Search Results

Measurement of emissions from small utility engines has usually been accomplished using steady-state raw emissions procedures such as SAE Recommended Practice J1088. While raw exhaust measurements have the advantage of producing modal exhaust gas concentration data for design feedback; they are laborious, may influence both engine performance and the emissions themselves, and have no provision for concurrent particulate measurements. It is time to consider a full-dilution procedure similar in principle to automotive and heavy-duty on-highway emission measurement practice, leading to improvements in many of the areas noted above, and generally to much higher confidence in data obtained. When certification and audit of small engine emissions become a reality, a brief dilute exhaust procedure generating only the necessary data will be a tremendous advantage to both manufacturers and regulatory agencies.

Methods for measurement and expression of crankcase or “blowby” emissions from diesels were developed and demonstrated on a test engine. These methods were subsequently used to characterize gas and particulate emissions from two in-service engines. Crankcase emissions were evaluated under engine operating conditions corresponding to the EPA 13-mode certification test. Substances for which analyses were conducted included regulated pollutants, sulfate, trace elements, nitrosamines, individual hydrocarbons, and aldehydes. Emissions from the diesel crankcases were compared to exhaust emissions (where possible) to assess their importance. Analysis for nitrosamines was continued beyond the original effort, utilizing another test engine.

Gaseous and particulate emissions from two heavy-duty diesel engines were characterized while the engines were operated on five different fuels. Characterization included mass rates of major exhaust products, plus analysis of particulate matter for sulfate, trace elements, major elements, total solubles, and other properties. Analysis of rate and composition data was conducted with regard to fuel and engine effects on particulate. Two large particulate samples were also collected for later analysis on groups of organics present.

Emissions from a Stirling engine-powered 1986 model light-duty truck were measured using current EPA (chassis dynamometer) emissions certification procedures and certain specialized tests. Three fuels were used including unleaded gasoline, a blend of MTBE in unleaded gasoline, and JP-4. City (FTP) cycles and Highway (FET) cycles were run on all three fuels, and emissions measured during the cycles included hydrocarbons (HC), carbon monoxide (CO), and oxides of nitrogen (NOx). Fuel economy was also calculated for these tests. Additional pollutants measured during some of the tests included aldehydes, 1,3-butadiene, individual hydrocarbon species, and total particulate matter. In addition to the cyclic schedules, steady-state conditions were run on JP-4 and straight gasoline for regulated emissions and fuel economy. The conditions consisted of several simulated gradients at three vehicle speeds, plus idle.

Particulate and gaseous emissions from two light-duty diesel vehicles were measured over eight operating schedules, using five different fuels. Characterization included regulated exhaust emissions and a number of unregulated constituents. Non-routine gas measurements included phenols, hydrocarbon boiling range, and aldehydes. Particulate characterization included mass rates and concentrations, visible smoke, aerodynamic sizing, total organics, BaP, sulfate, phenols, trace elements, and major elements. Statistical analysis of emissions data was undertaken using fuel properties and operating schedule statistics as independent variables. Regressions were computed for a few variables, and analysis of variance and multiple comparisons were used where the data were not suitable for regression analysis.

Exhaust emission data from several fuel effects studies were normalized and subjected to statistical analyses. The goal of this work was to determine whether emission effects of property variation in alternate-source fuels were similar, less pronounced, or more pronounced than the effects of property variation in petroleum fuels. A literature search was conducted, reviewing hundreds of studies and finally selecting nine which dealt with fuel property effects on emissions. From these studies, 15 test cases were reported. Due to the wide variety of vehicles, fuels, test cycles, and measurement techniques used in the studies, a method to relate them all in terms of general trends was developed. Statistics and methods used included bivariate correlation coefficients, regression analysis, scattergrams and goodness-of-fit determinations.

Diesel-powered cars afford some distinct advantages in fuel economy and certain exhaust emissions relative to the conventional Otto cycle engine. Particulate and sulfate emissions from light-duty diesels are two important unregulated emissions for which little is known. Five diesel-powered, light-duty vehicles, a Peugeot 204D, a Mercedes 240D, a Mercedes 300D, a Comprex-equipped Mercedes 220D, and a Perkins 6-247 powered IH pickup, were used to quantify the range of particulate, sulfate as well as other unregulated emissions of odor, visible smoke, sulfur dioxide, aldehydes, and selected non-reactive hydrocarbons. Three transient driving cycles were employed including that used in emissions certification, sulfate testing, and highway fuel economy. Emission rates of particulate, sulfate, and other contaminants of a regulated and unregulated nature are presented in several ways: mass per unit of time, per unit of fuel consumed, and per unit of distance driven.

Exhaust emissions from in-use diesel trucks and buses can be reduced by application of retrofits consisting of new parts and adjustments. The results of fleet test demonstrations of two retrofit kits, one for 2-stroke diesel-powered buses and the other for 4-stroke diesel trucks, are described. Except for the catalytic muffler, the components and adjustments composing the General Motors environmental improvement proposal kit for General Motors city buses were found helpful in reducing exhaust odor, smoke, and certain gaseous emissions. The turbocharger kit and adjustments marketed by Cummins Engine for its NHC 250, an in-use naturally aspirated truck engine, was likewise found to reduce visible smoke satisfactorily. The fleet test data are from three city buses operated for two years and three intercity truck tractors operated for eight months.

The use of diesel exhaust-emissions measurements to predict the observed odor from diesel engine exhaust has been studied, using a group of 31 trucks and buses powered by a variety of diesel engines. Regression analysis of gaseous emissions at a variety of conditions has resulted in equations for use in predicting odor. Acrolein, carbon dioxide, total hydrocarbons, selected light hydrocarbons, nitric oxide, carbon monoxide, and aliphatic aldehydes have been related to perceived odor. Some of these exhaust products are odorous and some are nonodorous yet indicative of the completeness of combustion. The empirical method, however, is somewhat less reliable than the observed odor based on a trained panel rating supra-threshold levels in terms of the PHS Quality-Intensity Odor Rating kit. In general, the greater variety of measurements and the fewer type of engines will increase odor prediction accuracy.

The design and development of an instrument for the measurement of total hydrocarbons in diesel exhaust are described, and its ability to measure steady-state and transient hydrocarbon emissions is indicated. The two-section system comprises a sampling train and flame-ionization detector and a chromatograph electrometer, recorder and backpressure regulator. A mixture of 40% H2 and 60% He was found to be the best fuel for low O2 response with the system. The method has been used for more than a year in evaluating hydrocarbon emissions from a wide variety of diesel engines under a number of typical operating conditions. The greatest advantage of the high-temperature system is its potential for expressing the total hydrocarbon content in diesel exhaust.

This paper describes experiments to determine the effect on exhaust emissions of starting on compressed natural gas (CNG) and then switching to gasoline once the catalyst reaches operating temperature. Carbon monoxide, oxides of nitrogen, and detailed exhaust hydrocarbon speciation data were obtained for dedicated CNG, then unleaded gasoline, and finally CNG start -gasoline run using the Federal Test Procedure at 24°C and at -7°C. The result was a reduction in emissions from the gasoline baseline, especially at -7°C. It was estimated that CNG start - gasoline run resulted in a 71 percent reduction in potential ozone formation per mile.

Several properties of a refinery “straightrun kerosene“, which had a narrow boiling range approximating the middle of a No. 1 diesel fuel, were altered to study their effects on regulated and unregulated exhaust emissions. Eleven fuel blends, representing changes in nitrogen content, aromatic level, boiling point distribution, olefin content, and cetane number, were evaluated in a 1975 Mercedes-Benz 240D. Statistical analysis, including regression, was performed using selected fuel properties as independent variables. Higher aromatic levels were generally associated with increased emissions, while increased olefin levels were generally associated with decreased emissions.

Recent approval of emission standards for small utility engines by the California Air Resources Board(1)* suggests that substantial reductions in emissions from small utility engines will soon be required. While 1994 standards may be met with simple engine adjustments or modifications, 1999 standards are much more stringent and may require the use of catalysts in conjunction with other emission reduction technologies. Assessing the feasibility of candidate emission control strategies is an important first step. Various emission reduction technologies were applied to three different 4-stroke engines. Emission tests were conducted to determine the effectiveness of air/fuel ratio changes, thermal oxidation, exhaust gas recirculation, and catalytic oxidation with and without supplemental air. Results of these evaluations, along with implications for further work, are presented. One engine's emissions were reduced below the levels of 1999 ARB standards.

A major gap exists in available baseline emissions data on the small utility engine population between the mid-1970's and present day. As part of the input required for a standard-setting process, the California Air Resources Board has funded limited laboratory emission measurements on a number of modern small engines, both 2-stroke and 4-stroke designs. Exhaust constituents characterized in this study include total hydrocarbons, reactive hydrocarbons (RHC), methane, CO, NOx, CO2, O2, aldehydes, and particulate matter. A total of nine engines were evaluated, spanning the range from the smallest widely-used 2-strokes (about 20 cc displacement) to 4-strokes approaching 20 hp.

This paper summarizes an investigation of reductions in exhaust emission levels attainable using various techniques appropriate to gasoline engines used in vehicles over 14,000 lbs GVW. Of the eight gasoline engines investigated, two were evaluated parametrically resulting in an oxidation and reduction catalyst “best combination” configuration. Four of the engines were evaluated in an EGR plus oxidation catalyst configuration, and two involved only baseline tests. Test procedures used in evaluating the six “best combination” configurations include: three engine emission test procedures using an engine dynamometer, a determination of vehicle driveability, and two vehicle emission test procedures using a chassis dynamometer. Dramatic reductions in emissions were attained with the catalyst “best combination” configurations. Engine durability, however, was not investigated.

The advent of diesel-powered versions of production passenger cars signals significant dieselization in the United States. Two vehicles, an experimental Oldsmobile diesel Cutlass and a Volkswagen diesel-powered Rabbit, were evaluated to determine their gaseous, particulate, smoke, odor, and noise emissions. For comparison, a 1977 Oldsmobile Cutlass powered by the 260 CID gasoline engine and a 1.6 liter gasoline fuel injected Volkswagen Rabbit (Calfornia version) were similarly evaluated under most emission categories. Three transient driving cycles were employed including those used in emissions certification, sulfate testing, and highway fuel economy.

Emissions from two heavy-duty four stroke direct injection engines designed to use methanol fuel, one using Diesel pilot fuel injection and the other using spark ignition, were characterized in this program along with those from a comparably-sized Diesel engine. Emissions evaluated during both steady-state and transient FTP procedures included regulated gases (HC, CO, and NOx), unburned methanol, aldehydes, other gaseous organics, total particulate, sulfate, soluble organics in particulate and BaP. The engines adapted for methanol fuel and using catalysts emitted less HC, CO, particulate, soluble organics, and BaP than the Diesel fueled engine.

A fleet of 64 heavy-duty 1970-71 model trucks and buses powered by a variety of diesel engines were tested periodically to determine exhaust smoke behavior. Smoke tests were made when the vehicle was new or nearly new and at four month intervals thereafter, or until 160,934 km (100,000 miles) odometer reading was reached. Gaseous emissions of hydrocarbon (HC), carbon monoxide (CO), and nitric oxide (NO) were measured at one point early in the project. Both smoke and gaseous emission tests were performed with chassis versions of the engine dynamometer Federal Test Procedures (FTP). Results in terms of “a” (acceleration), “b” (lugging), and “c” (peak) smoke factors versus mileage are reported for the 13 engine-vehicle-application groupings.

To characterize exhaust emissions from water-cooled 2-stroke outboard motors (the predominant type), four new motors were tested on dynamometer stands. The engines ranged from 4-65 hp in size, and operating conditions were chosen along lines of simulated boat loading. All the measurements were taken at steady-state conditions. Emission concentrations were measured in raw exhaust gas and after the gases had been bubbled through water in a specially constructed tank. Constituents measured included hydrocarbons, CO, CO2, NO, NOx, O2, light hydrocarbons, and aldehydes. Emissions of sulfur oxides (SOx) were estimated on the basis of fuel consumed, and all the exhaust emissions data were used with available information on population and usage of motors to estimate exhaust emission factors and national exhaust emissions impact.

The research program on which this paper is based included both laboratory emission measurements and extrapolation of results to the national population of heavy-duty farm, construction, and industrial engines. Emission tests were made on four gasoline engines and eight diesel engines typical of those used in F, C, and I equipment. Gaseous and particulate emissions were measured during engine operation on well-accepted steady-state procedures, and diesel smoke was measured during both steady-state conditions and the Federal smoke test cycle. Emissions measured were hydrocarbons, CO, CO2, NO, NOx, O2, aliphatic aldehydes, light hydrocarbons, particulate, and smoke. Emission of sulfur oxides (SOx) was estimated on the basis of fuel consumed, and both evaporative and blowby hydrocarbons were also estimated where applicable (gasoline engines only). Data on emissions obtained from this study were compared with those available in the literature, where possible.