Search Results

It has been proposed that an automated remote color inspection of automobile body panels is possible with a reasonably precise color measurement. This paper outlines a test of a new 3D color measurement technology as applied to this task and presents the results of the first test. A camera is set up several feet away from a car body; a 3D orientation measuring system takes both 3D and color data from the car. The raw data is presented as a set of 3D graphs; the geometry-corrected data is also provided. Statistical analysis is presented to indicate system precision.

The Rand Cam engine is a novel design which avoids the use of pistons in favor of a cavity of varying size and shape. A set of vanes protrudes from a rotor into a circular trough in a stator. The vanes seal to the walls and base of the trough, which is of varying depth, and progress around the trough with rotation of the rotor. These vanes therefore pass through the rotor and are constrained to move parallel to the rotational axis. Intake and exhaust processes occur through ports in the stator wall which are revealed by the passing vanes. Advantages of the basic design include an absence of valves, reduction in reciprocating masses, presence of an integral flywheel in the rotor and strong fluid movement akin a swirl induced by the relative velocity between the rotor and stator.

The commercially available RNG k-e turbulence model with enhanced wall treatment found in Fluent 6.1 was used to solve the flow over a V-22 Osprey wing equipped with blowing slots. The solutions were then compared to experimental data. Good correlation between the computational and experimental data was found. Download on the wing from the rotors while the aircraft is operating in vertical take-off and landing mode was found to be reduced by the blowing slots.

Previous studies have shown that using blowing slots can reduce the effects of the rotor downwash on the main wing of a tilt-rotor aircraft, particularly the V-22 Osprey. The current study investigates the placement and air velocity of the leading edge blowing slot for optimization of the download reduction. The realizable turbulent kinetic energy - rate of dissipation (rke) numerical model available in Fluent 6.2.12 was used to model the flow involved under the rotors and the subsequent downwash around the main wing. It was found that the leading edge blowing slot is most beneficial when it is placed just upwind of the separation point without blowing slots. In the current investigation the optimal configuration is found between 0 percent and 1 percent of the chord length.

The development of a standardized roll-on, roll-off (RoRo) sensor pallet system for a C-130 aircraft was conceived by the National Guard and the Counter Narco-Terrorism Technology Development Office to assist in counterdrug reconnaissance activities within the United States and surveillance and reconnaissance missions worldwide. West Virginia University was contracted to perform the design and development of this system because of their innovative design ideas. Before development, the design parameters were established by these two DoD agencies, their mission requirements and by the limitations of the C-130 aircraft. These limitations include using Commercial off the Shelf (COTS) and Government off the Shelf (GOTS) items when developing the system that must be universal on all C-130 aircrafts variants B thru H. Further design criteria are by the limitations of the C-130 aircraft and its existing mission requirements.

Enhancing the capabilities of established airframes to meet expanded mission requirements is preferential to the design of specialized aircraft. The high cost associated with the research and development of a specialized aircraft platform has shifted the concentration towards the modification of existing aircraft to support multiple C4ISR missions. The recently developed Oculus sensor deployment system is one such example of this trend, providing a fully integrated aerial visual enhancement platform with multi-mission capabilities. This paper provides a short survey of the Oculus sensor pallet system and overviews some of the multiple guidelines used which ensure that various remote sensing technologies may be securely and simultaneously deployed.

The downwash of the prop-rotor blades of the Bell/Boeing V-22 “Osprey” in hover mode creates an undesirable negative lift on the wing of the aircraft. This downforce can be reduced through a number of methods. Neglecting all other effects, such as power requirements, this research investigated the feasibility of using circulation control, through blowing slots on the leading and trailing edge of the airfoil to reduce the wake profile under the wing. A model was built at West Virginia University (WVU) and tested in a Closed Loop Wind Tunnel. The airfoil was placed normal to the airflow using the tunnel air to simulate the vertical component of the downwash experienced in hover mode. The standard hover mode flap angle of 67 degrees was used throughout the testing covered in this paper. All of these tests were conducted at a free stream velocity of 59 fps, and the baseline downforce on the model was measured to be 5.45 lbs.

During structural engineering design two of the most overlooked design facets of a finished product is understanding the behavior characteristics of how the product will react when resonated at its natural frequencies and actually defining and understanding the overall vibration profile responsible for the excitation of the structure. A C-130 mechanical arm/pod system has been developed to accommodate 1,000-pounds of sensor payload deployable in flight from a C-130 Hercules military aircraft (variants B thru J). The mechanical arm/pod system will be subjected to a profile of vibration from numerous sources during deployment and while in the final operating position. A general vibration profile for the mechanical arm/pod will be compiled from the plane’s four T-56-A-15 turboprop engines, the atmospheric turbulence and random gust loads.

The development of a mathematical model of StillerSmith Mechanism for the application of a 4-cylinder plunger pump system is presented. The magnitude and direction of the internal dynamic load are obtained by solving a set of equations using the overall geometric parameters, prescribed motions, inertia distribution, and applied torques on the system. The simulation presented here yields the history of the internal loads, which are then normalized with respect to the required peak output load on the plungers, through an entire rotary cycle. The approach allows for the development of further design criteria through parametric sensitivity studies.

Project Oculus is an in-flight deployable mechanical arm/pod system that will accommodate 500 pounds of sensor payload, developed for a C-130 military aircraft. The system is designed for use in counter narco-terrorism and surveillance applications by the Department of Defense and the National Guard [1]. A prototype of the system has been built and is in the testing/analysis phase. The purpose of this study was to analyze the actual stresses and strains in the critical areas found using previous Finite Element (FE) simulations and to ensure that acceptable safety requirements have been met. The system components tested will be redesigned, tested, and reconstructed in the case of unacceptable safety factors or if more reliable methods can be implemented. The system was built to be deployed and retracted in flight, to avoid causing any problems in take off and landing.

In this analysis the structural integrity of the rotational system of a standardized roll-on, roll-off sensor pallet system was authenticated. The driving force behind this analysis was to ensure the structural integrity of the system and to locate the areas with optimization potential. This process will ideally lead to the weight reduction of individual components thereby allowing for the transportation of greater cargo during flight. Scaling down of these excessive areas will also allow for a reduced production cost and an increase in efficiency of the system. The study was comprised of the failure susceptibility of the individual components of the system. The major results include the optimization potential of individual components, as well as strategically rating and categorizing the failure capability of the components.

In this paper, a new method for the hydro-dynamic analysis of a sliding cylinder in a fully lubricated parallel track is presented. The method is an extension of Booker's “Mobility Method” (developed for cylindrical journal bearings) to the case of sliding cylinders, in which the clearance between the track and the cylinder, the viscosity of the lubricant, the radius and length of the pin, the sliding velocity and the applied transverse load determine the hydrodynamic behavior of the cylinder. In the Rand Cam™ Engine [1]*, the axicycloidal motion of vanes is driven by a rotor and a cylindrical cam, and one of the alternative designs to provide this function is based on a cylindrical pin sliding within a track which follows the profile of the motion of the main cams of the engine. This function is very important for the engine, since it separates the load bearing function from the sealing function left to the apex-like seals.

A comprehensive review of low-heat rejection engine concepts is presented. Areas examined include the materials being considered for these engines; fuels including coal; the effects of high temperature upon emissions; tribology with ceramics; exhaust heat utilization systems; and applications of these engines. Inconsistencies in the literature arc discussed.

Over the years, there have been different ways to reduce glare from mirrors for drivers - dimmable electrochromic mirrors being the latest option. These mirrors often have a limited lifespan when exposed to the environment, and are often costly to replace. It is now feasible to have a rear-view mirror assembly whose reflectance is mechanically adjustable. This is accomplished by using polarized light and a pair of specially constructed polarizers. These polarizers attenuate light by sliding past one another in a linear fashion, as opposed to rotating with respect to one another to cross their transmission axes. This is ideal for rear-view mirrors whose shapes are often oblong and rotation of a polarizer is awkward. In the event of a power failure, these polarizing mirrors are still capable of dimming. They can be made to function well in both hot and cold environments, have a long lifespan, and are inexpensive when compared to electrochromic mirrors.

The basic design of a purely rotary motion engine has potentially many advantages over the conventional piston-crank internal combustion engine. Although only one rotary engine has been successfully placed into production, rotary mechanisms still show promise in the market place. A comprehensive review of rotary engine concepts is presented with an emphasis placed on the last 30 years. Suggestions are made as to where research concentrations should be placed to improve the progress of a rotary engine.

Analysis of two types of bearings has been performed for the rotor shaft of the Rand Cam™ engine. Rolling element bearings and a combination of journal and thrust bearings for selected engine configurations have been considered. The engine configurations consist of four, five, six, seven, and eight vanes. The bearing geometry and orientation was also addressed. This analysis is crucial due to the potentially large axial loading on the bearings and the need for the bearing arrangement to be compact and reliable. An emphasis was placed on the combination of fluctuating axial and radial loads and the resulting effect upon the bearings. Tapered roller bearings were found to be effective. However, a combination of journal and thrust bearings is a more compact bearing arrangement for this application. The eight vane configuration is the most desirable configuration based upon the bearing analysis.

At flight levels above the ceiling of 10,000 feet, during the operational phase of a sensor deployment system for a C-130 aircraft, it becomes necessary to seal the cargo hold to maintain pressure for the safety and comfort of the crew and operators. In order for the sensor deployment System to have full mission support capabilities for DoD reconnaissance needs, a system must be designed where-by the cargo area may be sealed once the system has been deployed. Currently, with the sensor pod in position, the ramp can be closed to within a few inches of the locked position. The door in this position, for stability during flight, must be locked and structurally supported to maintain the aircrafts design requirements. This presents the first of a series of issues that must be examined for the success of the final design. To seal the remaining area, an expanding “bladder-seal” has been developed.

The Rand-Cam engine is a positive displacement machine, operating on a four stroke cycle, which consists of a rotor with multiple axial vanes forming combustion chambers as the rotor and vanes rotate in a cam shaped housing. The cam housing, consisting of two “half-housings” or stators, contains a toroidal trough of varying depth machined into each stator. The two stators are phased so that the shallowest point on one trough corresponds to the deepest on the other. A set of six vanes, able to move axially through machined holes in the rotor, traverses the troughs creating six captured zones per side. These zones vary in volume with rotor rotation. Since each trough has two deep sections and two shallow sections with ramps in between, full four stroke operation is obtained between each pair of vanes in each trough, corresponding to twelve power “strokes” per revolution.

New high-tech materials which are anticipated to revolutionize the internal combustion engine are being created everyday. However, their actual utilization in existing engines has encountered numerous stumbling blocks. High piston sidewall forces and thermal stresses are some of the problems of primary concern. The Stiller-Smith Engine should provide an environment more conducive to the use of some of these materials. Absent from the Stiller-Smith Engine is a crankshaft, and thus a very different motion is observed. Since all parts in the Stiller-Smith Engine move in either linear or rotary fashion it is simple to balance. Additionally the use of linear connecting rod bearings changes the location of the sidewall forces thus providing an isolated combustion chamber more tolerant to brittle materials and potential adiabatic designs. Presented herein is the development of this new engine environment, from conceptualization to an outline of present and future research.

The Stiller-Smith Mechanism provides a unique approach in the use of the rotational characteristics of the cross-slider link of the elliptic trammel. Establishment of the research need and a historical development of the design concept are presented complete with a detailed kinematic analysis. Successful incorporation of the new mechanism is pictorially presented.