Search Results

A combined biodynamic and vehicle model is used to assess the vibration and performance of a human operator performing driving and other tasks. The other tasks include reaching, pointing and tracking by the driver and/or passenger. This analysis requires the coordinated use of separate and mature software programs for anthropometrics, vehicle dynamics, biodynamics, and systems analysis. The total package is called AVB-DYN, an acronym for Anthropometrics, Vehicle and Bio-DYNamics. The biodynamic component of AVB-DYN is described, and then compared with an experiment that studied human operator in-vehicle reaching performance using the U.S. Army TACOM Ride Motion Simulator.

Ground vehicle dynamic stability, including spinout and rollover, is highly dependent on maneuvering conditions and the nonlinear force response characteristics of tires. Depending on vehicle configuration, unstable behavior requires high, sustained lateral acceleration, and some maneuver induced excitation of the roll and yaw mode dynamics. Dynamic instability in some vehicles can be induced by a steering reversal maneuver that involves sustained limit performance lateral acceleration. Using a validated vehicle dynamics simulation, analysis is presented to illustrate what constitutes a critical stability sensitive maneuver. Two example test cases are used to show that a critical stability sensitive maneuver must be more severe than a single lane change. Even reaching tire saturation limits during an aggressive single lane change does not give the sustained lateral acceleration required to provoke instability conditions.

This paper describes a low cost, PC based driving simulation that includes a complete vehicle dynamics model (VDM), photo realistic visual display, torque feedback for steering feel and realistic sound generation. The VDM runs in real-time on Intel based PCs. The model, referred to as VDANL (Vehicle Dynamics Analysis, Non-Linear) has been developed and validated for a range of vehicles over the last decade and has been previously used for computer simulation analysis. The model's lateral and longitudinal dynamics have 17 degrees of freedom for a single unit vehicle and 33 degrees of freedom for an articulated vehicle. The model also includes a complete drive train including engine, transmission and front and rear drive differentials, and complete, power assisted braking and steering systems. A comprehensive tire model (STIREMOD) generates lateral and longitudinal forces and aligning torque based on normal load, camber angle and horizontal (lateral and longitudinal) slip.

This paper presents a methodology for validating vehicle stability and control computer simulations. Validation is defined as showing that, within some specified operating range of the vehicle, a simulation's predictions of a vehicle's responses agree with the actual measured vehicle's responses to within some specified level of accuracy. The method uses repeated experimental runs at each test condition to generate sufficient data for statistical analyses. The acquisition and reduction of experimental data, and the processing path for simulation data, are described. The usefulness of time domain validation for steady state and slowly varying transients is discussed. The importance of frequency domain validation for thoroughly validating a simulation is shown. Both qualitative and quantitative methods for the comparison of the simulation predictions with the actual test measurements are developed.

The need to measure vehicle parameters required for vehicle dynamics simulations has been a difficult and time-consuming task since the first simulations were developed over 35 years ago. The wide variety of simulations developed have demanded as wide a variety of vehicle parameters. Due in part to this diversity, no standard set of measurement techniques has been developed. A laboratory facility to measure the vehicle parameters for a 13-degree-of-freedom, lumped parameter, nonlinear vehicle dynamics simulation (VDANL) was needed. Parameters for a large number of vehicles were required. Therefore, only a few days could be devoted to measuring the parameters for each vehicle. The Composite Parameter Measurement Device (CPMD) was designed and built to meet these goals. The hardware, data acquisition system and analysis software are presented. The roll test, steer test, and aligning stiffness test, used during the initial testing are discussed.

Maneuverable round and ramair parachutes are flown by professional forestry firefighters, search and rescue personnel, and military combat teams when deployment by fixed or rotary aircraft is inappropriate. Parachute flight training requires the development of perceptual skills in canopy control, guidance, and energy management. These parachutists must learn to accurately sense motion visual cues, and predict and manage their trajectory. Parachute guidance and control can only be acquired through repeated practice. Canopy control training has been traditionally limited to a classroom lecture topic. There was no opportunity for the immediate student/instructor dialogue available during the extensive dual flight training used for conventional aircraft, where instruction can occur during the numerous practice landings available via rapid touch-and-go techniques.

The U.S. Army uses the root mean square and power spectral density of elevation to characterize road/terrain (off-road) roughness for durability. This paper describes research aimed toward improving these metrics. The focus is on taking previously developed metrics and applying them to mathematically generated terrains to determine how each metric discerns the relative roughness of the terrains from a vehicle durability perspective. Multiple terrains for each roughness level were evaluated to determine the variability for each terrain rating metric. One method currently under consideration is running a relatively simple, yet vehicle class specific, model over a given terrain and using predicted vehicle response(s) to classify or characterize the terrain.

Lateral/directional dynamics involve vehicle yawing, rolling and lateral translation motions and dynamic stability concerns directional behavior (i.e. spinout) and rollover. Previous research has considered field test and computer simulation methods and results concerning lateral/directional stability. This paper summarizes measurements and simulation analysis of a wide range of vehicles regarding directional and rollover stability. Directional stability is noted to be strongly influenced by lateral load transfer distribution (LTD) between the front and rear axles LTD influences tire side force saturation properties, and should be set up so that side forces at the rear axle do not saturate before the front axle under hard maneuvering conditions in order to avoid limit oversteer and spinout.

A combined biodynamic and vehicle model is used to assess the vibration and performance of a human operator performing driving and other tasks. The other tasks include reaching, pointing and tracking by the driver and/or passenger. This analysis requires the coordinated use of separate and mature software programs for anthropometrics, vehicle dynamics, biodynamics, and systems analysis. The total package is called AVB-DYN, an acronym for Anthropometrics, Vehicle, and Bio-DYNamics. The objectives and architecture are discussed, and then a preliminary version of this package is demonstrated in an example where a HMMWV (High Mobility Multipurpose Wheeled Vehicle) operator is performing a driving task.

Dynamic stability is influenced by vehicle and tire characteristics and operating conditions, including speed and control inputs. Under limit performance operating conditions, maneuvering can force a vehicle into oversteer and high sideslip. The high sideslip results in limit cornering conditions, which might proceed to spinout, or result in tip-up and rollover. Oversteer and spinout result from rear axle tire side force saturation. Tip-up and rollover occur when tire side forces are sufficient to induce lateral acceleration that will overcome the stabilizing moment of vehicle weight. With the use of computer simulation and generic vehicle designs, this paper explores the vehicle and tire characteristics and maneuvering conditions that lead to loss of directional control and potential tip-up and rollover.

As part of the evaluation of vehicle simulation models, a vehicle dynamics engineer typically desires to compare simulation results to test data from actual vehicles and/or results from known, or higher fidelity simulations. Depending on the type of model, several types of tests and/or maneuvers may need to be compared. For military vehicles, there is the additional requirement to run specific types of maneuvers for vehicle model evaluations to ensure that the vehicle complies with procurement requirements. A thorough evaluation will run two different categories of tests/maneuvers. The first category consists of laboratory type tests that include weight distribution, kinematics and compliance, steering ratio, and other static measures. The second category consists of dynamic maneuvers that include handling, drive train, braking, ride, and obstacle types. In this paper, a process for proper evaluation of vehicle simulation models is presented.

This paper describes the driver/vehicle modeling aspects of a computer simulation that can respond to highway engineering descriptions of roadways. The driver model interacts with a complete vehicle dynamics model that has been described previously. The roadway path is described in terms of horizontal and vertical curvature and cross slopes of lanes, shoulders, side slopes and ditches. Terrain queries are made by the vehicle dynamics to locate tires on the roadway cross-section, and to define vehicle path and road curvature at some distance down the road. The driver model controls steering to maintain lateral lane position. Speed is maintained at a speed limit on tangents, and decreased as needed to maintain safe lateral acceleration. Because the bandwidth of longitudinal (speed) control is much lower than lateral/directional (steering) control, the driver model looks further ahead for speed control than for steering.

This paper discusses recent developments and application of driving simulators. Simulation of driving via films has been used for a number of years as a driver education tool. More recently, interactive simulators have been developed for research and training applications. Improvements are accelerating due to a combination of ongoing research needs, and general state of the art advances in hardware and software technology. Modern simulator requirements are reviewed from the point of view of both driver characteristics (vision, audition, proprioception, vestibular motion sensation) and task demands (e.g., steering and speed control, risk perception, decision making, general workload level). A variety of simulator applications are summarized, including comparison with subsequent field tests. These applications include studies involving drunk driving and risk taking, reduced visibility and delineation, and signing.

The paper presents an evaluation of two vehicle dynamics simulations: “Vehicle Dynamics Analysis, Non-Linear” (VDANL) from Systems Technology, Inc. and “Vehicle Dynamics Models for Roadway Analysis and Design” (VDM RoAD) from the University of Michigan Transportation Research Institute. The versions of these simulations are being developed for the Federal Highway Administration (FHWA). Working in cooperation with the FHWA, the National Highway Traffic Safety Administration's (NHTSA) Vehicle Research and Test Center (VRTC) in East Liberty, Ohio, has evaluated these simulations. An extensive vehicle parameter measurement and field testing program has been performed using a 1994 Ford Taurus to provide simulation parameters and to “benchmark” data for the simulation evaluation.

As part of the National Advanced Driving Simulator (NADS) program, the Vehicle Research and Test Center (VRTC) in East Liberty, Ohio is evaluating the NADS vehicle dynamics software. As part of VRTC's effort, an extensive vehicle testing program to provide data for the simulation evaluation was performed. This paper describes VRTC's testing of a 1994 Ford Taurus GL passenger car. Each of the test maneuvers run by the Taurus are described, along with instrumentation setup, control actuation, test conditions, and driver procedures. The test data reduction and processing are detailed. Sample results of the testing and an analysis of test repeatability and measurement noise are also presented.

The U.S. Army uses the root mean square and power spectral density of elevation to characterize road/terrain (off-road) roughness for durability. This paper describes research aimed toward improving these metrics. The focus is on taking previously developed metrics and applying them to mathematically generated terrains to determine how each metric discerns the relative roughness of the terrains from a vehicle durability perspective. Multiple terrains for each roughness level were evaluated to determine the variability for each terrain rating metric. One method currently under consideration is running a relatively simple, yet vehicle class specific, model over a given terrain and using predicted vehicle response(s) to classify or characterize the terrain.

Interactive driving simulation is attractive for a variety of applications, including screening, training and licensing, due to considerations of safety, control and repeatability. However, widespread dissemination of these applications will require modest cost simulator systems. Low cost simulation is possible given the application of PC level technology, which is capable of providing reasonable fidelity in visual, auditory and control feel cuing. This paper describes a PC based simulation with high fidelity vehicle dynamics, which provides an easily programmable visual data base and performance measurement system, and good fidelity auditory and steering torque feel cuing. This simulation has been used in a variety of applications including screening truck drivers for the effects of fatigue, research on real time monitoring for driver drowsiness and measurement of the interference effect of in-vehicle IVHS tasks on driving performance.

Interactive simulation requires providing appropriate sensory cuing and stimulus/response dynamics to the driver. Sensory feedback can include visual, auditory, motion, and proprioceptive cues. Stimulus/response dynamics involve reactions of the feedback cuing to driver control inputs including steering, throttle and brakes. The stimulus/response dynamics include both simulated vehicle dynamics, and the response dynamics of the simulation hardware including computer processing delays. Typically, simulation realism will increase with sensory fidelity and stimulus/response dynamics that are equivalent to real-world conditions (i.e. without excessive time delay or phase lag). This paper discusses requirements for sensory cuing and stimulus/response dynamics in real-time, interactive driving simulation, and describes a modest fixed-base (i.e. no motion) device designed with these considerations in mind.

This paper presents an overview of work performed by the National Highway Traffic Safety Administration's (NHTSA) Vehicle Research and Test Center (VRTC) to test, validate, and improve the planned National Advanced Driving Simulator's (NADS) vehicle dynamics simulation. This vehicle dynamics simulation, called NADSdyna, was developed by the University of Iowa's Center for Computer-Aided Design (CCAD) NADSdyna is based upon CCAD's general purpose, real-time, multi-body dynamics software, referred to as the Real-Time Recursive Dynamics (RTRD), supplemented by vehicle dynamics specific submodules VRTC has “beta tested” NADSdyna, making certain that the software both works as computer code and that it correctly models vehicle dynamics. This paper gives an overview of VRTC's beta test work with NADSdyna. The paper explains the methodology used by VRTC to validate NADSdyna.

This paper presents the development of a tire model for use in the simulation of vehicle dynamics. The model was developed to predict tire lateral and longitudinal force responses to dynamic inputs. In this new tire model, the contact patch of a tire is lumped into a number of elements to study the dynamic behavior of the displacement of the tire contact patch in the lateral and longitudinal directions. For each displacement, a differential equation governing the dynamic behavior of the displacement to the dynamic inputs is derived. Based on the differential equations for the lateral and longitudinal displacements, difference equations are derived for the purpose of simulating tire output responses. Since system parameters, such as mass, damping and stiffness, in the difference equations are unknown, estimation of system parameters is performed using the differential equations and experimental data measured for this research.