Search Results

A 10 KWe dual-mode space power system concept has been identified which is based on INEL's Small Externally-fueled Heat Pipe Thermionic Reactor (SEHPTR) concept. This power system will enhance user capabilities by providing reliable electric power and by providing two propulsion systems; electric power for an arc-jet electric propulsion system and direct thrust by heating hydrogen propellant inside the reactor. The low thrust electric thrusters allow efficient station keeping and long-term maneuvering. The direct thrust capability can provide tens of pounds of thrust at a specific impulse of around 730 seconds for maneuvers that must be performed more rapidly. The direct thrust allows the nuclear power system to move a payload from Low Earth Orbit (LEO) to Geosynchronous Earth Orbit (GEO) in less than one month using approximately half the propellant of a cryogenic chemical stage.

Two-phase capillary loops are being extensively studied as heat collection and rejection systems for space applications as they appear to satisfy several requirements like low weight, low volume, temperature control under variable heat loads and/or heat sink, operation under on ground and micro gravity conditions, simplicity of mounting and heat transfer through tortuous paths. In 1998–2000 Alenia defined and Lavochkin Association developed the Deployable Radiator on the base of honeycomb panels, axial grooved heat pipes and Loop Heat Pipe. It was designed for on-ground testing.

Most of current jet aircraft circulate fuel on the airframe to match heat loads with available heat sink. The demands for thermal management in wide range of air vehicle systems are growing rapidly along with the increased mission power, vehicle survivability, flight speeds, and so on. With improved aircraft performance and growth of heat load created by Aircraft Mounted Accessory Drive (AMAD) system and hydraulic system, effectively removing the large amount of heat load on the aircraft is gaining crucial importance. Fuel is becoming heat transfer fluid of choice for aircraft thermal management since it offers improved heat transfer characteristics and offers fewer system penalties than air. In the scope of this paper, an AMESim model is built which includes airframe fuel and hydraulic systems with AMAD gearbox of a jet trainer aircraft. The integrated model will be evaluated for thermal performance.

A 3D computer model named AIPAC (Aircraft Ice Protection Analysis Code) suitable for thermal ice protection system parametric studies has been developed. It was derived from HASPAC, which is a 2D anti-icing model developed at Wichita State University in 2010. AIPAC is based on the finite volumes method and, similarly to HASPAC, combines a commercial Navier-Stokes flow solver with a Messinger model based thermodynamic analysis that applies internal and external flow heat transfer coefficients, pressure distribution, wall shear stress and water catch to compute wing leading edge skin temperatures, thin water flow distribution, and the location, extent and rate of icing. In addition, AIPAC was built using a transient formulation for the airfoil wall and with the capability of extruding a 3D surface grid into a volumetric grid so that a layer of ice can be added to the computational domain.

The transition towards More Electric Aircraft (MEA) architectures has challenges relating to integration of power electronics with the starter generator system for on-engine application. To efficiently operate the power electronics in the hostile engine environment at high switching frequency and for better thermal management, use of silicon carbide (SiC) power devices for a bi-directional power converter is examined. In this paper, development of a 50 kVA bi-directional converter operating at an ambient temperature of about 2000C is presented. The design and operation of the converter with details of control algorithm implementation and cooling chamber design are also discussed.

A 500 hours endurance test was performed with a heavy-duty engine (Euro IV); MAN type D 0836 LFL 51 equipped with a PM-Kat®. As fuel 100% biodiesel was used that met the European specification EN 14214. The 500 hours endurance test included both the European stationary and transient cycle (ESC and ETC) as well as longer stationary phases. During the test, regulated emissions (carbon monoxide, nitrogen oxides, hydrocarbons and particulate matter), the particle number distribution and the aldehydes emission were continuously measured. For comparison, tests with fossil diesel fuel were performed before and after the endurance test. During the endurance test, the engine was failure-free for 500 hours with the biogenic fuel. There were almost no differences in specific fuel consumption during the test, but the average exhaust gas temperature increased by about 15°C over the time. Emissions changed only slightly during the test.

Offering aircraft fuel efficiency improvements of 30 to 40% over the powerplants it will replace, PW2037 retrofit in the 727-200 Advanced and B-52 aircraft is attracting heightened interest. A comparison of PW2037 technical characteristics with current aircraft powerplants substantiates the improvement potential.The engine installation and modifications necessary for aircraft system compatibility do not impose significant increases in complexity or cost. The resultant improvements in aircraft capability (727 and B-52) and economic viability to airlines (7271 produce aircraft uniquely suited to today's operational requirements and constrained equipment budgets.

The 912 engine is a well known 4-cylinder horizontally opposed 4-stroke liquid-/air-cooled aircraft engine. The 912 family has a strong track record: 40 000 engines sold / 25 000 still in operation / 5 million flight hours annually. 88% of all light aircraft OEMs use Rotax engines. The 912iS is an evolution of the Rotax 912ULS carbureted engine. The “i” stands for electronic fuel injection which has been developed according to flight standards, providing a better fuel efficiency over the current 912ULS of more than 20% and in a range of 38% to 70% compared to other competitive engines in the light sport, ultra-light aircraft and the general aviation industry. BRP engineers have incorporated several technology enhancements. The fully redundant digital Engine Control Unit (ECU) offers a computer based electronic diagnostic system which makes it easier to diagnose and service the engine.

Boiling heat transfer in a water heat pipe is investigated with the objective of relating heat flux and temperature drop across the evaporator. Nucleate boiling has been postulated as the heat transfer mechanism at and near the wall. A correlation has been obtained that relates evaporator heat flux and temperature drop to various screen-wick and working fluid properties. It is shown to agree well with other available experimental data.

A hydrogen economy is an increasingly popular solution to lower global carbon dioxide emissions. Previous research has been focused on the economic conditions necessary for hydrogen to be cost competitive, which tends to neglect the effectiveness of greenhouse gas mitigation for the very solutions proposed. The holistic carbon footprint assessment of hydrogen production, distribution, and utilization methods, otherwise known as “well-to-wheels” carbon intensity, is critical to ensure the new hydrogen strategies proposed are effective in reducing global carbon emissions. When looking at these total carbon intensities, however, there is no single clear consensus regarding the pathway forward. When comparing the two fundamental technologies of steam methane reforming and electrolysis, there are different scenarios where either technology has a “greener” outcome.

As mission length and the number and complexity of payload experiments increase, so does the probability of thermodegradation contingencies (e.g. fire, chemical release and/or smoke from overheated components or burning materials), which could affect mission success. When a thermodegradation event occurs on board a spacecraft, potentially hazardous levels of toxic gases could be released into the internal atmosphere. Experiences on board the Space Shuttle have clearly demonstrated the possibility of small thermodegradation events occurring during even relatively short missions. This paper will describe the Combustion Products Analyzer (CPA), which is being developed under the direction of the Toxicology Laboratory at Johnson Space Center to provide necessary data on air quality in the Shuttle following a thermodegradation incident.

A unique heat exchanger has been developed with potential applications for cooling high power density electronics and perhaps high energy laser mirrors. The device was designed to absorb heat fluxes of approximately 50 w/cm2 (158,000 Btu/hr.ft2) with a low thermal resistance, a high surface temperature uniformity and very low hydraulic pumping power. A stack of thin copper orifice plates and spacers was bonded together and arranged to provide liquid jet impingement heat transfer on successive plates. This configuration resulted in effective heat transfer coefficients, based on the prime surface, of about 85,000 w/m2 °C (15,000 Btu/hr.ft2 °F) and 1.8 watts (.002 HP) hydraulic power with liquid Freon 11 as coolant.

The flow through most turbomachinery blade rows is characterized by unsteady, viscous, transitional flow. The accurate prediction of the onset of transition from laminar to turbulent flow is essential for calculating heat transfer and performance quantities. The purpose of this investigation is to evaluate the accuracy of four different algebraic transition models which have been combined with an algebraic turbulence model. Numerical experiments have been performed for flow through a turbine rotor cascade with heat transfer, and a cascade of compressor blades. In addition, a study was performed to determine the effects of the computational grid density on the transition location.

In an effort to help future crewed spacecraft thermal control analysts understand the characteristics of one-and two-loop Active Thermal Control Systems (ATCS), a comparison was made between the one- and two-loop ATCS architectures officially proposed for the Crew Exploration Vehicle (CEV) in Design Analysis Cycle 1 (DAC1) and DAC2, respectively. This report provides a description of each design, along with mass and power estimates derived from their respective Master Equipment List (MEL) and Power Equipment List (PEL). Since some of the components were sized independent of loop architecture (ex. coldplates and heat exchangers), the mass and power for these components were based on the MEL and PEL of the most mature design (i.e. two-loop architecture). The mass and power of the two architectures are then compared and the ability of each design to meet CEV requirements is discussed.

In recent years, a tremendous interest has spawned towards adapting Lithium-Ion battery technology for aircraft applications. Lithium-Ion technology is already being used in some military aircraft (e.g., the F-22, F-35 and the B-2) and it has also been selected as original equipment for large commercial aircraft (e.g., the Airbus A380 and Boeing B787). The advantages of Lithium-Ion technology over Lead-Acid and Nickel-Cadmium technologies are higher specific energy (Wh/kg) and energy density (Wh/L), and longer cycle life. Saving weight is especially important in aircraft applications, because it can boost fuel economy and increase mission capability. Disadvantages of Lithium-Ion technology include higher initial cost, limited calendar/float life, inferior low temperature performance, and more severe safety hazards. This paper will present a direct comparison of a 24-Volt, 28Ah Lead-Acid and a 24-volt, 28Ah Lithium-Ion aircraft battery.

Both humans and onboard radiosensitive systems (electronics, materials, payloads and experiments) are exposed to the deleterious effects of the harsh space radiations found in the space environment. The purpose of this paper is to present the space radiation environment extended to deep space based on environment models for the moon, Mars, Jupiter, and Saturn and compare these radiation environments with the earth's radiation environment, which is used as a comparative baseline. The space radiation environment consists of high-energy protons and electrons that are magnetically “trapped” in planetary bodies that have an intrinsic magnetic field; this is the case for earth, Jupiter, and Saturn (the moon and Mars do not have a magnetic field). For the earth this region is called the “Van Allen belts,” and models of both the trapped protons (AP-8 model) and electrons (AE-8 model) have been developed.

This paper describes a computational technique for prediction of the flow and thermal environment in the Space Shuttle Solid Rocket Motor field joint cavities. The SRM field joint hardware has been tested with a defect in the insulation. Due to this defect, the O-ring gland cavities are pressurized during the early part of the ignition. A computer model has been developed to predict the flow and thermal environment through the simulated flaw, during the pressurization of the field joint. The transient mass, momentum, and energy conservation equations in the flow passage in conjunction with the thermodynamic equation of state are solved by a fully implicit iterative numerical procedure. Since this is a conjugate flow and heat transfer problem, wall temperatures are calculated by solving the one-dimensional transient heat conduction equation in the solid along with the other governing equations. The pressure and temperature predictions have been compared with the test data.

A concept for a miniature, mechanically pumped two-phase cooling loop with high thermal performance was developed. In this feasibility study, a miniature, annular gear pump was inserted into the liquid line of a two-phase LHP-type loop architecture. In contrast to capillary-pumped systems, the functions of liquid pumping and evaporative heat transfer were separated and could be optimized independently. The cooling system was tested in terms of heat transport capability, performance and stability using water as the working fluid. The results show a high heat transfer coefficient of >11 W/(cm2K), a high heat transport capability of >70 W/cm2, and stable working behavior in all orientations. These results were obtained with a device using a simple loop architecture and an evaporator design that was not optimized for this kind of operation.

A connectable/disconectable thermal interface has been developed for the constructable radiator system under development at NASA-Johnson Space Center. A contact heat exchanger approach which involves pressurized clamping of a segmented cylindrical heat exchanger on the outside of a round heat pipe evaporator section was designed, fabricated, and tested. Dry metal-to-metal contact conductance heat transfer is utilized. Test results have indicated excellent contact conductances of up to 8500 w/m2°c (1500 Btu/ft2°F) at 2000 kPa (300 psi) clamping force. The feasibility and fabricability of the design have been demonstrated.

The Shuttle orbiter currently uses hydrazine-powered APU’s for powering its hydraulic system pumps. To enhance vehicle safety and reliability, NASA is pursuing an APU upgrade where the hydrazine-powered turbine is replaced by an electric motor pump and battery power supply. This EAPU (Electric APU) upgrade presents several thermal control challenges, most notably the new requirement for moderate temperature control of high-power electronics at 132 °F (55.6 °C). This paper describes how the existing Water Spray Boiler (WSB), which currently cools the hydraulic fluid and APU lubrication oil, is being modified to provide EAPU thermal management.