Search Results

Nowadays stringent emission regulations are pushing towards new air management strategies like LP-EGR and HP/LP mix both for passenger car and heavy duty applications, increasing the engine control complexity. Within a project in collaboration between Kohler Engines EMEA, Politecnico di Torino, Ricardo and Denso to exploit the potential of EGR-Only technologies, a 3.4 liters KDI 3404 was equipped with a two stage turbocharging system, an extremely high pressure FIS and a low pressure EGR system. The LP-EGR system works in a closed loop control with an intake oxygen sensor actuating two valves: an EGR valve placed downstream of the EGR cooler that regulates the flow area of the bypass between the exhaust line and the intake line, and an exhaust flap to generate enough backpressure to recirculate the needed EGR rate to cut the NOx emission without a specific aftertreatment device.

This paper presents the modeling of the transient phase of catalyst heating on a high-performance turbocharged spark ignition engine with the aim to accurately predict the exhaust thermal energy available at the catalyst inlet and to provide a “virtual test rig” to assess different design and calibration options. The entire transient phase, starting from the engine cranking until the catalyst warm-up is completed, was taken into account in the simulation, and the model was validated using a wide data-set of experimental tests. The first step of the modeling activity was the combustion analysis during the transient phase: the burn rate was evaluated on the basis of experimental in-cylinder pressure data, considering both cycle-to-cycle and cylinder-to-cylinder variations.

Numerical simulation can be effectively used to reduce the experimental tests which are nowadays required for the analysis and calibration of engine control systems. In particular in this paper the use of a one-dimensional engine model to analyze the response of an UEGO sensor in the exhaust manifold of a 4 cylinder s.i. engine (with multipoint fuel injection) is described: numerical simulation has been used to simulate a misfunction of the fuelling system, which caused one of the four cylinders to be fuelled with an air/fuel ratio that was 10% richer than the others. The simulated UEGO response was then compared with experimental measurements, and after this validation process, the sensor model can be used to study a proper fuel injection control strategy thus reducing the required experimental tests, as outlined in a test case presented at the end of the paper.

Nowadays numerical simulations play a major role in the development of future sustainable powertrain thanks to their capability of investigating a wide spectrum of innovative technologies with times and costs significantly lower than a campaign of experimental tests. In such a framework, this paper aims to assess the predictive capabilities of an 1D-CFD engine model developed to support the design and the calibration of the innovative highly efficient spark ignition engine of the PHOENICE (PHev towards zerO EmissioNs & ultimate ICE efficiency) EU H2020 project. As a matter of fact, the availability of a reliable simulation platform is crucial to achieve the project target of 47% peak indicating efficiency, by synergistically exploiting the combination of innovative in-cylinder charge motion, Miller cycle with high compression ratio, lean mixture with cooled Exhaust Gas Recirculation (EGR) and electrified turbocharger.

The use of Ducted Fuel Injection (DFI) for attenuating soot formation throughout mixing-controlled diesel combustion has been demonstrated impressively effective both experimentally and numerically. However, the last research studies have highlighted the need for tailored engine calibration and duct geometry optimization for the full exploitation of the technology potential. Nevertheless, the research gap on the response of DFI combustion to the main engine operating parameters has still to be fully covered. Previous research analysis has been focused on numerical soot-targeted duct geometry optimization in constant-volume vessel conditions. Starting from the optimized duct design, the herein study aims to analyze the influence of several engine operating parameters (i.e. rail pressure, air density, oxygen concentration) on DFI combustion, having free spray results as a reference.

Different diagnostic techniques were experimentally tested on a common rail automotive 4 cylinder diesel engine in order to evaluate their capabilities to fulfill the California Air Resources Board (CARB) requirements concerning the monitoring of fuel injected quantity and timing. First, a comprehensive investigation on the sensitivity of pollutant emissions to fuel injection quantity and timing variations was carried out over 9 different engine operating points, representative of the FTP75 driving cycle: fuel injected quantity and injection timing were varied on a single cylinder at a time, until OBD thresholds were exceeded, while monitoring engine emissions, in-cylinder pressures and instantaneous crankshaft revolution speed.

In this study, a new EGR control technique, based on the estimate of the oxygen concentration in the intake manifold, was firstly investigated through numerical simulation and then experimentally tested, both under steady state and transient conditions. The robustness of the new control technique was also tested and compared with that of the conventional EGR control technique by means of both numerical simulation and experimental tests. Substantial reductions of the NOx emissions under transient operating conditions were achieved, and useful knowledge for controlling the EGR flow rate more accurately was obtained.

A quasi-dimensional multizone combustion model, that was previously developed by the authors, has been refined and applied for the analysis of combustion and emission formation in a EURO V diesel engine equipped with a piezo indirect-acting injection system. The model is based on the integration of the predictive non-stationary variable-profile 1D spray model recently presented by Musculus and Kattke, with a diagnostic multizone thermodynamic model specifically developed by the authors. The multizone approach has been developed starting from the Dec conceptual scheme, and is based on the identification of several homogeneous zones in the combustion chamber, to which mass and energy conservation laws have been applied: an unburned gas zone, made up of air, EGR (Exhaust Gas Recirculation) and residual gas, several fuel/unburned gas mixture zones, premixed combustion burned gas zones and diffusive combustion burned gas zones.

Although the use of Exhaust Gas Recirculation (EGR) is nowadays mandatory for automotive diesel engines to achieve NOx emissions levels complying with more and more stringent legislation requirements, electronically controlled EGR systems still represent an expensive technology, often unsuitable for small diesel engines for off-road applications or for two/three wheelers. An interesting option for these categories of small diesel engines is the so-called “internal EGR”, which is obtained by modifying the intake or the exhaust valve lift profile, in order to increase the fraction of exhaust residuals at the end of the intake stroke. Different valve lift profiles were therefore evaluated for a 2 cylinders, 700 cc, Lombardini IDI diesel engine, equipping a light 4 wheelers vehicle.

The paper presents the main results of a study on the simulation of energy efficient management of on-board electric and thermal systems for a medium-size passenger vehicle featuring a parallel-hybrid diesel powertrain with a high-voltage belt alternator starter. A set of advanced technologies has been considered on the basis of very aggressive fuel economy targets: base-engine downsizing and friction reduction, combustion optimization, active thermal management, enhanced aftertreatment and downspeeding. Mild-hybridization has also been added with the goal of supporting the downsized/downspeeded engine performance, performing energy recuperation during coasting phases and enabling smooth stop/start and acceleration. The simulation has implemented a dynamic response to the required velocity and manual gear shift profiles in order to reproduce real-driver behavior and has actuated an automatic power split between the Internal Combustion Engine (ICE) and the Electric Machine (EM).

In this work, a methodology for building and calibrating the kinetic scheme for the 1D CFD model of a zone-coated automotive Diesel Oxidation Catalyst (DOC) by means of a Genetic Algorithm (GA) approach is presented. The methodology consists of a preliminary experimental activity followed by a modelling, optimization and validation process. The tested aftertreatment component presents zone coating, with the front brick side covered with Zeolites in order to ensure hydrocarbons trapping at low temperature, and Platinum Group Metal (PGM), while the rear brick side presents an alumina washcoat with a different PGM loading. Reactor scale samples representative of each coating zone were tested on a Synthetic Gas Bench (SGB), to fully characterize the component’s behavior in terms of Light-off and hydrocarbons (HC) storage for a wide range of inlet feed compositions and temperatures, representative of engine-out conditions.

The unsteady flow effects in two different close coupled catalytic converters were investigated in order to achieve a better understanding of the steady state experimental tests which are usually performed to evaluate a flow distribution. Firstly the validity of a CFD model was achieved through a comparison of some steady state simulations with the results of HWA experimental measurements. Several different formulations of the uniformity index, that were found in literature, were then compared, trying to highlight the strengths and shortcomings of each one. Further information was derived from a comparison of the two catalysts that were tested to achieve a general methodology that would be useful for future analysis. Finally, a new approach to evaluate the flow distribution using a steady state analysis was proposed by comparing the results of a transient simulation that was obtained for a whole engine cycle.

In this work, several nanostructured ceria-based catalysts were prepared by the hydrothermal technique varying two synthesis parameters (namely, temperature and pH). Then, cerias with different shapes (i.e., cubes, rods, combination of them, other polyhedra) and structural properties were obtained. The prepared materials were tested for the CO oxidation and soot oxidation efficiency. The results have shown that, for the CO oxidation, activities depend on the surface properties of the catalysts. Conversely, for the soot oxidation, the most effective catalysts exhibit better soot-catalyst contact conditions.

The fuel injection plays a crucial role in determining the mixture formation process in Gasoline Direct Injection (GDI) engines. Pollutant emissions, and soot emissions in particular, as well as phenomena affecting engine reliability, such as oil dilution and injector coking, are deeply influenced by the injection system features, such as injector geometric characteristics (such as injector type, injector position and targeting within the combustion chamber) and operating characteristics (such as injection pressure, injection phasing, etc.). In this paper, a new CFD methodology is presented, allowing a preliminary assessment of the mixture formation quality in terms of expected soot emissions, oil dilution and injector coking risks for different injection systems (such as for instance multihole or swirl injectors) and different injection strategies, from the early stages of a new engine design.

Gasoline direct injection in two-stroke engines has led to even more advantageous results, in comparison with four-stroke engines, as far as unburned hydrocarbon emissions and fuel consumption are concerned. A new electronically controlled injection system has therefore been fitted in a crankcase-scavenged two-stroke engine, previously set up with indirect injection equipment. The comparison between the performance of the two gasoline feeding systems has highlighted the potential of the direct injection strategy. The direct injection system here tested has allowed the optimization of the engine torque characteristic at wide open throttle operating conditions. Moreover, the engine original exhaust system, has been replaced with an expansion-chamber exhaust-pipe system, in order to evaluate the impact of direct gasoline injection also with these optimized exhaust configuration.

Heat transfer in the combustion chamber of s.i. engines operating under knocking conditions has been detected and analyzed. Measurements have been carried out, cycle by cycle, on a CFR laboratory engine by means of a dedicated instrument and an original method. The relationship between heat transfer and knock intensity has been analyzed on a statistical basis, emphasizing knock intensity influence on heat transfer distribution. Moreover, the share of heat transfer more closely related to knock intensity has been highlighted: heat transfer is shown not to be significantly affected by knock intensity under light-to-medium knock conditions; on the contrary, the influence becomes evident under medium-to-heavy knock conditions. Eventually, heat transfer indexes influenced by knock intensity have been evaluated, allowing a comparison of knock-related thermal properties of fuels.

In this work different internal and external EGR strategies, combined with extreme Miller cycles, were analyzed by means of a one-dimensional CFD simulation code for a Wärtsilä 6-cylinder, 4-strokes, medium-speed marine diesel engine, to evaluate their potential in order to reach the IMO Tier 3 NOx emissions target. By means of extreme Miller cycles, with Early Intake Valve Closures (up to 100 crank angle degrees before BDC), a shorter compression stroke and lower charge temperatures inside the cylinder can be achieved and thanks to the cooler combustion process, the NOx-specific emissions can be effectively reduced. EIVC strategies can also be combined with reductions of the scavenging period (valve overlap) to increase the amount of exhaust gases in the combustion chamber. However, the remarkably high boost pressure levels needed for such extreme Miller cycles, require mandatorily the use of two-stage turbocharging systems.

A real-time mean-value engine model for the simulation of the HRR (heat release rate), in-cylinder pressure, brake torque and pollutant emissions, including NOx and soot, has been developed, calibrated and assessed at both steady-state and transient conditions for a Euro 6 1.6L GM diesel engine. The chemical energy release has been simulated using an improved version of a previously developed model that is based on the accumulated fuel mass approach. The in-cylinder pressure has been evaluated on the basis of the inversion of a single-zone model, using the net energy release as input. The latter quantity was derived starting from the simulated chemical energy release, and evaluating the heat transfer of the charge with the walls. NOx and soot emissions were simulated on the basis of semi-empirical correlations that take into account the in-cylinder thermodynamic properties, the chemical energy release and the main engine parameters.

The role of numerical simulations in the development of innovative and sustainable powertrains is constantly growing thanks to their capabilities to significantly reduce the calibration efforts and to point out potential synergies among different technologies. In such a framework, this paper describes the development of a fully physical 1D-CFD engine model to support the calibration of the highly efficient spark ignition engine of the PHOENICE (PHev towards zerO EmissioNs & ultimate ICE efficiency) EU H2020 project. The availability of a reliable simulation platform is essential to effectively exploit the combination of the several features introduced to achieve the project target of 47% peak gross indicated efficiency, such as SwumbleTM in-cylinder charge motion, Miller cycle combined with high Compression Ratio (CR), lean mixture exploiting cooled low pressure Exhaust Gas Recirculation (EGR) and electrified turbocharging.

Nowadays control system development in the automotive industry is evolving rapidly due to several factors. On the one hand legislation tightening is asking for simultaneous emission reduction and efficiency increase, on the other hand the complexity of the powertrain is increasing due to the spreading of electrification. Those factors are pushing for strong design parallelization and frontloading, thus requiring engine calibration to be moved much earlier in the V-Cycle. In this context, this paper shows how, coupling well known physical 1D engine models featuring predictive combustion and emission models with a fully physical aftertreatment system model and longitudinal vehicle model, a powerful virtual test rig can be built. This virtual test rig can be used for powertrain virtual calibration activities with reduced requirement in terms of experimental data.