Search Results

A 10 KWe dual-mode space power system concept has been identified which is based on INEL's Small Externally-fueled Heat Pipe Thermionic Reactor (SEHPTR) concept. This power system will enhance user capabilities by providing reliable electric power and by providing two propulsion systems; electric power for an arc-jet electric propulsion system and direct thrust by heating hydrogen propellant inside the reactor. The low thrust electric thrusters allow efficient station keeping and long-term maneuvering. The direct thrust capability can provide tens of pounds of thrust at a specific impulse of around 730 seconds for maneuvers that must be performed more rapidly. The direct thrust allows the nuclear power system to move a payload from Low Earth Orbit (LEO) to Geosynchronous Earth Orbit (GEO) in less than one month using approximately half the propellant of a cryogenic chemical stage.

This SAE standard establishes the minimum construction and performance requirements for a combination cable consisting of 9 conductors and 2 twisted pairs for use on trucks, trailers, and dollies. The cable includes power, ground and 2 jacketed/unshielded twisted paired signal circuits. This standard will be used in conjunction with the SAEJ XXXX “13 Conductor Electrical Connector (Plug and Receptacle) between Towing Vehicle and Trailer”. The standard will also include the test procedures, design and performance requirements for the cable.

Most of current jet aircraft circulate fuel on the airframe to match heat loads with available heat sink. The demands for thermal management in wide range of air vehicle systems are growing rapidly along with the increased mission power, vehicle survivability, flight speeds, and so on. With improved aircraft performance and growth of heat load created by Aircraft Mounted Accessory Drive (AMAD) system and hydraulic system, effectively removing the large amount of heat load on the aircraft is gaining crucial importance. Fuel is becoming heat transfer fluid of choice for aircraft thermal management since it offers improved heat transfer characteristics and offers fewer system penalties than air. In the scope of this paper, an AMESim model is built which includes airframe fuel and hydraulic systems with AMAD gearbox of a jet trainer aircraft. The integrated model will be evaluated for thermal performance.

Three-component Particle Image Velocimetry (3D PIV) is a fluid velocity measurement technique that has evolved from the laboratory to become a method appropriate for use in large-scale wind tunnel testing. An example application of 3D PIV in a wind tunnel test is described. The PIV technique was applied to characterize the wake of The Ground Transportation System (GTS) model developed for the Department of Energy (DOE) Heavy Vehicle Drag Reduction (HVDR) program. The test was performed in the Ames/Army 7×10 foot wind tunnel. The objective of the PIV measurements was to validate the HVDR computational fluid dynamics code. The PIV method and PIV system are described. Sample truck wake data with and without boattail attachments are shown. 3D PIV system successfully captured the effects of the boattails on the truck wake.

A 500 hours endurance test was performed with a heavy-duty engine (Euro IV); MAN type D 0836 LFL 51 equipped with a PM-Kat®. As fuel 100% biodiesel was used that met the European specification EN 14214. The 500 hours endurance test included both the European stationary and transient cycle (ESC and ETC) as well as longer stationary phases. During the test, regulated emissions (carbon monoxide, nitrogen oxides, hydrocarbons and particulate matter), the particle number distribution and the aldehydes emission were continuously measured. For comparison, tests with fossil diesel fuel were performed before and after the endurance test. During the endurance test, the engine was failure-free for 500 hours with the biogenic fuel. There were almost no differences in specific fuel consumption during the test, but the average exhaust gas temperature increased by about 15°C over the time. Emissions changed only slightly during the test.

Flight control technology for 8000 psi has emerged almost simultaneously with new fire-resistant hydraulic fluids, such as MIL-H-83282 and CTFE. A proliferation of industry recommendations has resulted in a wide variety of mechanisms for solving associated actuator design problems, including tighter clearances, special seals, finishes, materials, and many others. As there are few common agreements on the issues, an extensive three-phase test program was undertaken to attempt to corroborate some of these approaches or suggest others that may be better or more cost effective.

An 8000 psi test program was conducted to resolve conflicts and issues surrounding the use of CTFE and MIL-H-83282 fluid with vented and unvented actuator rod seals. Each of the four possible combinations had unique problems and each responded to appropriate corrections including new backup rings designed to operate with standard clearances. It was concluded that all combinations were viable within certain limits. Advantages and disadvantages of each configuration were identified and specific recommendations made for both dynamic and static seals within the context of existing military specifications.

Shortly after World War II, as aircraft became more sophisticated and power-assist, flight-control functions became a requirement, hydraulic system operating pressures rose from the 1000 psi level to the 3000 psi level found on most aircraft today. Since then, 4000 psi systems have been developed for the U.S. Air Force XB-70 and B-1 bombers and a number of European aircraft including the tornado multirole combat aircraft and the Concorde supersonic transport. The V-22 Osprey incorporates a 5000 psi hydraulic system. The power levels of military aircraft hydraulic systems have continued to rise. This is primarily due to higher aerodynamic loading, combined with the increased hydraulic functions and operations of each new aircraft. At the same time, aircraft structures and wings have been getting smaller and thinner as mission requirements expand. Thus, internal physical space available for plumbing and components continues to decrease.

Shortly after World War II, as aircraft became more sophisticated and power-assist, flight-control functions became a requirement, hydraulic system operating pressures rose from the 1000 psi level to the 3000 psi level found on most aircraft today. Since then, 4000 psi systems have been developed for the U.S. Air Force XB-70 and B-1 bombers and a number of European aircraft including the tornado multirole combat aircraft and the Concorde supersonic transport. The V-22 Osprey incorporates a 5000 psi hydraulic system. The power levels of military aircraft hydraulic systems have continued to rise. This is primarily due to higher aerodynamic loading, combined with the increased hydraulic functions and operations of each new aircraft. At the same time, aircraft structures and wings have been getting smaller and thinner as mission requirements expand. Thus, internal physical space available for plumbing and components continues to decrease.

This paper describes how airplane control surface rate limiting can enable a ‘cliff-like’ onset of Pilot-Induced Oscillation, (P.I.O.) and how the danger can be erased by implementation of Conditionally Enabled Phase Compensated Rate Limiters, (PCRLs), in the design of the airplane's flight control system. The application is particularly important for large airplanes where control surface actuator sizing and the associated hydraulic system volumetric flow rate capability cannot be generously over-sized without large weight and cost penalties. It is shown that the PCRL can remain inactive during normal airplane operations where RMS control commands are relatively small thus avoiding adverse control surface response effects that have hindered earlier PCRL acceptance.

A hydrogen economy is an increasingly popular solution to lower global carbon dioxide emissions. Previous research has been focused on the economic conditions necessary for hydrogen to be cost competitive, which tends to neglect the effectiveness of greenhouse gas mitigation for the very solutions proposed. The holistic carbon footprint assessment of hydrogen production, distribution, and utilization methods, otherwise known as “well-to-wheels” carbon intensity, is critical to ensure the new hydrogen strategies proposed are effective in reducing global carbon emissions. When looking at these total carbon intensities, however, there is no single clear consensus regarding the pathway forward. When comparing the two fundamental technologies of steam methane reforming and electrolysis, there are different scenarios where either technology has a “greener” outcome.

As mission length and the number and complexity of payload experiments increase, so does the probability of thermodegradation contingencies (e.g. fire, chemical release and/or smoke from overheated components or burning materials), which could affect mission success. When a thermodegradation event occurs on board a spacecraft, potentially hazardous levels of toxic gases could be released into the internal atmosphere. Experiences on board the Space Shuttle have clearly demonstrated the possibility of small thermodegradation events occurring during even relatively short missions. This paper will describe the Combustion Products Analyzer (CPA), which is being developed under the direction of the Toxicology Laboratory at Johnson Space Center to provide necessary data on air quality in the Shuttle following a thermodegradation incident.

Both humans and onboard radiosensitive systems (electronics, materials, payloads and experiments) are exposed to the deleterious effects of the harsh space radiations found in the space environment. The purpose of this paper is to present the space radiation environment extended to deep space based on environment models for the moon, Mars, Jupiter, and Saturn and compare these radiation environments with the earth's radiation environment, which is used as a comparative baseline. The space radiation environment consists of high-energy protons and electrons that are magnetically “trapped” in planetary bodies that have an intrinsic magnetic field; this is the case for earth, Jupiter, and Saturn (the moon and Mars do not have a magnetic field). For the earth this region is called the “Van Allen belts,” and models of both the trapped protons (AP-8 model) and electrons (AE-8 model) have been developed.

This paper presents the results of an investigation to improve design/analysis techniques for aircraft hydraulic systems. A design/analysis tool was developed by integrating control-surface commands and loads obtained from Aircraft Dynamic Simulator Software (ADSS) with an enhanced version of the HYdraulic TRansient ANalysis (HYTRAN) program. Control-surface commands and loads from an ADSS simulation of a selected maneuver were used as dynamic input to the HYTRAN program so that the hydraulic system response could be predicted throughout the maneuver. Predicted hydraulic system pressures and control-surface positions from the HYTRAN simulation of the maneuver were compared to flight-test data and were found to be in excellent agreement. The successful coalescence of the two independent software programs gives engineers a concurrent design/analysis tool that can be used to optimize hydraulic system designs during the very early stages of design.

The Shuttle orbiter currently uses hydrazine-powered APU’s for powering its hydraulic system pumps. To enhance vehicle safety and reliability, NASA is pursuing an APU upgrade where the hydrazine-powered turbine is replaced by an electric motor pump and battery power supply. This EAPU (Electric APU) upgrade presents several thermal control challenges, most notably the new requirement for moderate temperature control of high-power electronics at 132 °F (55.6 °C). This paper describes how the existing Water Spray Boiler (WSB), which currently cools the hydraulic fluid and APU lubrication oil, is being modified to provide EAPU thermal management.

This test method describes a procedure for determining the insoluble contamination level of the downstream side of filter elements. Results of this procedure are intended to be used only for evaluation of the effectiveness of various cleaning treatments, or cleanliness of element as received from manufacturers. The data obtained by this procedure do not necessarily indicate, qualitatively or quantitatively, the contamination which may be released by a filter element into a fluid during service use. Because of the wide variety of conditions which may exist in service applications, it is recommended that the user design and conduct his own particular service performance test. (See paragraph 10.1).

Considering the rising cost and diminished availability of 100-octane, low-lead (100 LL) aviation gasoline, owners of aircraft certified for 100 LL may be forced to find an alternative fuel in the near future. This study proposed a blend of 200-proof anhydrous ethanol ($1.70 per gallon) and automotive gasoline ($1.15 per gallon) as a replacement for aviation gasoline ($1.90 per gallon). The research program included materials compatibility tests, Cooperative Fuel Research (CFR) engine tests, static thrust tests, and a flight test to determine the feasibility of such a blend as a fuel for an unmodified aircraft engine. Throughout all tests, blends burned as well as aviation gasoline. The static thrust tests indicated that a blend of 35% ethanol/65% automotive gasoline yielded the maximum thrust output. The materials tests revealed metals to be unaffected by contact with the blend fuel. Fibrous growths were discovered in the blend and in the automotive gasoline samples.

The BSTCA (Battery Section Thermal Control Assembly) is a module of the Columbus MTFF (Man Tended Free Flyer). Electrical power required during eclipse periods, is made available from six nickel hydrogen batteries. A sophisticated multi-radiator configuration, with a hybrid heat pipe network, has evolved. Autonomous control of the assembly heat rejection capability has been achieved by a integrated network of LTHP's (Liquid Trap Heat Pipes) and CCHP's (Constant Conductance Heat Pipes) under the control of a conventional HCU (Heater Control Unit). The process of design selection and verification is discussed, for the BSTCA, with a detailed LTHP component presentation.

Hydrogen has difficulties in handling in a fuel cell vehicle, and has a fault with taking a big space there. The authors have proposed a hydrogen generation system using ammonia as a liquid fuel for fuel-cell electric vehicles. Ammonia has an advantage not to emit greenhouse effect gases because it does not contain a carbon atom. Hydrogen content of ammonia is 17.6 wt% and hydrogen quantity per unit mass is large. Ammonia can be easily dissociated to hydrogen and nitrogen by heating. Therefore, ammonia is an attractive hydrogen supply source for fuel cell vehicles. The ammonia hydrogen generation system of this study consists of a vaporizer, a heat exchanger and a cracking reactor with a separator. Ammonia is heated with the heat exchanger and sent to the cracking reactor, after it is evaporated through the vaporizer from the liquid ammonia. The ammonia is cracked to hydrogen and nitrogen with an appropriate catalyst.

The factors involved in the selection of a quick-disconnect are grouped into the following classifications for the purpose of discussion: (a) Functional considerations. (b) Weight considerations. (c) Environmental performance factors. (d) End fitting types. (e) Additional considerations.