Search Results

A springback study on three rail type panels is summarized. Numisheet'96 S-rail, A/S P rail II and a Daimlerchrysler rail are presented with experiment data and FEA simulation predictions. The details of the measurement on experiment samples and simulation models are illustrated. The comparison between the experiment data and the simulation results from four different softwares is made on separate cases. The correlation between experiment data and simulation results is analyzed.

Transfer Path Analysis (TPA) is a widely used methodology in Noise, Vibration and Harshness (NVH) analysis of motor vehicles. Either it is used to design a vehicle from scratch or it is applied to root cause an existing NVH problem, TPA can be a useful tool. TPA analysis is closely related to the concept of partial contribution. The very basic assumption in TPA is that the summation of all partial contributions from different paths constitutes the total response (which could be either tactile or acoustic). Another popular concept in NVH analysis of vehicles is the component sensitivity. Component sensitivity is a measure of how much the response changes due to a change in one of the components of the system, i.e., the thickness of a panel or elastic rate of an engine mount. Sensitivity rates are more popular among CAE/Simulation community, simply because they are reasonably easy to calculate using mathematical models.

Cylinder deactivation is a means of improving the fuel economy of gasoline engines. This paper covers the application of the technology to a V8 engine and implementation into vehicles. The description of the engine hardware and its operation are discussed. The engine and transmission control strategy are described, including an example of the compensation strategies to smooth the transition between the different modes of engine operation. The powertrain and chassis hardware changes required to address the noise vibration and harshness issues are discussed and examples of untuned systems are shown.

In a vehicle NVH development and refinement phase, it is necessary to understand the source of the noise and vibration from various powertrain and drivetrain mechanisms. The noise and vibration generated by a drivetrain in a vehicle is a complicate but significant source of physical mechanism, which might become important issues in early or later phase of the vehicle development. For the diagnostic purpose of the drivetrain, a rear-wheel drive (RWD) vehicle in early development phase has been used to measure the bending and torsional vibration of the drivetrain, as well as the vehicle interior noise simultaneously, while the vehicle is running up and down under quasi-steady state on a chassis dynamometer. The lower frequency resonances of torsional and bending vibrations from the drivetrain are correlated with the vehicle interior boom or overall loudness.

The effect of forming strains on the fatigue behavior of an automotive mild steel, interstitial free steel, was studied after being prestrained by balanced biaxial stretch and plane strain. In the long life region, higher than 5×105 reversals, prestrain improves fatigue resistance. In the short life region, prestrain reduces fatigue resistance. At even shorter fatigue lives, the detrimental effect of prestrain diminishes. For plane strains, the fatigue behavior is anisotropic. In the direction perpendicular to the major strain, the steel exhibits much better fatigue resistance than in the direction parallel to the major strain.

The recent trends of increasing driveline torque and use of traction control devices call for increasingly higher durability capacity from driveline components. Bench and vehicle durability tests are often used to validate designs, but they are not cost-effective and take months to complete. Traditional finite element analysis (FEA) procedures have been used effectively in the re-design of driveline components to reduce stress, and occasionally, to predict fatigue life. But in the case of certain rotating components, such as the Axle Differential Case, where the component sees large stress/strain fluctuations within the course of one complete rotation, even under constant input torque, historical fatigue analysis (when conducted) yields very conservative results. The axle differential case tends to be one of the weakest links in the rear axle assembly. Therefore, there is a crucial need for analytical methods to more accurately predict fatigue life to reduce testing time and cost.

During the initial vehicle design phase and as the first prototypes are built, extensive on-board instrumentation and data acquisition is required at the proving grounds (PG). The data is used for various types of testing and analysis. During this phase of development very few parts and assembly components are available for physical test. The objective is to develop a component test for the truck box. This test can be run without suspension parts during the early stages of the vehicle development. A further objective is to correlate the test to FEA models and actual Proving Ground full vehicle test results.

Door mirrors have a major impact on wind noise observed at the driver's ear. The mirror distance and angle with respect to the front side glass will influence the front window buffeting characteristics of the vehicle as well. Optimizing the mirror angle to minimize or eliminate buffeting while maintaining acceptable wind noise performance can provide additional customer satisfaction. Changes to the mirror angle were investigated experimentally for both wind noise and buffeting effects. Experimental vehicle interior noise and buffeting data was taken at multiple yaw angles and wind speeds using a full scale aero acoustic wind tunnel. In addition, experimental wind noise attributes for the different mirror angles was also used to determine the optimal angle. The resulting angle measurement will be used as a best practice mirror angle for optimal wind noise and front window buffeting performance on future vehicle programs.

Historically, pump noise can be a contributor to customer dissatisfaction with automatic transmissions. In this paper, a Shainin experiment was conducted to identify all probable root causes for pump noise on a production RWD transmission. Sample transmissions were selected following subjective evaluations. Noise was objectively measured in the lab using a microphone and an accelerometer. The study was conducted following a systematic Shainin statistical engineering methodology, which included the following major steps: selection of the test measure using the isoplot technique, selection of Best of Best (BOB) and Worst of Worst (WOW) transmissions, assessment of assembly variation, component search, and pair-wise comparisons. The study successfully highlighted the key variables on the drive gear involute profile, which are now being tightly controlled for improved noise characteristics.

The staircase fatigue testing method is a recognized method for determining the fatigue limit of powertrain components. The purpose of this paper is to improve upon existing standards by adding common practices that will ensure a higher degree of statistical accuracy in the data. This includes specifying appropriate sample sizes, stress increments and initial load conditions, as well as making suggestions for appropriate methods of analyzing the data. Two methods (Dixon and Mood method and probit analysis method) are selected and compared in terms of relative percent difference on four parameters (mean, standard deviation, B10 fatigue strength and B50 fatigue strength). The staircase data are obtained by simulations from normal and lognormal fatigue limit distributions.

The springback behavior might be different due to different gap clearances between die and punch. A study using FEA simulation is done to investigate the die gap effect. A 3D brick element and an explicit-implicit method are employed to investigate a few simple problems. A draw form, a crash form with an upper pad and a flange form are investigated separately. Numisheet’93 2D draw bending springback problem is also investigated using an explicit dynamic code. Comparisons between springback simulation results on several different die gaps are illustrated. The Kirchhoff assumption of C° shell element and the Mindlin/Love assumption of thin shell element are also examined on different cases. A case study then is performed on a rail type panel. Conclusions and recommendations for future studies are summarized.

A Draw Bead Simulator (DBS), with modified draw beads, was employed in this study to understand the springback behavior of sheet metal subjected to multiple bending-unbending cycles. The investigations were carried out in both the rolling and the transverse rolling directions on four types of materials: Electro-Galvanized DQ steel, light and heavy gauge Hot-Dip Galvanealed High Strength Steels, and Aluminum alloy AL6111. The sheet geometries, thickness strains, pulling forces and clamping forces were measured and analyzed for the purpose of establishing a benchmark database for numerical predictions of springback. The results indicate that the springback curvature changes dramatically with the die holding force. The conditions at which the springback is minimized was observed and found to depend on the material properties and the sheet thickness. Analysis with an implicit FEM showed that the predicted and the experimental results are in very good agreement.

In the past several years there has been a significant effort to increase the reliance on CAE technology to guide the vehicle design process, with the accompanying effort to reduce or eliminate vehicle prototype testing during the early design phase. Since little or no representative hardware is available early in the design, a tool is needed which allows NVH Development Engineers to subjectively experience the results of NVH CAE model predictions in a realistic driving environment. This paper documents the development of a high fidelity NVH simulator, including both audio and vibration, and the integration of this simulator into an “operator-in-the-loop” Driving Simulator. The key development of this system is its ability to incorporate NVH CAE predictions into the simulated driving environment.

Hot Isostatic Pressing (HIP) has been routinely used to densify castings for aerospace and medical applications for over 30 years. While HIP is widely known to improve the toughness and fatigue life of castings through the healing of internal porosity, it has been perceived as too expensive for most cast aluminum alloys for automotive applications. Recent developments suggest that the cost effectiveness of certain special HIP processes should be revisited due to reductions in process cost and improvements in throughput. This paper will evaluate the Densal® II process applied to a front aluminum steering knuckle. Two casting processes representing differing levels of relative cost and quality were evaluated. The first was Alcoa's VRC/PRC process, a metal mold process with bottom fill, evacuation before fill and pressurization after fill. This is considered to be a premium quality, but higher cost casting process that is already qualified for this application.

In this paper, responses from a vehicle's suspension, chassis and body, are used to demonstrate a methodology to optimize physical test results. It is well known that there is a variability effect due to an increase of wheel unsprung mass (due to loads measurement fixturing), tire pressure, speed, etc. This paper quantifies loading variability due to Wheel Force Transducer (WFT) unsprung mass by using a rainflow cycle counting domain. Also, presents a proving ground-to-test correlation study and the data reduction techniques that are used in road simulation test development to identify the most nominal road load measurement. Fundamental technical information and analytical methodology useful in overall vehicle durability testing are discussed. Durability testing in a laboratory is designed to correlate fatigue damage rig to road. A Proving Ground (PG) loading history is often acquired by running an instrumented vehicle over one or more PG events with various drivers.