Search Results

Abstract The ASTM D130 was first issued in 1922 as a tentative standard for the detection of corrosive sulfur in gasoline. A clean copper strip was immersed in a sample of gasoline for three hours at 50°C with any corrosion or discoloration taken to indicate the presence of corrosive sulfur. Since that time, the method has undergone many revisions and has been applied to many petroleum products. Today, the ASTM D130 standard is the leading method used to determine the corrosiveness of various fuels, lubricants, and other hydrocarbon-based solutions to copper. The end-of-test strips are ranked using the ASTM Copper Strip Corrosion Standard Adjunct, a colored reproduction of copper strips characteristic of various degrees of sulfur-induced tarnish and corrosion, first introduced in 1954. This pragmatic approach to assessing potential corrosion concerns with copper hardware has served various industries well for a century.

Abstract With the introduction of advanced lightweight materials with complex microstructures and behaviors, more focus is put on the accurate determination of their forming limits, and that can only be possible through experiments as the conventional theoretical models for the forming limit curve (FLC) prediction fail to perform. Despite that, CAE engineers, designers, and toolmakers still rely heavily on theoretical models due to the steep costs associated with formability testing, including mechanical setup, a large number of tests, and the cost of a stereo digital image correlation (DIC) system. The international standard ISO 12004-2:2021 recommends using a stereo DIC system for formability testing since two-dimensional (2D) DIC systems are considered incapable of producing reliable strains due to errors associated with out-of-plane motion and deformation.

Abstract Automotive interior coatings for flexible and rigid substrates represent an important segment within automotive coating space. These coatings are used to protect plastic substrates from mechanical and chemical damage, in addition to providing colour and design aesthetics. These coatings are expected to resist aggressive chemicals, fluids, and stains while maintaining their long-term physical appearance and mechanical integrity. Designing such coatings, therefore, poses significant challenges to the formulators in effectively balancing these properties. Among many factors affecting coating properties, the cross-link density (XLD) and solubility parameter (δ) of coatings are the most predominant factors.

Abstract Considering the biodiesel composition, blend percentage, and temperature as input variables in the models to predict biodiesel-diesel blends’ properties is imperative. However, there are no models available in the literature to predict the properties of biodiesel-diesel blends that consider all these variables. The accuracy of spray and combustion models for diesel engines depends on the accuracy at which the fuel properties are estimated. Thus, straightforward approaches to accurately predict the properties of biodiesel-diesel blends are required. A novel reference property-based approach is proposed in the present work to predict the biodiesel-diesel blends’ properties to address this research gap. Models available in the literature correlating the properties of interest to fuel temperature were modified by including a reference property measured at 293 K.

Abstract Many consider hydrogen to be the automobile fuel of the future. Indeed, it has numerous characteristics that makes it very attractive. Hydrogen has a much higher energy density than gasoline, can be produced from water, and its only emission is water. However, there are numerous challenges associated with hydrogen. In particular, the production of hydrogen is a key issue. Currently, most hydrogen is developed from methane, resulting in hydrogen having a carbon footprint. New investments into electrolysis from renewable energy sources is showing promise as an alternative for generating hydrogen. Further, the distribution of hydrogen poses many problems, requiring substantial infrastructure to support a hydrogen economy. Additionally, hydrogen storage is a key issue since most conventional storage mechanisms are overly bulky. If these three issues can be addressed, hydrogen is posed for being a key fuel as the world tries to move away from fossil fuels.

Abstract Recently, lean manufacturing (LM) practices are being combined with tools and techniques that belong to other areas of knowledge such as risk management (RM). Value stream mapping (VSM) is a well-known tool in showing the value, the value stream, and the flow, which represents the three lean principles. VSM and RM, when used in tandem with one another, are more advantageous in covering VSM issues such as the variability of production processes. In this article, a conceptual model that integrates the two is shown and explained. The model helps to generate scenarios of current state map (CSM) and future state map (FSM) in a dynamic way by identifying current and potential risks. These risks might happen in the future, bringing with it negative ramifications including not reaching the main objectives within the defined time. The model has been tested in a coffee production company belonging to health and food sector.

Abstract In this article, a methodology is presented to assess the influence of time-averaged deformations on a production car of the 2018 A-class due to wind load. Exemplary, the deformations of the front and rear bumper are investigated. The aerodynamic development of vehicles at Mercedes-Benz is divided into several phases. When comparing, force coefficients differences can be observed between these distinct hardware stages as well as when comparing steady-state simulations to wind tunnel measurements. In early phases when prototype vehicles are not yet available, so-called aero foam models are used. These are well-defined full-sized vehicle models as the outer skin is milled from Polyurethane. Important aerodynamic characteristics such as an engine compartment with a cooling module, deflecting axles with rotatable wheels, and underbody covers are represented.

Abstract An increase in the efficiency of internal combustion engines is a key challenge for engineers today. Mechanical losses contribute significantly to engine inefficiency, and the piston assembly has the largest share in these losses. Various measures are therefore taken to reduce friction between the piston and the rings against the cylinder. However, the undertaken changes most frequently generate new challenges. For instance, lowering the viscosity of the engine oil or increasing the engine load may lead to accelerated wear of the mating surfaces. In order to resolve this problem, more and more complex materials and anti-wear coatings have to be used. Furthermore, under these conditions, the shape of the ring’s sliding surface becomes more important. This article presents the results of experimental research on the influence of the geometry of the sliding surface and the use of various anti-wear coatings.

Abstract Effects of process parameters such as rotational speed, feed rate, and drill diameters on the drilling behavior of basalt-epoxy-based composites including 2.5 wt.% Al2O3 particles manufactured by mixing and compression method were investigated by Taguchi’s technique. The experimental results showed that the burr height (BH) increased considerably almost linearly with an increase in the drill diameter, while it remained stable with speed and decreased the feed rate slightly. There was an excellent correlation between the control factors and responses, BH of basalt fiber-reinforced plastics (BFRPs) through the Taguchi approach. The model had an adjusted R2 value of 96.3%. Generally, the inclusion of Al2O3 particles in BFRP increased its cutting force properties. Optimized drilling conditions for the input variables to produce the lowest response of the BH for composites were rotational speed of 560 rpm and feed rate of 0.28 mm/rev and a drill diameter of 4.5 mm.

Abstract This study predicts the dynamic characteristics for tires in the development stages of a vehicle with a focus on the generated forces. In particular, this investigation proposes an approximation analysis for the deflection and contact characteristics of a pneumatic tire. This consists of an integrated model for a three-dimensional membrane ring and brush models. This model is more complex than conventional models, which resulted in increased computational costs. Because the tire dynamic characteristics affects the contact pressure, the deformation of the tread rubber caused an interaction of forces. Therefore, the tread ring deformation was defined as a summation of the mode basis functions, which expressed vibrational behavior. This approximation linearizes the energy function, which helped calculate the potential energy of the tire structure using a theoretical equation without discretization.

Abstract To improve the lubrication and friction of the crankpin bearing (CB) in the engine, the design of surface textures on the bearing surface is proposed and researched based on the CB hydrodynamic dynamic model. To enhance the reliability of the research results and its closeness to reality, the optimal CB parameters, the experimental data of the external dynamic load W0 acting on the crankpin, and the CB surface roughness in the well-known existing researches are referred to as input data for the simulation process. The effect of the distribution density {n, m}, diameter D, and depth of the microcircular textures hd on improving the lubrication and friction are then analyzed based on the indexes of the increase in the oil film pressure, decrease in the solid asperity contacts in the mixed lubrication region (MLR), friction force, and coefficient of friction (COF) between the crankpin and bearing surfaces, respectively.

Abstract Metal Pick-Up (MPU) is a problematic phenomenon in automotive disc brakes. MPU generally forms as some metal lumps on the surface of the brake pad. If brake pads have MPU, during braking they would cause grooving of the disc rotor, generating brake noise and deteriorating the performance of the brake. The previous literature has so far reported that the source of the MPU is an Fe component from a disc rotor or brake pads. However, only a few of the generation mechanisms of MPU have been proven. We investigate MPU to completely elucidate the mechanism of MPU generation by using different analyses than the previous literature. First, to find out the source of MPU generation, we focus on the chemical reaction of a certain component with wear debris during braking, and some of the verification experiments are conducted under the conditions of simulated friction interface.

Abstract The windshield wiper is a component that is closely related to safety because it plays an important role in ensuring the driver’s vision despite external factors such as rain and dust. Here, the mechanical properties of different types of blade rubber were evaluated using a miniature tensile test machine for a structural analysis of the types of wiper blade rubber used in automobiles. In addition, a compression set and the aging characteristics of each type of rubber were determined by comparing the mechanical properties and shape changes of the blade rubber after more than one year of use to the same blade rubber before use. Using the mechanical properties as measured by a tensile test, a nonlinear structural analysis of the wiper blade system was conducted using a 3D finite element method (FEM). The contact force distribution and wiping angle of the blade rubber under a static load were measured.

Abstract The increased scope of active and passive safety in motor vehicles and the enforcement of approval requirements for individual parts and assemblies affect the design and parameters of a car’s motion. The tire, which transmits forces and torques onto the road’s surface is a particularly crucial element in the vehicle. Its structure, type of mixture, and operating conditions determine the safety of vehicle motion. The three-axial force system loads the tires of the car and affects both the tread and sidewall, as well as the suspension and steering system. Taking into account the controllability and stability of movement, the tire is subjected to dynamic and thermal loads, as well as to wear and random damage. This negatively impacts on the joints of composite layers. The sudden loss of pressure in the tire can lead to serious accidents, especially when moving at high speeds, due to changes in the rolling radius.

Abstract The transportation industry is currently in a transition toward the use of zero-emission vehicles; however, reaching it will take a considerable amount of time. In the meantime, a diesel powertrain will remain the workhorse for most heavy-duty transportation. In order to reduce the engine’s environmental impact, biofuels, such as biodiesel, are used as drop-in fuels or fuel blends. The use of drop-in fuels may create challenges for the fuel system since sticky deposits can precipitate and cause injector malfunctioning or premature fuel filter plugging. It has been concluded in the past that these deposits have been caused by soft particles. In this article, soft particles created through the degradation of biodiesel and their effect on filters are studied. The article aims to analyze fuel filters and investigate the materials responsible for soft particle separation. The study includes three pre filters and three main filters that are commercially available truck filters.

Abstract The appearance of an automobile is anything but unimportant for the owner. This applies to the acquisition as well as the keeping. In this context, the avoidance of corrosion is a fundamental part of the user’s satisfaction of a company. The body design can be modified to optimize drainage and reduce the risk of corrosion, improving the owner’s satisfaction with the purchase of the automobile. During the proof of concept of water management, as part of the process of development, physical prototypes are state of the art. At this point in the development process, every necessary change is expensive and time consuming. Virtual methods are able to support the development in earlier steps and thus reduce costs. The conventional Computational Fluid Dynamics (CFD) methods could not handle the simulation of a full car in the rain or water passage properly due to much higher computation efforts and deviations from the experiments.

Abstract The purpose of this article was to determine the failure safety margins of the front braking system of a Honda CTX700 motorcycle and to perform a substantive stress analysis on the system, as well as to verify the stresses using FEMAP. It should be noted that in this finite element analysis (FEA), the connections between components are modeled using linear-contact connections that exert forces on adjacent surfaces and are not trivially meshed as one solid with coincident grids with two different section material properties. The first part of the work involved accurately measuring the geometry of each part and three-dimensional (3D) modeling of all components. Measurements were taken via the trivial methods of using a ruler and caliper, and then the 3D model was generated in Solidworks by digitizing the geometric parameters. Some parts of the system were simplified in the 3D model to ensure proper meshing of the model.

Abstract The greatest frictional contributor in an internal combustion engine is the contact between the piston ring pack and cylinder liner. Therefore, an improved lubrication regime has the potential to raise engine efficiency while lowering emissions, aiding to meet environmental regulations. Previous ultrasonic measurements of the oil film thickness (OFT) between piston rings and the cylinder liner in a marine engine have been subject to several unexpected trends. This article refines the measurement to identify and remove these factors, the trends were found to have arisen due to the detection of ultrasonic reflections from the piston ring outside of the expected alignment zone. The extent of these undesired reflections is thought to be due to the liner thickness providing a relatively large distance for spreading of the ultrasonic wavefront.

Abstract Carbon fiber reinforced plastic (CFRP) has been used in automobiles as well as airplanes. Because of its light weight and high strength, CFRP is a good choice for making vehicle bodies lighter, which would improve fuel economy. Conventional metal bodies provide a convenient body return for electric wiring and offer good shielding against electromagnetic fields. Although CFRP is a conductor, its conductivity is much lower than that of metals. Therefore, CFRP bodies are usually not useful for electric wiring. In thunderstorms, an automotive body is considered to be a Faraday cage that protects the vehicle’s occupants from the potential harms of lightning. Before CFRP becomes widely applied to automotive bodies, its electric and electromagnetic properties need to be investigated in order to determine whether it also works as a Faraday cage against lightning. In this article, CFRP and metal body vehicles were tested under artificial lightning.

Abstract Single point incremental forming (SPIF) is a robust and new technique. In the recent research scenario, materials properties such as microstructure, micro-texture analysis, and crystal structure can be accessed through characterization non-destructive techniques, e.g., scanning electron microscope (SEM), electron backscattered diffraction (EBSD), and X-ray diffraction (XRD). XRD is a non-destructive method for analyzing the fine structure of materials. This study explores how process variables such as wall angle, step size, feed rate, and forming speed affect the parts of large-, medium-, and small-sized truncated cones of aluminum alloy AA3003-O sheet. Several cone parts of truncated cones are used in this investigation to implement Scherrer’s method. The two primary determining factors peak height and crystallite size are assessed for additional analysis in the present research.