Search Results

In order to use modeling as a predictive tool for real-world particulate filter designs (segmented filters, non-axisymmetric designs), it is necessary to develop reliable 3-dimensional models. This paper presents a 3 d modeling approach, which is validated against engine-bench measurements with both FBC and CDPF systems. Special emphasis is given to the prediction of the transient inlet flow distribution, which is realized without resorting to external CFD software. The experimental and modeling results illustrate the 3-d nature of the problem, induced by the heat capacity and conductivity effects of the cement layers. It is possible to predict the localization of regeneration in certain areas of the filter (partial regeneration), as a result of poor heat transfer to thermally isolated regions in the filter. The accuracy of the model was validated by extensive comparisons with temperature measurements in 30 positions inside the filters and at various operating conditions.

The paper will model a welding process as a moving heat source through the work piece and investigate the effectiveness of various pre-heating mechanisms, including moving heat sources and the thermal strips. The reduction of thermal conductivity in the material around the tool due to rising temperature will be considered in the study. The paper represents an initial attempt to develop a nonlinear, time-discontinuous, p-version Galerkin method for the study of thermal effects in the Friction Stir Welding (FSW) process. Numerical results and the topics for further studies are presented.

This SAE Standard specifies the test methods, dimensions, and requirements for single core 60 V cables intended for use in road vehicle applications where the nominal system voltage ≤60 V DC (25 V AC). It also specifies additional test methods and/or requirements for 600 V cables intended for use in road vehicle applications where the nominal system voltage is >60 V DC (25 V AC) to ≤600 V DC (600 V AC). Where practical, this standard uses ISO 6722 for test methods, dimensions, and requirements. This standard covers ISO conductor sizes which usually differ from SAE conductor sizes. It also covers the individual cores in multicore cables. See ISO 6722 for “Temperature Class Ratings”.

This Standard specifies the test methods, dimensions, and requirements for single-core 60 V cables intended for use in road vehicle applications where the nominal system voltage ≤ 60 V DC (25 V AC). It also specifies additional test methods and/or requirements for 600 V cables intended for use in road vehicle applications where the nominal system voltage is > 60 V DC (25 V AC) to ≤ 600 V DC (600 V AC). Where practical, this standard uses ISO 6722 for test methods, dimensions, and requirements. This standard covers ISO conductor sizes which usually differ from SAE conductor sizes. It also covers the individual cores in multi-core cables. See ISO 6722 for “Temperature Class Ratings”.

This Standard specifies the test methods, dimensions, and requirements for single-core 60 V cables intended for use in road vehicle applications where the nominal system voltage ≤ 60 V DC (25 V AC). It also specifies additional test methods and/or requirements for 600 V cables intended for use in road vehicle applications where the nominal system voltage is > 60 V DC (25 V AC) to ≤ 600 V DC (600 V AC). Where practical, this standard uses ISO 6722 for test methods, dimensions, and requirements. This standard covers ISO conductor sizes which usually differ from SAE conductor sizes. It also covers the individual cores in multi-core cables. See ISO 6722 for “Temperature Class Ratings”.

A 1200-V, 600-A silicon carbide (SiC) JFET half-bridge module has been developed for drop-in replacement of a 600-V, 600-A IGBT intelligent power module (IPM). Advances in the development of SiC field effect transistors have resulted in reliable high yield devices that can be paralleled and packaged to produce high-voltage and high-current power modules not only competitive with existing IGBT technology but the modules have expanded capabilities. A SiC vertical junction field effect transistor VJFET has been produced with the properties of lower conduction loss, zero tail current, higher thermal conductivity, and higher power density when compared to a similarly rated silicon IGBT or any practical SiC MOSFETs previously reported. Three prototype SiC JFET half-bridge modules with gate drivers have been successfully integrated into a three-phase 30-kW (continuous), 100-kW (intermittent) AC synchronous motor drive designed to control a traction motor in an electric vehicle.

A 2-D CFD model was developed to describe the heat transfer, and reaction kinetics in a honeycomb structured ceramic diesel particulate trap. This model describes the steady state as well as the transient behavior of the flow and heat transfer during the trap regeneration processes. The trap temperature profile was determined by numerically solving the 2-D unsteady energy equation including the convective, heat conduction and viscous dissipation terms. The convective terms were based on a 2-D analytical flow field solution derived from the conservation of mass and momentum equations (Opris, 1997). The reaction kinetics were described using a discretized first order Arrhenius function. The 2-D term describing the reaction kinetics and particulate matter conservation of mass was added to the energy equation as a source term in order to represent the particulate matter oxidation. The filtration model describes the particulate matter accumulation in the trap.

Automotives play a very important role in day-to-day human lives. The exhaust gas emitted from automotive vehicles of current technologies is one of the major contributions to global temperature increment. It is important to develop a system that can conserve energy and incorporate it into current vehicles which are in use. Phase change materials (PCM) are well known for energy storage applications because of their crucial thermophysical property known as latent heat of fusion. The gas from the exhaust pipe of automobiles can be considered a turbulent jet. With this assumption in this study, a system is proposed by combining jet impingement and phase change material at the exhaust pipe of automobiles to recover the thermal energy which is being let out into the atmosphere as waste. Liquid Gallium is chosen as a phase change material for this study because of its high thermal conductivity nature compared to other hydrocarbon-based phase change materials.

Abstract This article discusses a multi-item planning and scheduling problem in a job-shop system with consideration of energy consumption. Planning is considered by a set of periods, each one is characterized by a demand, energy, and length. Scheduling is determined by the sequences of jobs on available resources. A Mixed-Integer Linear Programming (MILP) problem is formulated to integrate planning and scheduling, it is considered as an NP-difficult problem. A Genetic Algorithm (GA) is then developed to solve the MILP, and then a hybridized approach of simulated annealing with genetic algorithm (HGASA) is presented to optimize the results. Finally, numerical results are presented and analyzed to evaluate the effectiveness of the proposed algorithms.

Austempered Ductile Iron (ADI) samples were heat treated to produce materials with tensile strengths in the range of 100 ksi to 170 ksi. Microalloyed steels were also produced with equivalent tensile and yield strength levels. These steels were evaluated for mechanical properties in terms of tensile and yield strength, ductility, impact toughness, fracture toughness and fatigue strength. Machinability was extensively evaluated through tests of drilling, turning and plunge machining. This paper reports on this comprehensive comparative evaluation of these two important classes of materials for use in the automotive industry.

Automotive friction materials are composites containing three kinds of components: an organic binder, fiber for reinforcement, and property modifiers. At low braking temperatures, the wear rate of the friction materials is controlled primarily by abrasive and adhesive mechanisms. At higher braking temperatures, the wear rate increases exponentially with increasing temperature due to thermal degradation of the binder and other components, and the exponential wear rate is frequently accompanied by brake fade. Thus, one method of reducing thermal wear and fade tendency is to lower the temperature at the rotor/friction material interface. Since the rate of heat transfer from the interface is mostly dependent upon the conductive and convective modes, a rotor of high thermal conductivity will have a significant advantage over a rotor of low conductivity, if the heat capacity remains the same.

A drag dynamometer was used to evaluate the performance of automotive brake drums made from four kinds of materials with different thermal conductivities. In the order of decreasing thermal conductivity they are chromium copper, aluminum/cast iron composite, cast iron, and nickel-aluminum bronze. All of the drums were of the standard configuration used in SAE J 661a, or closely approximated it. The drums were run in conjunction with three types of lining materials: nonabrasive, moderately abrasive, and highly abrasive. Temperatures near the lining/drum interface, coefficients of friction, and lining wear were measured and compared. For a given amount of work done, the temperature near the drum surface was found to be lowest for the chromium copper drums, with progressively higher temperatures in the aluminum/cast iron composite, nickel-aluminum bronze, and cast iron drums. Relative lining wear and coefficient of friction varied with the type of lining tested.

In automotive body manufacturing the dies for blanking/trimming/piercing are under most severe loading condition involving high contact stress at high impact loading and large number of cycles. With continuous increase in sheet metal strength, the trim die service life becomes a great concern for industries. In this study, competing trim die manufacturing routes were compared, including die raw materials produced by hot-working (wrought) vs. casting, edge-welding (as repaired condition) vs. bulk base metals (representing new tools), and the heat treatment method by induction hardening vs. furnace through-heating. CaldieTM, a Uddeholm trademarked grade was used as trim die material. The mechanical tests are performed using a WSU developed trimming simulator, with fatigue loading applied at cubic die specimen’s cutting edges through a tungsten carbide rod to accelerate the trim edge damage. The tests are periodically interrupted at specified cycles for measurement of die edge damage.

Two different aluminium alloy materials have been used to produce ventilated brake discs, on one hand, AS17G0.6 hypereutectic alloy and on the other hand, AS7G0.6 reinforced with 20% in wt. of SiC particles. The casting production technique used has been Low Pressure Casting (LPC) and some of the brake discs have been heat treated using a T6 treatment. Once the ventilated brake discs were produced and machined, they were tested in a dynamometer in order to compare the performance under service conditions of the aluminum alloy and grey cast iron (GCI) discs currently used in the market.

The effect of rotor alloy composition on thermal conditions in a disc brake system was determined analytically. The three alloys selected were gray cast iron, 356 aluminum, and copper -1% chromium. This study includes calculations of the temperature and heat storage in the various portions of the brake system, as well as the variations of convective heat transfer throughout the system. These computations were made for the transient conditions existing during a series of 60 mph stops (15 ft/sec2 deceleration). The steady-state rotor surface temperature and the thermal gradients were found to decrease with increasing thermal conductivity of the alloys. The rotor surface temperatures for the first two stops were relatively independent of thermal conductivity, but were strongly dependent on heat capacity. Convection was found to occur almost entirely (greater than 90%) from the rotor surface and ventilating passages.

Three different models, the law-of-the-wall, a modified law-of-the-wall, and an approximate one-dimensional solution to the energy equation are compared for the spatially-resolved prediction of engine heat tranfer. The multidimensional hydrodynamic code KIVA is used for the fluid mechanic simulation. Two different engine geometries are studied; one being a pancake-shaped chamber, and the other a bowl-in-piston geometry. The comparisons are done for a range of initial conditions of gas flow. Rates-of-pressure-rise were also varied to represent rates typical of those encountered in motored engines, and those found in fired engines. Comparisons with experimental results show that the heat transfer predictions using the law-of-the-wall may be in error when source terms such as the transient, work and chemical energy terms have a significant effect in determining the temperature profile in the boundary layer.

This work is based in a model of neural and wavelets networks using published experimental data. The objective is to compare a neural and a wavelet network estimating the creep rupture strength based on chemical composition of Fe-2.25Cr-Mo and Fe-(9-12)Cr steels, and on its heat treatment temperature and life time. It will be determined the configuration that provides the best fit of the data.

Atomized iron powder was screened to narrow fractions and annealed. Intermetallic Fe3P powder was blended with the fractions to provide an alloy containing 0.45% phosphorus after sintering. Cores were pressed to a density of 7.4 g/cm3 and sintered at temperatures ranging from 1600°F (870°C) to 2600°F (1430°C) in hydrogen. Magnetic properties were determined from the sintered cores and compared with previous properties measured for iron and hot repressed 0.45% phosphorus iron. It was found that the induction at any density level was approximately 500 gausses (0.05 teslas) lower than for iron. Remanent magnetization was influenced by the size of the pores. If pores were large, remanent magnetization was 8 K gausses (0.8 teslas) and increased to 12 K gausses (1.2 teslas) as the pores become finer. Both maximum permeability and the coercive force were improved when 0.45% phosphorus was added.

Bearing oil film thickness (BOFT) values were determined for the front sain bearing of a four-cylinder engine at different engine speeds, loads, and oil temperatures using two different measurement techniques. The total resistance technique assumes the oil film can be modelled as a simple ohmic resistor. The total capacitance technique assumes the oil film can be described as a simple capacitor. A comparison of results determined using both methods for a set of single-grade oils demonstrates that, although the methods agree quantitatively for certain combinations of engine test conditions and oils, the level of precision with the total capacitance technique is greater than with the total resistance technique. This difference is attributed to the fact that the oil dielectric constant, which is needed for calculating BOFT values in the total capacitance method, can be measured more precisely than can the oil conductivity, which is needed in the total resistance method.

The adequacy of the fuels with the engines has been often a major goal for the oil industry or car manufacturers. As the formulation of fuels becomes more complex, the use of numerical simulation provides an efficient way to understand and analyze the combustion process. These conclusions become increasingly true with the appearance of second generation biofuels. This paper describes a methodology for the representation of fuels and biofuels using a lumping procedure combined with adequate thermodynamic and thermophysical models. This procedure allows computing different thermodynamic and thermophysical properties for simulation purposes in internal combustion engines. The lumping approach involves reducing analytical data to a few pseudo-components characterized by their molecular weight, critical properties and acentric factor.