Search Results

A model which converts flame arrival times at a head gasket ionization probe, used in a spark-ignition engine, into flame contours has been developed. The head gasket was manufactured at MIT using printed circuit board techniques. It has eight electrodes symmetrically spaced around the circumference (top of cylinder liner) and it replaces the conventional head gasket. The model is based on engine flame propagation rate data taken from the literature. Data from optical studies of S.I. engine combustion or studies utilizing optical fiber or ionization probe diagnostics were analyzed in terms of the apparent flame speed and the entrainment speed (flame speed relative to the fluid ahead of the flame). This gives a scaling relationship between the flame speed and the mass fraction burned which is generic and independent of the chamber shape.

A complete one-dimensional mixed lubrication model has been developed to predict oil film thickness and friction of the piston ring-pack. An average flow model and a roughness contact model are used to consider the effects of surface roughness on both hydrodynamic and boundary lubrication. Effects of shear-thinning and liner temperature on lubricant viscosity are included. An inlet condition is applied by considering the unsteady wetting location at the leading edge of the ring. A ‘film non-separation’ exit condition is proposed to replace Reynolds exit condition when the oil squeezing becomes dominant. Three lubrication modes are considered in the model, namely, pure hydrodynamic, mixed, and pure boundary lubrication. All of these considerations are crucial for studying the oil transport, asperity contact, and friction especially in the top dead center (TDC) region where the oil control ring cannot reach.

Difficulties in the starting and operation of diesel engines at low temperatures are an important consideration in their design and operation, and in selection of the fuels for their use. Improvements in operation have been achieved primarily through external components of the engine and associated subsystems. A Rapid Compression Machine (RCM) has been modified to operate over a wide range of temperatures (−20°C to 100°C). It is used to isolate the combustion chamber in an environment in which all significant parameters are carefully defined and monitored. The influence of temperature and cetane number on the ignition and combustion processes are analyzed. Examination of the combustion characteristics show that temperature is by far the most influential factor affecting both ignition delay and heat release profiles. Cetane number (ASTM D-613) is not found to be a strong indicator of ignition delay for the conditions investigated.

This paper describes the use of a modified quasi-dimensional spark-ignition engine simulation code to predict the extent of cycle-to-cycle variations in combustion. The modifications primarily relate to the combustion model and include the following: 1. A flame kernel model was developed and implemented to avoid choosing the initial flame size and temperature arbitrarily. 2. Instead of the usual assumption of the flame being spherical, ellipsoidal flame shapes are permitted in the model when the gas velocity in the vicinity of the spark plug during kernel development is high. Changes in flame shape influence the flame front area and the interaction of the enflamed volume with the combustion chamber walls. 3. The flame center shifts due to convection by the gas flow in the cylinder. This influences the flame front area through the interaction between the enflamed volume and the combustion chamber walls. 4. Turbulence intensity is not uniform in cylinder, and varies cycle-to-cycle.

A conventional coil ignition system and two breakdown ignition systems with different electrode configurations were compared in M.I.T.'s transparent square piston engine. The purpose was to gain a deeper understanding of how the breakdown and glow discharge phases affect flame development and engine performance. The engine was operated with a standard intake valve and with a shrouded intake valve to vary the characteristic burning rate of the engine. Cylinder pressure data were used to characterize the ignition-system performance. A newly developed schlieren system which provides two orthogonal views of the developing flame was used to define the initial flame growth process. The study shows that ignition systems with higher breakdown energy achieve a faster flame growth during the first 0.5 ms after spark onset for all conditions studied.

An adaptive air/fuel ratio controller for SI engine throttle transient was developed. The scheme is based on an event- based, single- parameter fuel dynamics model. A least- square- error algorithm with an active forgetting factor was used for parameter identifications. A one- step- look- ahead controller was designed to maintain the desired air/fuel ratio by canceling the fuel dynamics with the controller setting updated adaptively according to the identified parameters. When implemented on a Ford Ztech engine and tested under a set of throttle- transient operations, the adaptive controller learned quickly and performed well.

Engine oil consumption is an important source of hydrocarbon and particulate emissions in automotive engines. Oil evaporating from the piston-ring-liner system is believed to contribute significantly to total oil consumption, especially during severe operating conditions. This paper presents an extensive experimental and theoretical study on the contribution of oil evaporation to total oil consumption at different steady state speed and load conditions. A sulfur tracer method was used to measure the dependence of oil consumption on coolant outlet temperature, oil volatility, and operating speed and load in a production spark ignition engine. Liquid oil distribution on the piston was studied using a one-point Laser-Induced-Fluorescence (LIF) technique. In addition, important in-cylinder variables for oil evaporation, such as liner temperature and cylinder pressure, were measured. A multi-species cylinder liner oil evaporation model was developed to interpret the oil consumption data.

A spark-ignition engine friction model developed by Patton et al. in the late 1980s was evaluated against current engine friction data, and improved. The model, which was based on a combination of fundamental scaling laws and empirical results, includes predictions of rubbing losses from the crankshaft, reciprocating, and valvetrain components, auxiliary losses from engine accessories, and pumping losses from the intake and exhaust systems. These predictions were based on engine friction data collected between 1980 and 1988. Some of the terms are derived from lubrication theory. Other terms were derived empirically from measurements of individual friction components from engine teardown experiments. Recent engine developments (e.g., improved oils, surface finish on piston liners, valve train mechanisms) suggested that the model needed updating.

This paper provides an overview of spark-ignition engine unburned hydrocarbon emissions mechanisms, and then uses this framework to relate measured engine-out hydrocarbon emission levels to the processes within the engine from which they result. Typically, spark-ignition engine-out HC levels are 1.5 to 2 percent of the gasoline fuel flow into the engine; about half this amount is unburned fuel and half is partially reacted fuel components. The different mechanisms by which hydrocarbons in the gasoline escape burning during the normal engine combustion process are described and approximately quantified. The in-cylinder oxidation of these HC during the expansion and exhaust processes, the fraction which exit the cylinder, and the fraction oxidized in the exhaust port and manifold are also estimated.

An analysis method for characterizing fuel behavior during spark-ignition engine starting has been developed and applied to several sets of start-up data. The data sets were acquired from modern production vehicles during room temperature engine start-up. Two different engines, two control schemes, and two engine temperatures (cold and hot) were investigated. A cycle-by-cycle mass balance for the fuel was used to compare the amount of fuel injected with the amount burned or exhausted as unburned hydrocarbons. The difference was measured as “fuel unaccounted for”. The calculation for the amount of fuel burned used an energy release analysis of the cylinder pressure data. The results include an overview of starting behavior and a fuel accounting for each data set Overall, starting occurred quickly with combustion quality, manifold pressure, and engine speed beginning to stabilize by the seventh cycle, on average.

The direct injection spark-ignition engine is the only internal combustion engine with the potential to equal the efficiency of the diesel and to tolerate a wide range of fuel types and fuel qualities without deterioration of performance. However, this engine has low combustion efficiency and excessive hydrocarbon emissions when operating at light load. In this paper, potential sources of hydrocarbon emissions during light load operation are postulated and analyzed. The placement of fuel away from the primary combustion process in conjunction with a lack of secondary burnup are isolated as important hydrocarbon emissions mechanisms. Analyses show that increasing cylinder gas temperatures can improve secondary burnup of fuel which would reduce hydrocarbon emissions. Practical means to achieve this include higher compression ratio and use of ceramic parts in the combustion chamber.

The NOx emissions during the crank-start and cold fast-idle phases of a GDI engine are analyzed in detail. The NOx emissions of the first 3 firing cycles are studied under a wide set of parameters including the mass of fuel injected, start of injection, and ignition timing. The results show a strong dependence of the NOx emissions with injection timing; they are significantly reduced as the mixture is stratified. The impact of different valve timings on crank-start NOx emissions was analyzed. Late intake and early exhaust timings show similar potential for NOx reduction; 26-30% lower than the baseline. The combined strategy, resulting in a large symmetric negative valve overlap, shows the greatest reduction; 59% lower than the baseline. The cold fast-idle NOx emissions were studied under different equivalence ratios, injection strategies, combustion phasing, and valve timings. Slightly lean air-fuel mixtures result in a significant reduction of NOx.

Engine oil consumption is recognized to be a significant source of pollutant emissions. Unburned or partially burned oil in the exhaust gases contributes directly to hydrocarbon and particulate emissions. In addition, chemical compounds present in oil additives poison catalytic converters and reduce their conversion efficiency. Oil consumption can increase significantly during critical non-steady operating conditions. This study analyzes the oil consumption behavior during ramp transients in load by combining oil consumption measurements, in-cylinder measurements, and computer-based modeling. A sulfur based oil consumption method was used to measure real-time oil consumption during ramp transients in load at constant speed in a production spark ignition engine. Additionally in-cylinder liquid oil behavior along the piston was studied using a one-point Laser-Induced-Fluorescence (LIF) technique.

The flow and combustion processes of a three-valve, stratified charge engine with small prechamber are examined for exhaust emissions. The exhaust emissions from a single-cylinder version of this engine are shown to depend on the internal flow processes as well as mixture supply stoichiometry. A theoretically-based simulation model of the engine flow and combustion processes is described. Model predictions are compared with time-resolved prechamber air-fuel ratio measurements made during intake and compression strokes. These comparisons are used to illustrate and describe the complex flow phenomena which take place in this engine. The combustion process is then examined with the aid of calculations using the simulation model. The complexity of the combustion process is illustrated by showing that, in addition to burned gas temperatures, the cylinder and prechamber burned gas air-fuel ratios change with time.

The loss mechanisms associated with engine downsizing, boosting and compression ratio change are assessed. Of interest are the extents of friction loss, pumping loss, and crevice loss. The latter does not scale proportionally with engine size. These losses are deconstructed via a cycle simulation model which encompasses a friction model and a crevice loss model for engine displacement of 300 to 500 cc per cylinder. Boost pressure is adjusted to yield constant torque. The compression ratio is varied from 8 to 20. Under part load, moderate speed condition (1600 rpm; 13.4 Nm/cylinder brake torque), the pumping work reduces significantly with downsizing while the work loss associated with the crevice volume increases. At full load (1600 rpm; 43.6 Nm/cylinder brake torque), the pumping work is less significant. The crevice loss (normalized to the fuel energy) is essentially the same as in the part load case. The sensitivities of the respective loss terms to downsizing are reported.

Spark-ignition engine knock was characterized in terms of when during the engine cycle and combustion process knock occurred and its magnitude or intensity. Cylinder pressure data from a large number of successive individual cycles were generated from a single-cylinder engine of hemispherical chamber design over a range of operating conditions where knock occurred in some or all of these cycles. Mean values and distributions of following parameters were quantified: knock occurrence crank angle, knock intensity, combustion rate and the end-gas thermodynamic state. These parameters were determined from the cylinder pressure data on an individual cycle basis using a mass-burn-rate analysis. The effects of engine operating variables on these parameters were studied, and correlations between these parameters were examined.

A dynamometer-mounted four-cylinder Saturn engine was used to accumulate combustion chamber deposits (CCD), using an additized fuel. During each deposit accumulation test, the HC emissions were continuously measured. The deposit thickness at the center of the piston was measured at the beginning of each day. After the 50 and 35-hour tests, HC emissions were measured with isooctane, benzene, toluene, and xylene, with the deposited engine, and again after the deposits had been cleaned from the engine. The HC emissions showed a rapid rise in the first 10 to 15 hours and stabilization after about 25 hours of deposit accumulation. The HC increase due to CCD accumulation accounted for 10 to 20% of the total engine-out HC emissions from the deposit build-up fuel and 10 to 30% from benzene, isooctane, toluene, and xylene, making CCDs a significant HC emissions source from this engine. The HC emissions stabilized long before the deposit thickness.

An experimental study was conducted on a direct-injection stratified-charge (DISC) engine incorporating a combustion process similar to the Texaco Controlled Combustion System and operated with gasoline. Analysis of the injected fuel flow and the heat release showed that the combustion process was characterized by three distinct phases: fuel injection and distribution around the piston bowl, flame propagation through the stratified fuel-air mixture, and mixing-controlled burn-out with the heat-release rate proportional to the amount of unburned fuel in the combustion chamber. This characterization was consistent with previous visualization studies conducted on rapid-compression machines with similar configurations. Experiments with varied injection timing, spark plug location, and spark timing showed that the combustion timing relative to injection was critical to the hydrocarbon emissions from the engine.

As part of ongoing research on hydrogen-enhanced lean burn SI engines, this paper details an experimental combustion system optimization program. Experiments focused on three key areas: the ignition system, in-cylinder charge motion produced by changes in the inlet ports, and uniformity of fuel-air mixture preparation. Hydrogen enhancement is obtained with a H2, CO, N2 mixture produced by a fuel reformer such as the plasmatron. The ignition system tests compared a standard inductive coil scheme against high-energy discharge systems. Charge motion experiments focused on the impact of different flow and turbulence patterns generated within the cylinder by restrictor plates at the intake port entrance, as well as novel inlet flow modification cones. The in-cylinder fluid motion generated by each configuration was characterized using swirl and tumble flow benches. Mixture preparation tests compared a standard single-hole pintle port fuel injector against a fine atomizing 12-hole injector.

A research program designed to measure the contribution from fuel absorption in the thin layer of oil, lubricating the cylinder liner, to the total and speciated HC emissions from a spark ignition engine has been performed. The logic of the experiment design was to test the oil layer mechanism via variations in the oil layer thickness (through the lubricant formulations), solubility of the fuel components in the lubricants, and variations in the crankcase gas phase HC concentration (through crankcase purging). A set of preliminary experiments were carried out to determine the solubility and diffusivity of the fuel components in the individual lubricants. Engine tests showed similar HC emissions among the tested lubricants. No consistent increase was observed with oil viscosity (oil film thickness), contrary to what would be expected if fuel-oil absorption was contributing significantly to engine-out HC. Similarly, no effect of crankcase purging could be observed.