Search Results

Pre-chamber spark ignition technology can stabilize combustion and improve thermal efficiency of lean burn natural gas engines. During compression stroke, a homogeneous lean mixture is introduced into pre-chamber, which separates spark plug electrodes from turbulent flow field. After the pre-chamber mixture is ignited, the burnt jet gas is discharged through multi-hole nozzles which promotes combustion of the lean mixture in the main chamber due to turbulence caused by high speed jet and multi-points ignition. However, details mechanism in the process has not been elucidated. To design the pre-chamber geometry and to achieve stable combustion under the lean condition for such engines, it is important to understand the fundamental aspects of the combustion process. In this study, a high-speed video camera with a 306 nm band-pass filer and an image intensifier is used to visualize OH* self-luminosity in rapid compression-expansion machine experiment.

A numerical study was carried out to investigate combustion characteristics of a dual-fuel gas diesel engine, using a multi-dimensional model combined with detailed chemical kinetics, including 43 chemical species and 173 elementary reactions. In calculations, the effects of initial temperature, EGR ratios on ignition, and combustion were examined. The results indicated EGR combined with intake preheating can favorably reduced NOx and THC emissions simultaneously. This can be explained by the fact that combustion mechanism is changed from flame propagation to HCCl like combustion.

Natural gas pre-mixture is ignited by a small amount of pilot fuel in the dual fuel engine. In this paper, numerical studies were carried out to investigate the combustion and exhaust gas emissions formation process of this engine type by using a multi dimensional model combined with the detailed chemical kinetics including 57 chemical species and 290 elementary reactions. In calculation, the effect of the pre-mixture concentration on combustion was examined. The result indicated that the increased concentration of natural gas could improve the burning fraction and THC, CO emissions due to the increased pre-mixture consumption rate and the cylinders gas temperature.

The necessity of the reduction of the lubricating oil consumption of diesel engines has been increasing its importance to reduce the negative effect of exhausted oil on after treatment devices for exhausted gas. The final purpose of the studies is clarifying the mechanism of the oil consumption and developing the method of its estimation. For the basic study, the mechanism of oil film generation on the piston skirt could be explained by hydrodynamic lubrication in our first and second reports [1, 2]. In this paper, the piston skirt was calculated using the measured piston motion to clarify the effect of the piston motion to the piston skirt oil film behavior.

Clarifying the mechanism of the oil consumption of engines is necessary for developing its estimation method. Oil moves upwards on the piston to the combustion chamber through ring sliding surfaces, ring backs and ring gaps. The mechanisms of oil upwards transport through the ring gaps are hardly analyzed. In this report, oil pressure just under the oil ring was successfully measured by newly developed method to clarify the oil transport mechanism at the ring gap. It was showed that the generated oil pressure pushed up the oil at the ring gap.

The requirement for the reduction of lubricating oil consumption of diesel engines has become increasingly important in reducing the effect of exhausted oil on after treatment devices for exhaust gas. In our first report, findings indicated that piston skirt length affected oil consumption, and they clearly showed that the oil film on the piston skirt should be considered in the calculation for oil consumption. In this report, the mechanism of oil film generation on the piston skirt is investigated. The oil film on the piston skirt is calculated and the effect of piston motion on the oil film region is clarified, i.e., considering the piston rotation around the top of the piston skirt at the anti-thrust side is important for the calculation of the oil film region.

The authors have previously proposed a plume ignition and combustion concept (i.e., PCC combustion), in which a hydrogen fuel is directly injected to the combustion chamber in the latter half of compression stroke and forms a richer mixture plume. By combusting the plume, both cooling losses and NOx formation are reduced. In this study, thermal efficiency was substantially improved and NOx formation was reduced with PCC combustion by optimizing such characteristics as direction and diameter of the jets in combination with combustion of lean mixture. Output power declined due to the lean mixture, however, was recovered by supercharging while keeping NOx emissions at the same level. Thermal efficiency was further improved by slightly re-optimizing the jet conditions.

In our previous reports, we proposed a new focusing engine with high thermal efficiency based on relatively-silent high compression and nearly-complete air-insulation effect, which employs pulsed multi-jets of gas collided around chamber center. Local compression level due to the gas jets colliding around chamber center before reaction can be varied from zero to 100MPa and 3000K, by changing the number of jets and intake pressure. Relatively-silent high compression is possible, because region around chamber wall is at pressure level of traditional engines. This is suitable for various usages of automobiles, aerocrafts, and rockets, and also for various fuels including hydrogen, because high compression around chamber center leads to stable auto-ignition and potential of low NOx at very lean burning operation. We developed two types of focusing compression engines, without and with piston. For the new engine without piston, we obtained nearly-complete air-insulation and high thrust.

A new engine concept based on pulsed supermulti-jets colliding at a small area around the chamber center was proposed in our previous research. It was expected to provide noiseless high compression ratio and nearly-complete air-insulation on chamber walls, leading to high thermal efficiency. In the previous reports, three-dimensional computations for the unsteady compressible Navier-Stokes equation were conducted, which were qualitative because of using regular grid method. This time, we develop a new numerical code in order to quantitatively simulate the compression level caused by the jets colliding with pulse. It is achieved by applying a staggered grid method to improve conservatibity of physical quantities at very high compression in combustion phenomena. Computations at a simple condition were fairly agreed with a theoretical value. Computational results obtained for a complex geometry of an engine by the new code had less error than one with previous codes.

In recent years, a new type of engine (Fugine) based on the colliding of pulsed supermulti-jets was proposed by us, which indicates the potential for attaining very high thermal efficiencies and also less combustion noise. A prototype engine with eight nozzles for injecting octagonal pulsed supermulti-jets, which was developed with a low-cost gasoline injector and a double piston system, showed high thermal efficiency comparable to that of diesel engines and also less combustion noise comparable to that of traditional spark-ignition gasoline engines. Another type of prototype piston-less engine having fourteen bioctagonal nozzles was also developed and test results confirmed the occurrence of combustion, albeit it was unstable. In this work, time histories of pressure were measured in the combustion chamber of the piston-less prototype engine under a cold flow condition without combustion in order to examine the compression level obtained with the colliding supermulti-jets.

A new engine concept (Fugine) based on colliding pulsed supermulti-jets was proposed in recent years, which is expected to provide high thermal efficiencies over 50% and less combustion noise. Theoretical analyses indicate a high potential for thermal efficiency over 60%. Three types of prototype engines have been developed. The first prototype engine based only on the colliding of pulsed supermulti-jets with fourteen nozzles has no piston compression, while the second type equipped with a low-cost gasoline injector in the suction port has a double piston system and eight jet nozzles. Combustion experiments conducted on the second prototype gasoline engine show high thermal efficiency similar to that of traditional diesel engines and lower combustion noise comparable to that of traditional spark-ignition gasoline engines.

Three-way catalyst (TWC) converters can purify harmful substances, such as carbon monoxide, nitrogen oxides, and hydrocarbons, from the exhaust gases of gasoline engines. However, large amounts of these substances may be emitted before the TWC reaches its light-off temperature during cold starts, and its performance may be impaired by thermal deterioration during high-load driving. In this work, a simulation model was developed using axisuite commercial software by Exothermia S.A to predict the light-off conversion performance of Pd/CeO2-ZrO2-Al2O3 catalysts with different degrees of thermal deterioration. The model considered detailed surface reactions and the main factor of the deterioration mechanism. In the detailed reaction mechanism, adsorption, desorption, and surface reactions of each gas species at active sites of the platinum group metal (PGM) particles were considered based on the Langmuir-Hinshelwood mechanism.

An inexpensive, lightweight, and relatively quiet engine reactor that has the potential to achieve thermal efficiency over 50% for small engines was proposed in our previous reports, which is achieved with colliding supermulti-jets that create air insulation to encase burned gas around the chamber center, avoiding contact with the chamber walls and piston surfaces. The colliding of pulse jets can maintain high pressure ratio for various air-fuel ratios, whereas traditional homogeneous compression engines due to piston cannot get high pressure ratio at stoichiometric condition. Emphasis is also placed on the fact that higher compression in this engine results in less combustion noise because of encasing effect. Here, a small prototype engine having supermulti-jets colliding with pulse and strongly-asymmetric double-piston system is examined by using computational experiments. Pulse can be generated by the double piston system of a short stroke of about 40mm.

This study examines the effects of ethanol content on engine performances and the knock characteristics in spark ignition gasoline engine under various compression ratio conditions by cylinder pressure analysis, visualization and numerical simulation. The results confirm that increasing the ethanol content provides for greater engine torque and thermal efficiency as a result of the improvement of knock tolerance. It was also confirmed that increasing the compression ratio together with increasing ethanol content is effective to overcome the shortcomings of poor fuel economy caused by the low calorific value of ethanol. Further, the results of one dimensional flame propagation simulation show that ethanol content increase laminar burning velocity. Moreover, the results of visualization by using a bore scope demonstrate that ethanol affects the increase of initial flame propagation speed and thus helps suppress knock.

Pre-chamber (PC) natural gas and hydrogen (CH4-H2) combustion can improve thermal efficiency and greenhouse gas emissions from decarbonized stationary engines. However, the engine efficiency is worsened by prolonged combustion duration due to PC jet velocity extinction. This work investigates the impact of cylindrical PC internal shapes to increase its jet velocity and shorten combustion duration. A rapid compression and expansion machine (RCEM) is used to investigate the combustion characteristics of premixed CH4 gas. The combustion images are recorded using a high-speed camera of 10,000 fps. The experiments are conducted using two types of long PC shapes with diameters φ=4 mm (hereafter, longφ4) and 5 mm (hereafter, long φ5), and their combustions are compared against a short PC shape (φ=12 mm). For all designs of the PC shapes, the PC holes are 6 with 2 mm in diameter.

In our previous papers, a new concept of a compressive combustion engine (Fugine) was proposed based on the collision of pulsed supermulti-jets, which can enclose the burned gas around the chamber center leading to an air-insulation effect and also a lower exhaust gas temperature due to high single-point compression. In order to examine the compression level and air-insulation effect as basic data for application to automobiles, aircraft, and rockets, a prototype engine based on the concept, i.e., a piston-less prototype engine with collision of bi-octagonal pulsed multi-jets from fourteen nozzles, was developed. Some combustion results [Naitoh et al. SAE paper, 2016] were recently reported. However, there was only one measurement of wall temperature and pressure in the previous report. Thus, in this paper, more experimental data for pressures and temperatures on chamber walls and exhaust temperatures, are presented for the prototype engine.

Much effort has been devoted to studies on auto-ignition engines of gasoline including homogeneous-charge combustion ignition engines over 30 years, which will lead to lower exhaust energy loss due to high-compression ratio and less dissipation loss due to throttle-less device. However, the big problem underlying gasoline auto-ignition is knocking phenomenon leading to strong noise and vibration. In order to overcome this problem, we propose the principle of colliding pulsed supermulti-jets. In a prototype engine developed by us, octagonal pulsed supermulti-jets collide and compress the air around the center point of combustion chamber, which leads to a hot spot area far from chamber walls. After generating the hot spot area, the mechanical compression of an asymmetric double piston unit is added in four-stroke operation, which brings auto-ignition of gasoline.

In this study, we selected four unregulated emissions species, formaldehyde, benzene, 1,3-butadiene and benzo[a]pyrene to research the emission characteristics of these unregulated components experimentally. The engine used was a water-cooled, 8-liter, 6-cylinder, 4-stroke-cycle, turbocharged DI diesel engine with a common rail fuel injection system manufactured for the use of medium-duty trucks, and the fuel used was JIS second-class light gas oil, which is commercially available as diesel fuel. The results of experiments indicate as follows: formaldehyde tends to be emitted under the low load condition, while 1,3-butadiene is emitted at the low engine speed. This is believed to be because 1,3-butadiene decomposes in a short time, and the exhaust gas stays much longer in a cylinder under the low speed condition than under the high engine speed one. Benzene is emitted under the low load condition, as it is easily oxidized in high temperature.

Experimental and numerical studies on PAHs (Polycyclic Aromatic Hydrocarbons) and PM (Particulate Matters) formed in the fuel rich mixture have been conducted. In the experiment, neat n-heptane and n-heptane with benzene 25 % by weight were chosen as test fuels. In-cylinder gases produced by the fuel-rich HCCI (Homogeneous Charge Compression Ignition) combustion were directly sampled and analyzed by the use of GC/MS (Gas Chromatograph/Mass Spectro- metry), and PM emission was also measured by PM sampling system to reveal characteristics of PM formation. Numerical study has been also carried out using a zero dimensional combustion model combined with detailed chemistry. Furthermore, simple surface growth of soot particles was integrated into a detailed chemical kinetic model, and validated with the experimental data.

Experimental and numerical studies are conducted on the formation of soot and Polycyclic Aromatic Hydrocarbons (PAHs), regarded as precursors of soot, during the combustion of fuel-rich homogeneous n-heptane mixtures. In-cylinder gases are sampled directly through a high-speed solenoid valve in engine tests, to be analyzed by GC/MS for qualifying PAHs. Smoke concentration is also measured. A numerical study is carried out by using a zero-dimensional model combined with detailed chemical kinetics. The experiments and computations show that PAHs can be predicted qualitatively by means of the present kinetic model.