Search Results

This SAE Standard establishes the minimum construction and performance requirements for a 15 pole connector between towing vehicles and trailers, for trucks, trailers, and dollies, for 12 VDC nominal applications in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.

This SAE standard establishes the minimum construction and performance requirements for a 15 Pole Connector Between Towing Vehicles and Trailers, for trucks, trailers, and dollies in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.

This product includes information on the manufacturer, engine, applications, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds. In addition, this product contains complete engine information such as displacement, cylinder configuration, valve train, combustion cycle, pressure charging, charge air cooling, bore, stroke, cylinder numbering convention, firing order, compression ratio, fuel system, fuel system pressure, ignition system, knock control, intake manifold, exhaust manifold, cooling system, coolant liquid, thermostat, cooling fan, lubricating oil, fuel, fuel shut off speed, etc. Also included are all measured test parameters outlined in J2723.

This dictionary of terms was prepared for use by those with a need to describe and understand the dynamics and handling of two-wheeled, single track vehicles. It is intended to span the gap between vehicle dynamics specialists and those with a more general interest. This report is pertinent to such areas as vehicle design and development, the description of two-wheeler properties, rider training and education, and the preparation of standards and regulations. This report was prepared by the SAE Motorcycle Committee, which solicits suggestions for improvements and additions to be considered in future revisions. Comments should be directed to SAE Headquarters.

This dictionary of terms was prepared for use by those with a need to describe and understand the dynamics and handling of two-wheeled, single track vehicles. It is intended to span the gap between vehicle dynamics specialists and those with a more general interest. This report is pertinent to such areas as vehicle design and development, the description of two-wheeler properties, rider training and education, and the preparation of standards and regulations. This report was prepared by the SAE Motorcycle Committee, which solicits suggestions for improvements and additions to be considered in future revisions. Comments should be directed to SAE Headquarters.

This analysis applies to crane types as covered by Power Crane and Shovel Association Standard Number Two, Mobile Hydraulic Crane Standards and ANSI B30.15; refer to 5.1.

This analysis applies to crane types as covered by Power Crane and Shovel Association Standard Number Two, Mobile Hydraulic Crane Standards and ANSI B30.15; refer to 5.1.

This analysis applies to crane types as covered by ASME B30.5.

This analysis applies to crane types as covered by ASME B30.5.

The procedure applies to heavy vehicles weighing more than 11 800 kg (26 000 lb) and particularly to those vehicles having two or more articulation joints that allow rotation in a horizontal plane. The procedure pertains to the lateral directional response of multi-articulated vehicles in avoidance maneuvers performed at highway speeds without braking.

The test procedure applies to roll coupled units such as straight trucks, tractor semitrailers, full trailers, B-trains, etc. The test is aimed at evaluating the level of lateral acceleration required to rollover a vehicle or a roll-coupled unit of a vehicle in a steady turning situation. Transient, vibratory, or dynamic rollover situations are not simulated by this test. Furthermore, the accuracy of the test decreases as the tilt angle increases, although this is a small effect at the levels of tilt angle used in testing heavy trucks. The test accuracy is accepted for vehicles that will rollover at lateral acceleration levels below 0.5 g corresponding to a tilt table angle of less than approximately 27 degrees. Even so, the results for heavy trucks with rollover thresholds greater than 0.5 g could be used for comparing their relative static roll stability.

The purpose of this SAE Recommended Practice is to provide a common electrical and mechanical interface specification that can be used to design electronic accelerator pedal position sensors and electronic control systems for use in medium—and heavy-duty vehicle applications.

This recommendation establishes a uniform test procedure for evaluating performance of agricultural equipment operator enclosure pressurization systems.

The basic performance characteristics of greatest interest are airflow restriction or pressure drop, dust collection efficiency, dust capacity, and air cleaner structural integrity. This test code therefore addresses itself to the measurement of these parameters.

This test code is for laboratory use in determining the operating characteristics of air cleaners. It refers specifically to laboratory testing of oil bath, oil wetted, dry and multistage air cleaners. Other types should follow this recommended practice wherever applicable. Multistage types should be evaluated as a complete assembly although, if desired, a component stage can be tested separately in accordance with its individual type. This code contains alternate procedures and permits prescribing certain specific conditions of a lest. Therefore reported results of tests are not complete unless accompanied by statements, where applicable, of the specific conditions such as: (1) rated air flow, (2) prescribed air flow. (3) steady or variable airflow, (4) fine or coarse dust, (5) amount of (lust, and (6) maximum permissible restriction.

The basic performance characteristics of greatest interest are airflow restriction or pressure drop, dust collection efficiency, dust capacity, and air cleaner structural integrity. This test code therefore adresses itself to the measurement of these parameters.