Search Results

The injection rate signals from a commercial diesel fuel injection system, based on a distributor pump driven by a DC motor, were characterised independently and consecutively by two injection rate meters based on the Zeuch and Bosch methods. The signals were first analysed in terms of their shot-to-shot variations over 64 consecutive injections and the correlations between needle lift and injection rate over a range of pump speeds and loads quantified by Fast Fourier Transform. A direct comparison of the injection rate signals on a cycle-resolved basis was achieved by connecting two consecutive injectors from the pump-line-nozzle injection system to a Bosch- and a Zeuch-based injection rate meters. The signals were acquired over a large number of injections in terms of mean and rms of the injected quantity, mean injection rate, maximum injection rate, average cumulative fuel injected and average injection duration.

A computer model simulating the flow in fuel injection systems has been used in order to investigate the fuel injection processes in an in-line pump-based fuel injection system for direct-injection diesel engines. The model is one-dimensional and it is based on the mass and momentum conservation equations for the simulation of the fuel flow and on the equilibrium of forces for the simulation of the mechanical movements of the valves present in the system. The fuel injection system tested comprised an in-line pump whose characteristics were examined by using as input the measured line pressure signal and by modeling the pump operation itself as well as the fuel flow through single- and two-stage injectors. For the validation of the model, extensive comparison with experimental data has been performed for a wide range of pump operating conditions.

Local measurements of the mean and rms velocities have been obtained by laser Doppler velocimetry in the coolant passages of a transparent model of a Ford 2.5L diesel cylinder head and block at a steady flowrate of 6.83 × 10-4 M3/s. The simulation of the coolant fluid by a mixture of hydrocarbon fluids at a predetermined constant temperature allowed accurate matching of the refractive index to that of the acrylic model, thus providing optical access for LDV measurements of the internal flow in sensitive areas where cooling is essential to prevent metal-fatigue failure. The results were obtained in sufficient detail to allow further validation of CFD coolant flow models.

The electrical characteristics of transistorized coil ignition (TCI) and capacitor discharge ignition (CDI) systems were investigated in spark-ignited quiescent and flowing propane/air mixtures within an optically-accessible, cylindrical constant-volume combustion chamber. Under quiescent flow conditions, the initial pressure, temperature and equivalence ratio of the mixture as well as the spark gap width and geometry were varied systematically in order to examine the relationship between ignition characteristics and flame initiation and development. The effect of the flow in the spark gap on the electrical characteristics of the ignition system, mixture ignitability and flame development was also examined by varying the pre-ignition mean flow and turbulence as well as the spark plug orientation relative to the mean flow.

Laser Doppler velocimetry, phase Doppler anemometry and Mie scattering were applied to a single-cylinder, four-valve, spark-ignition gasoline research engine equipped with a fully transparent liner and piston, to obtain information about the tumble flow and the droplet size and velocity distributions during induction and compression, for lean air/fuel mixture ratios of 17.5 and 24 and with closed-valve and open-valve fuel injection. The mixture distribution obtained with the two injection strategies was correlated with flame images, pressure analysis and exhaust emissions which confirmed the advantages of combining open-valve injection with tumble to allow stable and efficient engine operation at an air/fuel ratio of 24 through charge stratification and faster flame growth.

The effect of various levels of exhaust gas recirculation (EGR) on the combustion characteristics has been investigated in the four-cylinder 1.9L direct-injection optical VW diesel engine in terms of the cylinder pressure, flame development, temperature and KL-factor distributions. Images of the developing flame under twelve engine operating conditions including 1000rpm/idle, 2000rpm/2 bar bmep and 2000rpm/10 bar bmep at 0%, 30% and 50% EGR-rates were obtained by means of two CCD cameras, in the absence of external illumination, with and without interference filters in the optical path. Analysis of these images has revealed that increased EGR rates lead to increased cyclic pressure variations during the warm-up period of the engine, reduced and more fragmented high-temperature regions, reduced flame core temperatures, generally reduced soot oxidation rates but similar ignition delay times.

The spray development, combustion and emissions in a 1.9L optical, four-cylinder, direct-injection diesel engine were investigated by means of pressure analysis, high-speed cinematography, the two-colour method and exhaust gas analysis for various levels of exhaust gas recirculation (EGR), three EGR temperatures (uncontrolled, hot and cold) and three fuels (diesel, n-heptane and a two-component fuel 7D3N). Engine operating conditions included 1000 rpm/idle and 2000 rpm/2bar with EGR-rates ranging from 0 to 70%. Independent of rate, EGR was found to have a very small effect on spray angle and spray tip penetration but the auto-ignition sites seemed to increase in size and number at higher EGR-rates with associated reduction in the flame luminosity and flame temperature, by, say, 100K at 50% EGR.

A diesel spray model has been developed and validated against experimental data obtained for different injection and surrounding gas conditions to allow investigation of the relative importance of the different physical processes occurring during the spray development. The model is based on the Eulerian-Lagrangian approximation and the Navier-Stokes equations, simulating the gas motion, are numerically solved on a collocated non-uniform curvilinear non-orthogonal grid, while the spray equation is solved numerically using a Lagrangian particle tracking method. The injection conditions are determined by another recently developed model calculating the flow in the fuel injection system, the sac volume and injection holes area which accounts for the details of the injection velocity, the fuel injection rate per injection hole and occurrence of hole cavitation. Thus, differences between the sprays from inclined multihole injectors can be simulated and analysed.

Direct flame imaging and pressure analysis were applied to the combustion of gasoline and compressed natural gas (CNG) in a single-cylinder, four-valve spark-ignition engine equipped with optical access via quartz windows in the cylinder liner and piston crown. Tests were performed at three engine speed/load conditions and at equivalence ratios of 1.0, 0.9 and 0.8. The four-valve head incorporated two different port geometries, with and without metal sleeves to deflect the intake air flow, in order to investigate the effect of tumble strength on combustion and engine-out emissions of unburned hydrocarbons and NOx. The results showed that sleeving of the intake ports produced a significant increase in IMEP and a reduction in CoV IMEP for both CNG and gasoline, due to the greatly reduced bum duration.

A computer model solving the 1-D flow in a typical fuel injection system for direct-injection diesel engines is presented. A Bosch distributor - type VE pump connected to four Stanadyne pencil - type nozzles has been used to validate the computer model over a wide range of operating conditions. Validation of the developed computer code has been performed for eight representative test cases. The predicted values which were compared with the experimental ones include the pumping chamber pressure, the line pressure, the needle lift and the injection rate. Results using as input the measured pumping chamber pressure are also presented in order to identify the error in the injection rate signal attributed to the difference between the simulated and the experimental pumping chamber pressure. In addition, the total fuel injection quantity for pump speeds between 500 and 2000 rpm and lever positions between 20% to 100% was calculated and compared with measurements.

Motivated by the possibility of future emission regulations based on particle number as well as mass, after-treatment of ultrafine particles by a cordierite wallflow filter has been investigated. In a laboratory simulation, synthetic carbon particles of known size and concentration in air were captured with number-based efficiency exceeding 70% in the 20–100 nm size range. Effects of temperature, up to 400°C, filter loading time and ambient-temperature sample dilution have been quantified. Steady-speed and European drive cycle results for the same filter fitted to a passenger car with gasoline direct-injection engine have shown promising reductions in emissions, except at the highest speed of the cycle.

Measurements of flow, spray, combustion and performance characteristics are reported for a Hydra direct-injection diesel, based on the Ford 2.5 L, engine and equipped with a variable-swirl port, a unit fuel injector and optical access through the liner and piston. The results provide links between the pre-combustion and combustion flow and, at the same time, between purpose-built single-cylinder optical engines and multi-cylinder production engines of nearly identical combustion chamber geometry. In particular, the spray penetration was found to depend on engine speed, rather than load, with velocities up to around 260 m/s at atmospheric pressure and temperature which are reduced by a factor of 2.5 under operating conditions and seem to be unaffected by swirl. The duration of combustion was reduced with increasing swirl and ignition delay increased linearly with engine speed.

An investigation into the spray structure generated by two swirl pressure atomisers under various operating conditions in a constant-volume chamber and the in-cylinder flow pattern in an optical research direct-injection gasoline engine has been performed using CCD camera and laser Doppler velocimetry, respectively. The results provided detailed information about the effect of back pressure on the spray structure generated by the two injectors and the in-cylinder flow field which the sprays encounter following fuel injection into the cylinder during the induction and compression strokes.

The in-cylinder flow, mixture distribution, combustion and exhaust emissions in a research, five-valve purpose-built gasoline engine are discussed on the basis of measurements obtained using laser Doppler velocimetry (LDV), fast spark-plug hydrocarbon sampling, flame imaging and NOx/HC emissions using fast chemiluminescent and flame ionisation detectors/analysers. These measurements have been complemented by steady flow testing of various cylinder head configurations, involving single- and three-valve operation, in terms of flow capacity and in-cylinder tumble strength.

Transient behavior of the engine is one of the most crucial factors for motorcycle features. Characterization of the fuel film with port fuel injection (PFI) is necessary to enhance this feature with keeping others, such as high output, low emissions and good fuel consumption. In order to resolve the complicated phenomena in real engine condition into simple physical issues, a simulated intake port was used in our research with Laser Induced Fluorescence (LIF) technique to allow accurate measurement of the fuel film thickness, complemented by visualization of the film development and spray behavior using high-speed video imaging. Useful results have been conducted from the parametric studies with various sets of conditions, such as injection quantity, air velocity and port backpressure.

The effect of fuel injection on the flow and the spray/swirl and spray/piston interactions in direct-injection diesel engines have been investigated by simulating diesel sprays with gaseous jet(s) injected through centrally located, single- and multi-hole nozzles into the quiescent and swirling air of a motored engine running at 200rpm and incorporating a flat piston and a re-entrant piston-bowl. The axisymmetric velocity field with and without ‘fuel’ injection was characterised by laser velocimetry near TDC of compression in terms of spatially-resolved ensemble-averaged axial and swirl velocities, the ‘fuel’ concentration field was quantified by laser Rayleigh scattering and the two-dimensional flow was visualised by gated still photography using hollow microballoons as light scatterers.

In an attempt to study the numerous contributors towards cyclic variations in combustion in a direct injection spark ignition engine, simultaneous high-speed imaging of fuel injection and flame growth are undertaken on a crank-angle resolved basis in a single-cylinder optical research engine. Batches of images from 100 consecutive cycles are acquired for all conditions with synchronised in-cylinder pressure logging. The engine is motored and fired at stoichiometric conditions at 1500 RPM under part-load and wide-open-throttle conditions (0.5-1.0 bar intake pressure), with injection timing set early in the intake stroke to promote homogeneous mixture formation with a centrally mounted multi-hole injector. Liquid impingement is observed on the cylinder walls and on the piston crown with early intake injection and multiple injection strategies are employed in an attempt to reduce impingement and alter mixture preparation and subsequent combustion.

A one-dimensional, transient and compressible flow model was used in order to simulate the flow and pressure distribution in advanced high-pressure fuel injection systems; these include electronic distributor-type pumps with either axial or radial plungers and a common-rail system. Experimental data for the line pressure, needle lift, injection rate and total fuel injection quantity obtained over a wide range of operating conditions (from idle to high speed/full load) were used to validate the model. The FIE system used for validation comprised an electronic high-pressure pump connected to two-stage injectors of different type including 6-hole vertical and 5-hole inclined conical-sac and VCO nozzles.

A new simulation approach to the modeling of the whole fuel injection process within a common-rail fuel injection system for direct-injection gasoline engines, including the pressure-swirl atomizer and the conical hollow-cone spray formed at the nozzle exit, is presented. The flow development in the common-rail fuel injection system is simulated using an 1-D model which accounts for the wave dynamics within the system and predicts the actual injection pressure and injection rate throughout the nozzle. The details of the flow inside its various flow passages and the discharge hole of the pressure-swirl atomizer are investigated using a two-phase CFD model which calculates the location of the liquid-gas interface using the VOF method and estimates the transient formation of the liquid film developing on the walls of the discharge hole due to the centrifugal forces acting on the swirling fluid.

A combined two-phase CFD nozzle model and 1-D fuel injection system model is used to predict the flow development inside the discharge hole of a pressure-swirl atomizer connected to a common-rail based fuel injection system for DISI engines. The fuel injection model accounts for the transient pressure pulses developing inside the common-rail and the injector upstream of the nozzle tip and predicts the fuel injection rate through the nozzle. This is then used as input to a 3-D single-phase CFD model estimating the transient development of the swirl velocity inside the pressure-swirl atomizer, as a function of the geometric characteristics of nozzle.