Search Results

Fault diagnosis for automotive systems is driven by government regulations, vehicle repairability, and customer satisfaction. Several methods have been developed to detect and isolate faults in automotive systems, subsystems and components with special emphasis on those faults that affect the exhaust gas emission levels. Limit checks, model-based, and knowledge-based methods are applied for diagnosing malfunctions in emission control systems. Incipient and partial faults may be hard to detect when using a detection scheme that implements any of the previously mentioned methods individually; the integration of model-based and knowledge-based diagnostic methods may provide a more robust approach. In the present paper, use is made of fuzzy residual evaluation and of a fuzzy expert system to improve the performance of a fault detection method based on a mathematical model of the engine.

The introduction of advanced electronic controls in passenger vehicles over the last decade has made traditional diagnostic methods inadequate to satisfy on- and off-board diagnostic needs. Due to the complexity of today's automotive control systems, it is imperative that appropriate diagnostic tools be developed that are capable of satisfying current and projected service and on-board requirements. The performance of available diagnostic and test equipment is still amenable to further improvement, especially as it pertains to the diagnosis of incipient and intermittent faults. It is our contention that significant improvement is possible in these areas. This paper briefly summarizes the evolution of on- and off-board diagnostic tools documented in the published literature, with the aim of giving the reader an understanding of their capabilities and limitations, and it further proposes alternative solutions that may be adopted as a basis for an advanced diagnostic instrument.

Over the years numerous researchers have suggested that the ionization current signal carries within it combustion relevant information. The possibility of using this signal for diagnostics and control provides motivation for continued research in this area. To be able to use the ion current signal for feedback control a reliable estimate of some combustion related parameter is necessary and therein lies the difficulty. Given the nature of the ion current signal this is not a trivial task. Fei An et al. [1] employed PCA for feature extraction and then used these feature vectors to design a neural network based classifier for the estimation of air to fuel ratio (AFR). Although the classifier predicted AFR with sufficient reliability, a major draw back was that the ion current signals used for prediction were averaged signals thus precluding a cycle to cycle estimate of AFR.

New vehicle technologies open up a vast number of new options for the designer, removing traditional constraints. Though hybrid powertrains have thus far been implemented chiefly to improve the fuel economy of already economical passenger cars, hybrid technology may have even more to offer in a performance vehicle. In the year when the C6 Corvette and two large GM hybrid projects have been unveiled, a new case study looks to combine these ideas and explore the performance limits for the next generation high performance sports car. Through an innovative transmission concept and thoughtful packaging, the next generation Corvette could enhance a 600 HP spark-ignited V-8 (supercharged LS2) with 1200 HP from electric machines, and still meet current emission standards. Such immense tractive power, however, would be useless without an intelligent means of delivering this power to the wheels.

Due to the stringent emission regulations, On-Board Diagnostics II (OBD II) and the requirement of enhanced evaporative emissions test procedure, an aggressive canister purge control strategy is required for automotive vehicles. The enhanced evaporative emissions test procedure has forced car manufacturer to purge the carbon canister in the vehicle idle condition so that production vehicles meet the SHED and hot soak test requirements. This not only worsens the idle speed quality but also tends to increase exhaust emission levels. Using analytical models of evaporative air and fuel, feed-forward control strategy for both idle by-pass air and air to fuel ratio can be improved. This paper demonstrates an application of evaporative system modeling to the idle air and air to fuel ratio control.

This paper shall present the design and development of a family of high power, high-speed transport and combat vehicles based on a common module. The system looks to maximize performance at both high-speed operation and low-speed, heavy/severe-duty operation. All-wheel drive/steer-by-wire autonomous traction modules provide the basis for the vehicle family. Each module can continuously develop 300-400 kW of power at the wheels and has nearly double peak capability, exploiting the flexibility of the electric traction system. The maximum starting tractive effort developed by one module can reach 10-15 tons, and the full rated power can be produced at speeds of 100 mph. This paper will present the design and layout of the autonomous modules. Details will be provided about the tandem electric axles, with electric differentials and independent steering.

For simulation and analysis of vehicles there is a need to have a means of generating drive cycles which have properties similar to real world driving. A method is presented which uses measured vehicle speed from a number of vehicles to generate a Markov chain model. This Markov chain model is capable of generating drive cycles which match the statistics of the original data set. This Markov model is then used in an iterative fashion to generate drive cycles which match constraints imposed by the user. These constraints could include factors such number of stops, total distance, average speed, or maximum speed. In this paper, systematic analysis was done for a PHEV fleet which consists of 9 PHEVs that were instrumented using data loggers for a period of approximately two years. Statistical analysis using principal component analysis and a clustering approach was carried out for the real world velocity profiles.

This paper reviews existing approaches to the estimation of the state of wear of an automotive damper, with the aim of developing a methodology for a quick and effective diagnostic procedure that could be carried out in any repair facility. It has always been desirable to leave the shock absorber in place at the time of such testing, and there are three general procedures that claim to be effective at determining damper wear. This research investigates a method of controlling a short drop of each corner of the vehicle while measuring the acceleration. The acceleration data is then analyzed with the aim of estimating the decay rate of the resulting oscillation, which is known to be related to the damping ratio of the suspension system. The rate of decay is then used to infer the condition of the vehicles damper. The paper reviews the state of the art, describes the methodology and presents experimental validation of a new concept.

Traditionally in the United States, Diesel engines have negative connotations, primarily due to their association with heavy duty trucks, which are wrongly characterized as “dirty.” Diesel engines are more energy efficient and produce less carbon dioxide than gasoline engines, but their particulate and NOx emissions are more difficult to reduce than spark ignition engines. To tackle this problem, a number of after-treatment technologies are available, such as Diesel Lean NOx Traps (LNTs)), which reduces oxides of nitrogen, and the Diesel particulate filter (DPF), which reduces particulate matter. Sophisticated control techniques are at the heart of these technologies, thus making Diesel engines run cleaner. Another potentially unattractive aspect of Diesel engines is noise.

The process of incorporating the spark plug as a combustion probe, to perform misfire and knock detection, air to fuel ratio and spark timing control has been the subject of research for some time now. [3], [4]. The feasibility of the approach however depends on being able to correlate some characteristic of the ion current signal to the in cylinder combustion process. Shimaski et al. [3] and Miyata et al. [4] suggest such a relationship. The objective of this research has been to extract combustion information from the measured ion current flowing between spark plug electrodes by using various advanced signal processing methods, and to develop a methodology that will permit combustion diagnostics and possibly control based on these measurements. Tests were carried out on a single-cylinder, methane-fueled CFR engine.

Emissions and fuel economy certification testing for vehicles is carried out on a chassis dynamometer using standard test procedures. The vehicle coastdown method (SAE J2263) used to experimentally measure the road load of a vehicle for certification testing is a time-consuming procedure considering the high number of distinct variants of a vehicle family produced by an automaker today. Moreover, test-to-test repeatability is compromised by environmental conditions: wind, pressure, temperature, track surface condition, etc., while vehicle shape, driveline type, transmission type, etc. are some factors that lead to vehicle-to-vehicle variation. Controlled lab tests are employed to determine individual road load components: tire rolling resistance (SAE J2452), aerodynamic drag (wind tunnels), and driveline parasitic loss (dynamometer in a driveline friction measurement lab). These individual components are added to obtain a road load model to be applied on a chassis dynamometer.

Building and testing of physical prototypes for optimization purposes consume significant amount of time, manpower and financial resources. Mathematical formulation and solution of vehicle multibody dynamics equations are also not feasible because of the massive size of the problem. This paper proposes a methodology for vehicle design optimization that does not involve physical prototyping or exhaustive mathematics. The proposed method is fast, cost effective and saves considerable manpower. The methodology uses an industry acknowledged multibody dynamics simulation software (ADAMS) and a flexible architecture to explore large design spaces.

In recent years considerable interest has been placed on the detection of engine misfire. As part of the California Air Resources Board on-board diagnostics regulations for 1994 model year vehicles, misfire should be monitored continuously by the engine diagnostic system. It is expected that the next generation of on-board diagnostics regulations will demand monitoring of partial misfire as well. Several solutions to the misfire detection problem have been proposed and demonstrated for the detection of complete misfires. However, the performance of these methods in the presence of partial misfire is not altogether clear. The aim of this paper is to evaluate the performance of various misfire detection indices, all based on a measurement of crankshaft angular velocity, in the presence of partial misfire. The proposed algorithms are compared to a standard based on a measurement of indicated pressure.

A methodology has been developed to generate military vehicle driving cycles for use in vehicle simulation models. This methodology is based upon the mission profile for a vehicle, which is typically given within a vehicle's specifications and lists the types of terrains that the vehicle is likely to encounter. A simplistic vehicle powertrain and road load model and the Bekker vehicle-soil interaction model are used to estimate the vehicle performance over each type of terrain. Two types of driving cycles are generated within a Graphical User Interface developed within MATLAB using the results of the vehicle models: Linear modes driving cycles, and Real-world driving cycles.

Research has been conducted to develop a methodology for the generation of driving and duty cycles for refuse vehicles in conjunction with a larger effort in the design of a hybrid-electric refuse vehicle. This methodology includes the definition of real-world data that was collected, as well as a data analysis procedure based on sequencing of the collected data into micro-trips and hydraulic cycles. The methodology then applies multi-variate statistical analysis techniques to the sequences for classification. Finally, driving and duty cycles are generated based on matching the statistical metrics and distributions of the generated cycles to the collected database. Simulated vehicle fuel economy for these cycles is also compared to measured values.

This paper describes the development and experimental validation of a Plug-in Hybrid Electric Vehicle (PHEV) dynamic simulator that enables development, testing, and calibration of a traction control strategy. EcoCAR 2 is a three-year competition between fifteen North American universities, sponsored by the Department of Energy and General Motors that challenges students to redesign a Chevrolet Malibu to have increased fuel economy and decreased emissions while maintaining safety, performance, and consumer acceptability. The dynamic model is developed specifically for the Ohio State University EcoCAR 2 Team vehicle with a series-parallel PHEV architecture. This architecture features, in the front of the vehicle, an ICE separated from an automated manual transmission with a clutch as well as an electric machine coupled via a belt directly to the input of the transmission. The rear powertrain features another electric machine coupled to a fixed ratio gearbox connected to the wheels.

Electronic throttle control is increasingly being considered as a viable alternative to conventional air management systems in modern spark-ignition engines. In such a scheme, driver throttle commands are interpreted by the powertrain control module together with many other inputs; rather than directly commanding throttle position, the driver is now simply requesting torque - a request that needs to be appropriately interpreted by the control module. Engine management under these conditions will require optimal control of the engine torque required by the various vehicle subsystems, ranging from HVAC, to electrical and hydraulic accessories, to the vehicle itself. In this context, the real-time estimation of engine and load torque can play a very important role, especially if this estimation can be performed using the same signals already available to the powertrain control module.

Engine knock has been recognized as a major problem limiting the development of fuel efficient spark-ignition engines. Detection methods employed in current knock control systems for spark ignition engines use a measurement of engine block vibration tuned to one or more resonance frequencies to extract knock-related information from the engine structural vibration. A major problem in the detection of knock (especially at higher engine speed) in commercial engines is the isolation of the desired signal from the contributions of the components other than those associated with the phenomenon under investigation. This is generally referred to as background noise. It is known that the engine knock resonance frequencies vary due to changes in combustion chamber volume and temperature during the expansion phase. Therefore, we propose an improved knock detection method using joint time-frequency analysis of engine block vibration and pressure signals.

A number of automotive diagnostic equipment and procedures have evolved over the last two decades, leading to two generations of on-board diagnostic requirements (OBDI and OBDII), increasing the number of components and systems to be monitored by the diagnostic tools. The goal of On-Board Diagnostic is to alert the driver to the presence of a malfunction of the emission control system, and to identify the location of the problem in order to assist mechanics in properly performing repairs. The aim of this paper is to suggest a methodology for the development of an Integrated Powertrain Diagnostic System (EPDS) that can combine the information supplied by conventional tailpipe inspection programs with onboard diagnostics to provide fast and reliable diagnosis of malfunctions.

This paper discusses the use of intelligent control techniques for the control of a parallel hybrid electric vehicle powertrain. Artificial neural networks and fuzzy logic are used to implement a load leveling strategy. The resulting vehicle control unit, a supervisory controller, coordinates the powertrain components. The presented controller has the ability to adapt to different drivers and driving cycles. This allows a control strategy which includes both fuel-economy and performance modes. The strategy was implemented on the Ohio State University FutureCar.