Search Results

Charge cooling due to fuel evaporation in a direct-injection spark-ignition (DISI) engine typically allows for an increased compression ratio relative to port fuel injection (PFI) engines. It is clear that this results in a thermal efficiency improvement at part load for homogenous-charge DISI engines. However, very little is known regarding the effect of compression ratio on stratified charge operation. In this investigation, DISI combustion data have been collected on a single cylinder engine equipped with a variable compression ratio feature. The results of experiments performed in stratified-charge direct injection (SCDI) mode show that despite its over-advanced phasing, thermal conversion efficiency improves with higher compression ratios. This benefit is quantified and dissected through an efficiency analysis. Furthermore, since the engine was equipped with both wall-guided DI and PFI systems, direct comparisons are made at part load for fuel consumption and emissions.

Multidimensional modeling is used to study air-fuel mixing in a direct-injection spark-ignition engine. Emphasis is placed on the effects of the start of fuel injection on gas/spray interactions, wall wetting, fuel vaporization rate and air-fuel ratio distributions in this paper. It was found that the in-cylinder gas/spray interactions vary with fuel injection timing which directly impacts spray characteristics such as tip penetration and spray/wall impingement and air-fuel mixing. It was also found that, compared with a non-spray case, the mixture temperature at the end of the compression stroke decreases substantially in spray cases due to in-cylinder fuel vaporization. The computed trapped-mass and total heat-gain from the cylinder walls during the induction and compression processes were also shown to be increased in spray cases.

A CFD based design optimization methodology was developed and adopted to the development of a stratified-charge direct-injection spark ignition (DISI) combustion system. Two key important issues for homogeneous charge operation, volumetric efficiency and mixing homogeneity, are addressed. The intake port is optimized for improved volumetric efficiency with a CFD based numerical optimization tool. It is found that insufficient fuel-air mixing is the root cause for the low rated power of most DISI engines. The fuel-air mixing in-homogeneity is due to the interaction between intake flow and injected fuel spray. An injector mask design was proposed to alleviate such interaction, then to improve air-fuel mixture homogeneity. It was then confirmed with dynamometer testing that the optimized design improved engine output and at the same time had lower soot and CO emissions.

In modeling of engine fuel-air mixing, it is desired to be able to predict fuel spray atomization under different injection and ambient conditions. In this work, a previously developed sheet atomization model was studied for this purpose. For sprays from a pressure-swirl injector, it is assumed in the model that the fuel flows out the injector forming a conical liquid film (sheet), and the sprays are formed due to the disintegration of the sheet. Modified formulations are proposed to estimate sheet parameters including sheet thickness and velocity at the nozzle exit. It was found that the fuel flow rate of a swirl injector satisfied the correlation well. Computations of correlation well. Computations of the sprays injected in an engine with a side-mounted injector were performed for conditions that duplicated a set of experiments performed in an optical engine. The computed results were compared with the spray images obtained from the optical engine using elastic (Mie) scattering.

The interaction between in-cylinder flow and injected fuel spray in direct ignition spark ignition (DISI) engines have been investigated. The study shows that the major effect of intake flow on the fuel spray is that the induced flow tends to make the spray collapse. This deformation of spray will prevent the fuel spray from spreading out, evaporating, and mixing well with air and also increase fuel wetting on the wall. It has been demonstrated that the intake flow effect on the fuel spray can be alleviated by increasing the masking between the two intake ports. Swirl and tumble motion effects on the fuel air mixing and wall wetting in DISI engines were also studied. A counter-rotating vortex structure is identified in the case with tumble dominating in-cylinder flow structure. This vortex structure tends to hinder fuel air mixing and increase wall wetting. It is shown that some swirl motion is helpful to improve mixing quality and decrease the wall wetting.

A numerical study of air-fuel mixing in a direct-injection spark-ignition engine was carried out. In this paper, the numerical models are described and grid generation methods to represent a realistic port-valve-chamber geometry is discussed. To model a vaporizing hollow-cone spray resulting from an automotive pressure-swirl injector, a newly developed sheet spray atomization model was used to compute the processes of disintegration of the liquid sheet and breakup of the subsequent drops. Computations were performed of a particular 4-valve pent-roof engine configuration in which the intake process and an early fuel injection scheme were considered. After an analysis of the intake-generated flow structures in this engine configuration, the spray behavior and the spatial and temporal evolution of fuel liquid and vapor phases are characterized.

Simulation and Optimization of Internal Combustion Engines provides the fundamentals and up-to-date progress in multidimensional simulation and optimization of internal combustion engines. While it is impossible to include all the models in a single book, this book intends to introduce the pioneer and/or the often-used models and the physics behind them providing readers with ready-to-use knowledge. Key issues, useful modeling methodology and techniques, as well as instructive results, are discussed through examples. Readers will understand the fundamentals of these examples and be inspired to explore new ideas and means for better solutions in their studies and work. Topics include combustion basis of IC engines, mathematical descriptions of reactive flow with sprays, engine in-cylinder turbulence, fuel sprays, combustions and pollutant emissions, optimization of direct-injection gasoline engines, and optimization of diesel and alternative fuel engines.

Variable Cam Timing (VCT) has been proven to be a very effective method in PFI (Port Fuel Injection) engines for improved fuel economy and combustion stability, and reduced emissions. In DISI (Direct Injection Spark Ignition) engines, VCT is applied in both stratified-charge and homogeneous charge operating modes. In stratified-charge mode, VCT is used to reduce NOx emission and improve combustion stability. In homogeneous charge mode, the function of VCT is similar to that in PFI engines. In DISI engine, however, the VCT also affects the available fuel-air mixing time. This paper focuses on VCT effects on the induction process and the fuel-air mixing homogeneity in a DISI engine. The detailed induction process with large exhaust-intake valve overlap has been investigated with CFD modeling. Seven characteristic sub-processes during the induction have been identified. The associated mechanism for each sub-process is also investigated.

This paper proposes a film dynamics model for liquid film resulting from fuel spray impinging on a wall surface. It is based on a thin film assumption and uses numerical particles to represent the film to be compatible with the particle spray models developed previously. The Lagrangian method is adopted to govern the transport of the film particles. A new, statistical treatment was introduced of the momentum exchange between the impinging spray and the wall film to account for the directional distribution of the impinging momentum. This model together with the previously published models for outgoing droplets constitutes a complete description of the spray wall impingement dynamics. For model validation, films resulting from impinging sprays on a flat surface with different impingement angles were calculated and the results were compared with the corresponding experimental measurements.