Search Results

In the truck industry there is a continuous demand to increase the efficiency and to decrease the emissions. To acknowledge both these issues a waste heat recovery system (WHR) is combined with a partially premixed combustion (PPC) engine to deliver an efficient engine system. Over the past decades numerous attempts to increase the thermal efficiency of the diesel engine has been made. One such attempt is the PPC concept that has demonstrated potential for substantially increased thermal efficiency combined with much reduced emission levels. So far most work on increasing engine efficiency has been focused on improving the thermal efficiency of the engine while WHR, which has an excellent potential for another 1-5 % fuel consumption reduction, has not been researched that much yet. In this paper a WHR system using a Rankine cycle has been developed in a modeling environment using IPSEpro.

A comprehensive study is carried out in order to better understand combustion behavior in a direct injection Diesel engine working under multiple injection strategies, in particular when using post-injections. The aim of the study is to provide criteria to more easily define optimized injection strategies. During the study two main phenomena have been observed and characterized: an acceleration of the final stage of combustion and an apparent disconnection between the combustions of the two pulses (“split flame”). Thanks to the combustion acceleration phenomenon, if the post-injection is placed near enough the main injection, the end of combustion can take place even earlier compared to the case with a single main injection. In such conditions NOx emissions increase (most likely due to a higher temperature level during the last stage of combustion), but soot and specific fuel consumption decrease (due to a faster last phase of combustion).

In recent years, stricter regulations on emissions and higher demands for more fuel efficient vehicles have led to a greater focus on increasing the efficiency of the internal combustion engine. Nowadays, there is increasing interest in the recovery of waste heat from different engine sources such as the coolant and exhaust gases using, for example, a Rankine cycle. In diesel engines 15% to 30% of the energy from the fuel can be lost to the coolant and hence, does not contribute to producing work on the piston. This paper looks at reducing the heat losses to the coolant by increasing coolant temperatures within a single cylinder Scania D13 engine and studying the effects of this on the energy balance within the engine as well as the combustion characteristics. To do this, a GT Power model was first validated against experimental data from the engine.

Compared to the gasoline engine, the diesel engine has the advantage of being more efficient and hence achieving a reduction of CO₂ levels. Unfortunately, particulate matter (PM) and nitrogen oxides (NOx) emissions from diesel engines are high. To overcome these drawbacks, several new combustion concepts have been developed, including the PCCI (Premixed Charge Compression Ignition) combustion mode. This strategy allows a simultaneous reduction of NOx and soot emissions through the reduction of local combustion temperatures and the enhancement of the fuel/air mixing. In spite of PCCI benefits, the concept is characterized by its high combustion noise levels. Currently, a promising way to improve the PCCI disadvantages is being investigated. It is related with the use of low cetane fuels such as gasoline and diesel-gasoline blends.

A commercially available fuel, E85, a blend of ~85% ethanol and ~15% gasoline, can be a viable substitute for fossil fuels in internal combustion engines in order to achieve a reduction of the greenhouse gas (GHG) emissions. Ethanol is traditionally made of biomass, which makes it a part of the food-feed-fuel competition. New processes that reuse waste products from other industries have recently been developed, making ethanol a renewable and sustainable second-generation fuel. So far, work on E85 has focused on spark ignition (SI) concepts due to high octane rating of this fuel. There is very little research on its application in CI engines. Alcohols are known for low soot particle emissions, which gives them an advantage in the NOx-soot trade-off of the compression ignition (CI) concept.

Most of the new Diesel combustion concepts are mainly based on reducing local combustion temperatures and enhancing the fuel/air mixing with the aim of simultaneously reducing soot and NOx emissions. In this framework, Premixed Charge Compression Ignition (PCCI) has revealed as one of the best options to combine both low emissions and good combustion controllability. During last years, PCCI strategy has been widely explored using high EGR levels and different early or late injection timings to extend the ignition delay. Recently, the use of lower cetane fuels is under investigation. Despite the great quantity of research work performed, there are still some aspects related to PCCI combustion that are not completely well known. In this paper an experimental and numerical study is carried out focused on understanding the mixing and auto-ignition processes in PCCI combustion conditions using Diesel and Gasoline fuels.

Fuel effects on ignition delay and low temperature reactions (LTR) during partially premixed combustion (PPC) were analyzed using Design of Experiments (DoE). The test matrix included seventeen mixtures of n-heptane, isooctane, toluene and ethanol covering a broad range of ignition quality and fuel chemistry. Experiments were performed on a light-duty diesel engine at 8 bar IMEPg, 1500 rpm with a variation in combustion phasing, inlet oxygen concentration and injection pressure. A single injection strategy was used and the start of injection and injection duration were adjusted to achieve the desired load and combustion phasing. The experimental data show that fuels with higher Research Octane Number (RON) values generally produced longer ignition delays. In addition, the alcohol content had significantly stronger effect on ignition delay than the aromatic content.

In this paper the effect of the engine load and the EGR (exhaust gas recirculation) rate on the combustion process and the pollutant emissions when using RME (rapeseed methyl-ester) is investigated. For this purpose a parametric study in a single-cylinder HSDI (high speed direct injection) engine in a wide range of operating conditions (thus trying to maximize the generality of the results) has been carried out. All the output parameters are compared with the corresponding ones for a reference diesel fuel at equivalent engine performances and operating conditions. To perform a rigorous comparison, a specific methodology has been designed based on the comparison at equivalent engine load and oxygen mass fraction in the intake manifold, so as to remove the effect of the fuel properties (derived from the different oxygen content, mainly) on the engine performances.

In this study, an investigation was made on a heavy duty diesel engine using both conventional diesel combustion mode and a partially premixed combustion (PPC) mode. A segment mesh was built up and modeled using the commercial CFD code AVL FIRE, where only the closed volume cycle, between IVC and EVO, was modeled. Both combustion modes were validated using experimental data, before a number of heat flux boundary conditions were applied. These conditions were used to evaluate the engine response in terms of engine performance and emission levels for the different percentage of heat rejection. The engine performance was measured in terms of specific fuel consumption and estimated power output, while the calculated net soot and accumulated NOx mass fractions were used for comparing the emission levels. The results showed improved efficiency for both combustion types, but only the PPC combustion mode managed that without increasing the production of NOx emissions severely.

Recently, internal combustion engine design has been moving towards downsized, more efficient engines. One key in designing a more efficient engine is the control of heat losses, i.e., improvements of the thermodynamic cycle. Therefore, there is increasing interest in examining and documenting the heat transfer process of an internal combustion engine. A heavy-duty diesel engine was modeled with a commercial CFD code in order to examine the effects of two different gasoline fuels, and the injection strategy used, on heat transfer within the engine cylinder in a partially premixed combustion (PPC) mode. The investigation on the fuel quality and injection strategy indicates that the introduction of a pilot injection is more beneficial in order to lower heat transfer, than adjusting the fuel quality. This is due to reduced wall exposure to higher temperature gases and more equally distributed heat losses in the combustion chamber.

Recent studies have shown that the use of highly premixed dual fuel combustion reduces pollutant emissions and fuel consumption in CI engines. The most common strategy for dual fueling is to use two injection systems. Port fuel injection for low reactivity fuel and direct injection for high reactivity fuel. This strategy implies some severe shortcomings for its real implementation in passenger cars such as the use of two fuel tanks. In this sense, the use of a single injection system for dual fueling could solve this drawback trying to maintain pollutant and efficiency benefits. Nonetheless, when single injection system is used, the spray characteristics become an essential issue. In this work the fundamental characteristics of dual-fuel sprays with a single injection system under non-evaporating engine-like conditions are presented.

Partially Premixed Combustion, PPC, with 50% Exhaust Gas Recirculation (EGR) at lean combustion conditions λ =1.5, has shown good efficiency and low emissions in a heavy-duty single-cylinder engine. To meet emission requirements in all loads and transient operation, aftertreatment devices are likely needed. Reducing λ to unity, when a three-way catalyst can be applied, extremely low emissions possibility exists for stoichiometric PPC. In this study, the possibility to operate clean PPC from lean condition to stoichiometric equivalence ratio with reasonable efficiency and non-excessive soot emission was investigated. Two EGR rates, 48% and 38% with two fuel rates were determined for 99.5 vol% ethanol in comparison with one gasoline fuel and Swedish diesel fuel (MK1). Engine was operated at 1250 rpm and 1600 bar injection pressure with single injection. Results revealed that efficiency was reduced and soot emission increased from lean PPC to stoichiometric PPC operation.

The concept of Partially Premixed Combustion (PPC) in internal combustion engines has shown to yield high gross indicated efficiencies, but at the expense of gas exchange efficiencies. Most of the experimental research on partially premixed combustion has been conducted on compression ignition engines designed to operate on diesel fuel and relatively high exhaust temperatures. The partially premixed combustion concept on the other hand relies on dilution with high exhaust gas recirculation (EGR) rates to slow down the combustion which results in low exhaust temperatures, but also high mass flows over cylinder, valves, ports and manifolds. A careful design of the gas exchange system, EGR arrangement and heat exchangers is therefore of utter importance. Experiments were performed on a heavy-duty, compression ignition engine using a fuel consisting of 80 volume % 95 RON service station gasoline and 20 volume % n-heptane.

Fleet electrification has been demonstrated as a feasible solution to decarbonize the heavy-duty transportation sector. The combination of hybridization and advanced combustion concepts may provide further advantages by also introducing reductions on criteria pollutants such as nitrogen oxides and soot. In this scenario, the interplay among the different energy paths must be understood and quantified to extract the full potential of the powertrain. One of the key devices in such powertrains is the battery, which involves different aspects regarding operation, safety, and degradation. Despite this complexity, most of the models still rely on resistance-capacity models to describe the battery operation. These models may lead to unpractical results since the current flow is governed by limiters rather than physical laws. Additionally, phenomena related with battery degradation, which decreases the nominal capacity and enhances the heat generation are also not considered in this approach.

Partially Premixed Combustion (PPC) is used to meet the increasing demands of emission legislation and to improve fuel efficiency. PPC with gasoline fuels have the advantage of a longer premixed duration of fuel/air mixture which prevents soot formation at higher loads. The objective of this paper is to investigate the degree of stratification for low load (towards idle) engine conditions using different injection strategies and negative valve overlap (NVO). The question is, how homogenous or stratified is the partially premixed combustion (PPC) for a given setting of NVO and fuel injection strategy. In this work PRF 55 has been used as PPC fuel. The experimental engine is a light duty (LD) diesel engine that has been modified to single cylinder operation to provide optical access into the combustion chamber, equipped with a fully variable valve train system. Hot residual gases were trapped by using NVO to dilute the cylinder mixture.

The current research focus on fuel effects on low temperature reactions (LTR) in Homogeneous Charge Compression Ignition (HCCI) and Partially Premixed Combustion (PPC). LTR result in a first stage of heat release with decreasing reaction rate at increasing temperature. This makes LTR important for the onset of the main combustion. However, auto-ignition is also affected by other parameters and all fuel does not exhibit LTR. Moreover, the LTR does not only depend on fuel type but also on engine conditions. This research aims to understand how fuel composition affects LTR in each type of combustion mode and to determine the relative importance of chemical and physical fuel properties for PPC. For HCCI the chemical properties are expected to dominate over physical properties, since vaporization and mixing are completed far before start of combustion.

Our previous research investigated the sensitivity of combustion phasing to intake temperature and injection timing during the transition from homogeneous charge compression ignition (HCCI) to partially premixed combustion (PPC) fuelled with generic gasoline. The results directed particular attention to the relationship between intake temperature and combustion phasing which reflected the changing of stratification level with the injection timing. To confirm its applicability with the use of different fuels, and to investigate the effect of fuel properties on stratification formation, primary reference fuels (PRF) were tested using the same method: a start of injection sweep from -180° to -20° after top dead center with constant combustion phasing by tuning the intake temperature. The present results are further developed compared with those of our previous work, which were based on generic gasoline.

The combustion process in a homogeneous charge compression ignition (HCCI) engine is mainly governed by ignition wave propagation. The in-cylinder pressure, heat release rate, and the emission characteristics are thus largely driven by the chemical kinetics of the fuel. As a result, CFD simulation of such combustion process is very sensitive to the employed reaction mechanism, which model the real chemical kinetics of the fuel. In order to perform engine simulation with a range of operating conditions and cylinder-piston geometry for the design and optimization purpose, it is essential to have a chemical kinetic mechanism that is both accurate and computational inexpensive. In this paper, we report on the evaluation of several chemical kinetic mechanisms for methanol combustion, including large mechanisms and skeletal/reduced mechanisms.

In the challenge to reduce CO2, NOx and PM emissions, the application of natural gas or biogas in engines is a viable approach. In heavy duty and marine, either a conventional dual fuel (CDF), or a reactivity-controlled compression ignition (RCCI) approach is feasible on existing diesel engines. In both technologies a pilot diesel injection is used to ignite the premixed natural gas. However, the influence of injection-timing and -pressure on the start of combustion timing (SOC) is opposite between both modes. For a single operating point these relations can be explained by a detailed CFD simulation, but an intuitive overall explanation is lacking. This makes it difficult to incorporate both modes into one engine application, using a single controller. In an experimental campaign by the authors, on a medium speed engine, the lowest emissions were found to be very close to the SOC corresponding to the transition from RCCI to CDF.

This study examines fuel auto-ignitability and shows a method for determining fuel performance for HCCI combustion by doing engine experiments. Previous methods proposed for characterizing HCCI fuel performance were assessed in this study and found not able to predict required compression ratio for HCCI auto-ignition (CRAI) at a set combustion phasing. The previous indices that were studied were the Octane Index (OI), developed by Kalghatgi, and the HCCI Index, developed by Shibata and Urushihara. Fuels with the same OI or HCCI Index were seen to correspond to a wide range of compression ratios in these experiments, so a new way to describe HCCI fuel performance was sought. The Lund-Chevron HCCI Number was developed, using fuel testing in a CFR engine just as for the indices for spark ignition (research octane number and motor octane number, RON and MON) and compression ignition (cetane number, CN).