Search Results

Conventional methods to measure gas concentrations and, in particular, NO are typically based on sampling by valve, sample treatment and subsequent analysis. These methods suffer low spatial and temporal resolution. The introduction of high energy lasers in combination with fast detection systems allowed to detect the NO distribution inside optically accessible Diesel engines. In this paper, a high spatial and temporal resolution in-situ technique based on ultraviolet - visible absorption spectroscopy is proposed. The characterization of the combustion process by the detection of gaseous compounds from the start of combustion until the exhaust phase was performed. In particular, this technique allows the simultaneous detection of NO and OH absolute concentrations inside an optically accessible Diesel combustion chamber.

This paper reports the study of the effects of alternative diesel fuel and the impact for the air-fuel mixture preparation. The injection process characterization has been carried out in a non-evaporative high-density environment in order to measure the fuel injection rate and the spatial and temporal distribution of the fuel. The injection and vaporization processes have been characterized in an optically accessible single cylinder Common Rail diesel engine representing evaporative conditions similar to the real engine. The tests have been performed by means of a Bosch second generation common rail solenoid-driven fuel injection system with a 7-holes nozzle, flow number 440 cc/30s @100bar, 148deg cone opening angle (minisac type). Double injection strategy (pilot+main) has been implemented on the ECUs corresponding to operative running conditions of the commercial EURO 5 diesel engine.

This paper illustrates the results of an experimental characterization of a high pressure diesel spray injected by a common rail (CR) injection system both under non-evaporative and evaporative conditions. Tests have been made injecting the fuel with a single hole injector having a diameter of 0.18 mm with L/D=5.56. The fuel has been sprayed at 60, 90 and 120 MPa, with an ambient pressure ranging between 1.2 to 5.0 MPa. The spray evolution has been investigated, by the Mie scattering technique, illuminating the fuel jet and acquiring single shot images by a CCD camera. Tests under non-evaporative conditions have been carried out in an optically accessible high pressure vessel filled with inert gas (N2) at diesel-like density conditions. The instantaneous fuel injection rate, obtained with a time resolution of 10 microseconds, has been also evaluated by an AVL Fuel Meter working on the Bosch Tube principle.

In-cylinder measurements of turbulent integral length scales, carried out during the last 60 degrees of the compression stroke at 600 and 1,000 rpm by a two-probe volume LDV system, were used to assess the capability of the k-ε model used in KIVA-II code. The objective of the paper is to address the following question: what is the most reasonable definition of turbulent length scale in the k-ε model for engine applications? The answer derived from the comparison between KIVA predictions and experiments that showed a fair agreement between the computed turbulent length scale and the measured lateral integral length scale. The agreement is a result of proper choice of the initial swirl ratio and turbulent kinetic energy at inlet valve closure (IVC) by taking into account the LDV measurements and the value of the constant Cμε in the k-ε model equations that relates the turbulent length scale to k and ε.

Aim of this work is to develop a general purpose model for combustion and knocking prediction in SI engines, by coupling a thermo-fluid dynamic model for engine simulation with a general detailed kinetic scheme, including the low-temperature oxidation mechanism, for the prediction of the auto-ignition behavior of hydrocarbons. A quasi-D approach is used to describe the in-cylinder thermodynamic processes, applying the conservation of mass and energy over the cylinder volume, modeled as a single open system. The complex chemistry model has been embedded into the code, by using the same integration algorithm for the conservation equations and the reacting species, and taking into account their mutual interaction in the energy balance. A flame area evolution predictive approach is used to evaluate the turbulent flame front propagation as function of the engine operating parameters.

The behaviour of two combustion chambers, a toroidal and a turbulent one, has been compared. The engine performance in terms of imep and exhaust emissions were measured. Laser Doppler Anemometry technique was used to characterize the fluids dynamic aspect of combustion system. The axial asymmetry introduced in combustion chamber shape causes strong differences in the air flow field at the end of compression stroke. The tangential velocity profile is flattened to that obtained with toroidal chamber. Moreover the rms values of tangential velocity measured in turbulent combustion chamber are about three times higher than that measured in the toroidal chamber. At low engine speed the turbulent chamber allows to operate with low NOx levels without penalties of smoke emissions and fuel consumption as happens by using conventional toroidal chamber.

A satisfactory answer to the future severe normative on emissions and to the market request for spark ignition engines seems to be the use of downsized engines for passenger cars. Downsizing permits the increase in engines power and torque without the increase in cylinder capacity. The downsizing benefits are evident at part loads; on the other hand, more work should be done to optimize boosted engines at higher and full load. To this goal, a detailed knowledge of the thermo-fluid dynamic processes that occur in the combustion chamber is fundamental. The aim of this paper is the experimental investigation of the effect of the fuel injection in the intake manifold on the combustion process and pollutant formation in a boosted spark ignition (SI) engine. The experiments were performed on a partially transparent single-cylinder port fuel injection (PFI) SI engine, equipped with a four-valve head and boost device.

LDV measurements of the tangential component of the flow field velocity within the cylinder of a motored, real diesel engine are reported. A comparison of the fluid-dynamic behavior between toroidal and four-lobes square combustion chambers is shown. Tests were carried out over a range of engine speed of 500 and 1500 rpm. An ensemble-average data processing technique was used to analyze the velocity data recorded at 30 CAD BTDC and at TDC during compression stroke. The measurements were made at a depth of 3.0 mm from the piston head in two axial sections of the four-lobe combustion chamber. The results show that the four-lobe, square combustion chamber reduces the bulk swirl and increases the turbulence at the two engine speeds. The square cup transforms more of the kinetic energy of the bulk flows into turbulent kinetic energy than toroidal cup. At TDC the tangential velocity profile tends to solid body along the short section and to flat profile along the long section.

The present paper reports the results of an experimental investigation carried out on a four-stroke single- cylinder D.I. diesel engine (100 x 95mm bore x stroke) with the aim to evaluate the effects of a four-lobe square combustion chamber on the gaseous and particulate emissions. Fluid-dynamic behaviour of the axisymmetric toroidal and four-lobe square chambers was investigated by Laser Doppler Anemometry. Engine tests at 2000 and 3000 rpm for different start of combustion (SOC) and A/F ratio are reported. Particulate, HC and NOx emission index measured under different operating conditions are given. In addition, the volatile content of the particulates produced from the two chambers at various engine operative conditions was measured by thermogravimetric analysis (TGA). Finally, the catalytic activity of a metal-oxide-based catalyst in the combustion of particulate was also evaluated by TGA.

This paper illustrates the results of an experimental investigation on the liquid fuel spray from a multi-jet common rail injection system both under non evaporative and evaporative conditions. Tests have been taken using a 5 hole, 0.13 mm diameter, 150° spray angle, micro-sac nozzle having a flow rate of 270 cm3/30 sec@10 MPa exploring different injection strategies. Experiments have been taken, under non evaporative conditions, injecting the fuel within stagnant inert gas, at different density, in a high-pressure optically-accessible cylindrical vessel with three large quartz windows. Under evaporative conditions, the experiments have been taken within a crank-case scavenged single-cylinder 2-stroke direct injection Diesel engine provided of optical accesses to the combustion chamber. It allows to study the fuel injection process under thermodynamic conditions similar to those currently reached in modern direct injection diesel engines.

The growing demands on fuel economy and always stricter limitations on pollutant emissions has increased the interest in the ignition phenomena to guarantee successful flame development for all the spark ignition (SI) engine operating conditions. The initial size and the growth of the flame have a strong influence on the further development of the combustion process. In particular, for the new FIAT generation of turbocharged SI engines, the first times of spark ignition combustion are not yet fully understood. This is mainly due to the missing knowledge concerning the detailed physical and chemical processes taking place during the all set of the flame propagation. These processes often occur simultaneously, making difficult the interpretation of measurements. In the present paper, flame dynamic was followed by UV-visible emission imaging in an optical SI engine.

The influence of fuel composition on mixture formation and first stage of combustion, occurring in a small high swirl combustion chamber of an IDI Diesel engine, was analyzed from measurements of spectral extinction and flame emissivity. Measurements were carried out in an optically accessible combustion chamber in which an air swirling flow is forced from the main chamber through a tangential passage. A conventional injection system was used to inject Tetradecane, N-heptane and Diesel fuel. The distribution of liquid and vapor and the interaction of the jet with air swirl were detected by UV-visible extinction measurements. The autoignition phase was characterized by UV-visible chemiluminescence measurements. For all fuels examined, it was observed that initially the liquid fuel penetrates almost linearly with time until reaching a maximum characteristic length, slightly dependent on the fuel.

Improvement of combustion system for low emissions of a single cylinder diesel engine is presented. In particular the effects of spray angle, holes diameter and number, compression ratio and combustion chamber geometry on engine performance and emissions are evaluated. The fluid-dynamic behaviour of combustion system is analyzed by LDA technique. Engine tests have been carried out at two engine speed and at different start of combustion. The particulate matter has been analyzed in terms of soluble organic fraction and dry soot.

The fluid-mechanic behaviour of straight-sided and re-entrant chamber geometries has been studied using laser doppler anemometry (LDA) technique. Measurements have been carried out during the compression stroke in a direct injection diesel engine, representative of medium size family, operating at 1000 rpm under motored conditions. The mean motion and turbulence intensity have been computed using a filtering procedure on the LDA data. Using the second version of KIVA code, the air flow field evolution during the same crank angle period has been also computed. To perform proper comparisons between measured and computed values of mean velocity and turbulence intensity, a careful choice of the initial conditions for computations has been performed. Reasonable agreement has been found between computed and measured mean swirl velocities for both combustion chamber geometries tested. On the contrary, the computed turbulence intensities underestimate those measured.

The optimization of combustion system of a single-cylinder d.i. diesel engine, representative of heavy-duty family, is discussed. The characterization of in-cylinder fluid motion of a conventional straight-sided and a re-entrant combustion chamber, carried out by LDA technique, is presented. Engine tests, using the same chambers and sacless nozzles with different holes diameter and appropriate spray angle, have been performed. Strong reduction of smoke and HC emissions has been obtained, remaining unchanged the engine performance.

The aim of the present paper is to provide an insight into the fluid dynamic processes that occur during the air/fuel mixture formation period in direct injection diesel engines. An experimental and numerical investigation has been performed to analyse the mixing process between an evaporating diesel spray and a swirl air flow under realistic engine conditions. Experimental tests have been carried out spraying the fuel within an optically accessible prototype 2-stroke Diesel engine equipped with an external combustion chamber having cylindrical shape. The intake air flow, coming from the engine cylinder, is forced within the combustion chamber by means of a tangential duct generating a well structured swirl flow similar to that developing in a real light duty diesel engine with a high swirl ratio. A micro-sac 5-hole, 0.13 mm diameter, 150° spray angle electro-hydraulic injector supplies the fuel by a common rail injection system able to manage multiple injection strategies.

The paper aims at providing information about the spray structure and its evolution within the combustion chamber of a heavy duty direct injection (HDDI) diesel engine. The spray penetration is investigated, firstly under quiescent conditions, injecting the fuel in a vessel under ambient temperature and controlled back pressure by both numerical and experimental analyses using the STAR-CD code and the imaging technique, respectively. Experimental results of fuel injection rate, fuel penetration, and spray cone angle are used as initial conditions to the code and for the comparison of predictions. The experimental investigation is carried out using a mechanical injection pump equipped by the heavy duty eight cylinder engine. Only one of its plungers has been activated and the fuel is discharged through a seven holes mechanical injector, 0.40 mm in diameter.

Tangential component of velocity and turbulence were measured in three locations in the re-entrant combustion chamber of a motored single-cylinder d.i. Diesel engine (0.435 liter, 21:1 compression ratio) using a Laser Doppler Velocimetry system. Moreover, a modified LDV system with two-probe volume was used to measure directly lateral integral length scales of the velocity tangential component at two engine speeds. The measurements were made on a horizontal plane at 5 mm below the engine head from 100 degrees before TDC to 60 degrees after TDC of both the compression and expansion strokes. The engine was motored at 1,000 and 1,500 rpm respectively. An ensemble-averaging technique was performed to analyze the instantaneous velocity information supplied by two Burst Spectrum Analyzers. The lateral integral length scale was obtained from the integral of the spatial correlation coefficient of the velocity fluctuation for different separation.

Quantitative measurements of the soot volume fraction and diameter performed by spectroscopic techniques within the combustion chamber of a diesel engine are employed to aid multidimensional simulation of the soot formation and oxidation processes. By changing the start of fuel injection, two different operating conditions are considered, which are characterized by different relative importance of the premixed to the diffusive stage of the combustion process. Both the reduced models by Hiroyasu et al., and the one by Nagle and Strikland- Constable are employed within the numerical simulation. The reason of the peculiar over-prediction of soot concentration of the latter model is discussed and related to the need of furnishing coherent values of the soot particle density and mean diameter.

Multidimensional simulation of the soot formation process in a diesel engine is realised exploiting quantitative measurements of the soot volume fraction and diameter obtained by optical techniques. Broadband extinction and scattering measurements are performed on an optically accessible 4-stroke engine where a forced air motion allows a strong prevalence of the premixed stage of combustion with respect to the non-premixed one. Two semi-empirical models for soot formation are tested in the numerical simulation, which is performed using a customized version of the KIVA-3 code. The need of furnishing coherent values of the soot particles density and mean diameter to the one of the two models requiring this kind of information, is highlighted and demonstrated to be crucial in avoiding over-prediction of the soot concentration.