array is used to design the experiment and a PVD (TiAlN), CVD (TiN/Al2O3/TiCN) coated carbide inserts are used on turning of two alloys. The factor effect on output responses are studied using analysis of variance, empirical models, and responses surface 3D plots. To minimize the response and to convert into one single optimum level, responses surface desirability function approach is applied.

Composites materials are substituting constituents for traditional materials due to their remarkable properties, and the addition of nanoparticles gives a new development in the material domain. The nanoparticles influence on fabrication and machinability investigation study is essential as the composites to be used in applications like automotive and aerospace. The current study investigates the machinability characteristics of Al2219 based metal composites reinforced with nanoparticles of SiN/MoS2. Al2219- reinforcements (SiN and MoS2) composites are fabricated by the method of stir casting. Four different compositions (Al2219/SiN (2 wt% and 4 wt%), , Al2219/2 wt.% SiN/ 2 wt.% MoS2, Al2219/2 wt.% MoS2) are fabricated by varying the different weight percentages of nanoparticles reinforcements. An attempt is made to study the investigation analysis of force, surface roughness, and tool wear using CNC machine lathe to consider the effect of cutting speed, cutting depth, and samples.

The aim of this paper is to demonstrate the methodology to simulate the induced stresses/strains due to thermo-mechanical loading of automobile brake drum.. The brake drum undergoes mechanical load due to applied brake pressure and thermal load due to friction generated between brake pad and brake drum while brake is applied. This coupled thermo-mechanical loading affects the life of the brake drum as the stiffness of the brake drum is reduced. The conventional method of simulating this problem is done using Lagrangian discretization in which the load is applied and inertia effect due to angular velocity is applied to a drum at static condition. In contrast, in this paper Eulerian discretization is adopted for finite element analysis, in which drum brake model is discretized as spatially dependent that facilitates actual rotation of brake drum with simultaneous application of brake load resulting more precise simulation.

Vehicle collisions are a major concern in the modern automotive industry. To ensure the passenger safety, major focus has been given on energy absorption pattern on the crumple zone during collision, which lead to the implementation of new design of the crash box for low speed collision. The main aim of this research is optimization of the conical shaped structure based on its mean diameter, graded thickness and semi apical angle. Further, to decrease initial peak load of the conical crash box, corrugations are integrated on structure and optimized based on different parameters, such as number of corrugations, pattern of corrugation relative to both tubes and amplitude of corrugation. The concept of bi-tubular structure is proposed to improve both specific energy absorption and initial peak load during crash event. A finite element model is created to perform parametric study on corrugated conical tube based on axial load conditions at low velocity.

Collection of various data from sensed data or raw availability of data from transcript or interdependency of data from various sources is a tedious task in a real time scenario like an Indian context is considered. Planning to find a solution to collect the data from various vehicular devices about the information related to the pollution becomes a cumbersome job. The need of the data, under what time duration data has to be transmitted, how they are interconnected and whether data needs to be stored or how they are processed is a major question that arise when dealing with collecting data and internetworking with various vehicular devices. A study of two different types of approaches for internetworking between the devices is discussed. One related to real time setup of mobile application and other with the dynamic cluster approach when the nodes are moving in a region was considered.