An integration study was performed coupling an SP-100 reactor with either a Brayton or Stirling power conversion subsystem. A power level of 100 kWe was selected for the study. The power system was to be compatible with both the lunar and Mars surface environment and require no site preparation. In addition, the reactor was to have integral shielding and be completely self-contained, including its own auxiliary power for start-up. Initial reliability studies were performed to determine power conversion redundancy and engine module size. Previous studies were used to select the power conversion optimum operating conditions (ratio of hot-side temperature to cold-side temperature). Results of the study indicated that either the Brayton or Stirling power conversion subsystems could be integrated with the SP-100 reactor for either a lunar or Mars surface power application.
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance and arcing.
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance and arcing.
Inverters are solid state devices which change DC to 120VAC electricity. They are sufficiently rugged and reliable to make them practical for use on utility vehicles for operating thumpers, tools, lights and induction motor loads. The SCR type rather than the transistor type inverter is generally required for inductive and reactive loads. Static inverters operate from battery input. They provide power without running an engine, but are limited by battery capacity so work best in intermittent load applications. Dynamic inverters operate from alternator input and will handle continuous loads to 7200 watts with truck engine running.
This paper describes the concept, design, and options of a new power shift transmission family for industrial equipment in the 50-100 hp range. The converter, clutch, and gearing arrangements provide the basis for various transmission configurations with both a drop and straight through output. The designs allow multiple usage of components within a transmission and between different sizes of transmissions. The various gearing, bearing, and clutch designs are based on proved experience factors, and as such will provide a new reliable family of transmissions.
The phenomenal success of the small car is leading to many engineering changes in the automobile industry. It has brought increased emphasis on weight reduction on both small and full-size cars. Improving reliability and designing to eliminate grease fittings have also become important objectives.
Governmental assurance documentation bibliography updated; new tabulation effective as of April 1, 1967. Latest revision indicated in all instances, but no attempt was made to list supplements or amendments. Department of Defense Index of Specifications and Standards (DODISS) published annually in three parts (alphabetic, numerical, and listing of Federal Supply Classification following unclassified documents.
The energy-absorbing bumper system designed for the 1974 Volkswagen in described. Theoretical requirements in bumper design are explained, with emphasis on bumper height, energy tolerance needs, energy absorption, and systems for absorbing the energy involved. The six systems studied are assessed, and the final design chosen is explained. The paper also compares bumper requirements as specified in Europe and the United States.
This paper describes Programmed Ride Control (PRC), the automatic adjustable shock absorber system designed and patented by Ford Motor Company. The system utilizes low shock absorber damping under normal driving conditions to provide soft boulevard ride, automatically switching to firm damping when required for improved handling. The system's microprocessor control module “learns” where the straight ahead steering wheel position is, allowing the system to respond to absolute steering wheel angle. A closed loop control strategy is used to improve system reliability and to notify the driver in the event of a system malfunction. Fast acting rotary solenoids control the damping rate of the shock absorbers.
This paper will identify the role of the engineer in the Total Quality Management movement. In the latter 1980's quality and reliability were identified as being a result of good business practices, rather than only being effected by manufacturing and design systems. In the past, engineers were given total design responsibility with little or no control once the design left their hands. Product cost analysis recently identified approximately 65% of product cost comes from areas which the engineer cannot control. This paper will show how the skills of the engineer are being integrated into the total business environment through a structured planning system, resulting in products and services with customer focus. Quality and reliability in the 1990's will be a result of this well defined and applied business system.
An expansion tank is an integral part of an automotive engine cooling system. The primary function of the expansion tank is to allow the thermal expansion of the coolant. The expansion tank will be referred as hot bottle in this paper. In the System level modeling of the engine internal flow, it is imperative to accurately model and characterize the components in the system. It is often challenging to define the hot bottle accurately with limited parameters in the 1D modeling. Currently it is very difficult to optimize the system by testing. Since testing consumes a lot of time and changes in development stage. If the hot bottle component is not defined properly in the system network, then the system flow balancing cannot be predicted accurately. In this paper, the approach of creating a 1D modeling tool for hot bottle flow prediction is discussed and the simulation results are compared with the physical test data.
This paper discusses the methodology setup for grill opening area prediction at the early development phase of the product development lifecycle, using a commercially available 1D simulation tool- AMESIM. Representative under hood has been modeled using Grill, Condenser, Radiator, intercooler, fan, and engine components. Vehicle velocity is used as an input to derive the airflow passing through the grill and other under-hood components based on ram air coefficient, pressure drop through different components (Grill, Heat exchanger, Fan & Engine). This airflow is used to predict the top tank temperature of the radiator. Derived airflow is correlated with airflow obtained from CFD simulation. A balance has been achieved between cooling drag & fan power consumption at different grill opening areas for target top tank temperature. Top tank temperature has been predicted at two different extreme engine heat rejection operating points.
The potential contributions of acoustical technology to manufacturing companies pervade nearly all of its functions from marketing and product planning to design engineering and quality control. Despite this, however, companies generally feel uneasy when they embark on programs to use acoustics in their operations because the technology seems complicated and somehow harder to “get a handle on” than it is in other cases. But the issues of product sound, and the benefits of acoustics on a diagnostic tool are too important to ignore, so in this paper we discuss these issues in a “20 questions” format to help planners, engineers and managers as they proceed to implement acoustical technology in their organizations.
COMVEC™ conference is the only North American event that addresses vehicles and equipment spanning on-highway, off-highway, agricultural, construction, industrial, military, and mining sectors.
To effectively utilize larger trucks (85 ton and up), open-pit mines and quarries need a larger front-end loader with high reliability and performance. This paper describes the design approach and tests carried out to design 21 cubic yard 580 PAY® loader to meet these requirements. Long fatigue life of structures was obtained by use of full penetration welds. New concept for power control was designed to effectively distribute power between hydraulics and drive train. Spring applied - pressure released brakes were designed into the axle. Tests were carried out in our laboratory and proving grounds to determine performance and reliability.
This paper describes the after-treatment technology that could be used to meet a future BS-VII standard, considering close-coupled SCR (cc-SCR) to help start NOx conversion earlier. Both active (Cu/Fe-SCR based) and passive (V-SCR based) systems have the potential to meet emission limits. V-SCR may be considered in the rear position because V-SCR shows a fast response with very low N2O formation. Next-gen V-SCR technology shows significantly improved performance and durability closer to Cu-SCR. The steady-state NOx conversions over Next-Gen V-SCR were better than BS-VI V-SCR in both fresh and aged-580°C/100h conditions. High durability was also observed after engine aging of 1000h (WHTC + high load). Another big challenge in BS VII could be the PN10 requirement. With enhanced filtration coating (EFC) technology, PN emissions drop drastically in comparison to Euro VI reference without EFC to meet a future BS VII.